Control Technologies 2500 Series User manual

2500C-PS-24V-35 24VDC 35 Watt Power Supply
DESCRIPTION
The 2500C-PS-24V-35 is a triple wide module that
provides power for the CPU and all IO modules
plugged in the Compact Chassis.
FEATURES
Control Technology Inc.
5734 Middlebrook Pike, Knoxville, TN 37921-5914
Phone: [phone] Fax: [phone]
www.controltechnology.com
Power Supply Specifications
Field Wiring Connector 3 Pin Removable Connector
Input Voltage Operating
Range 20 VDC to 30 VDC
Total Wattage Rating 35 watts maximum output
@ 0º to 60ºC
Steady State Input Current
at full Load 1.57 Amps max @ 24VDC
Peak Inrush Current 17.26 Amps max @ 24VDC
Fusing Littelfuse 0213005.MX
250V IEC SLO 5x20mm 5A I2T=314
Hold Up Time 8mSec @ 35 Watt Full Load
Module Size Triple wide module
Isolation 24 VDC to
Backplane 1500VAC
Isolation 24 VDC to
Chassis 1500VDC
Operating Temp Range 0ºC to 60ºC (32ºF to 140ºF)
Storage Temperature -40ºC to 85ºC (-40ºF to 185ºF)
Relative Humidity 5% to 95% (non-condensing)
Shipping Weight 2.0 lb. (0.91 Kg)
Agency Approvals Pending
UL, ULC, FM(Class 1, Div 2), CE
2500 Series Compact System
 Triple wide module
 24VDC Power Supply
 Maximum 35 watts backplane power
 8 mSec holdup time
Copyright© 2015 Control Technology Inc All Rights Reserved January 2015

2500 Series Compact System
Control Technology Inc.
5734 Middlebrook Pike, Knoxville, TN 37921-5914
Phone: [phone] Fax: [phone]
www.controltechnology.com
2500C-PS-24V-35 24VDC 35 Watt Power Supply
Warning:
Disable all power to the base before
installing or removing the power
supply. Failure to do so could cause
damage to the equipment or injury to
personnel.
2500C Compact Power Sup-
plies are always located in the
left most slot
Caution:
Do not attempt to operate the 2500C
-PS-24V-35 out of the Voltage Op-
erating Ranges specified. Damage to
the Power Supply could occur if out
of range power input is applied.
Installing Power Wiring
Use the following steps for installing and removing the 2500C-PS-24V-35 Power Supply from the 2500C Chassis.
1. Position the power supply so that the bezel is facing you.
2. Grasp the top and bottom of the power supply.
3. Carefully slide the power supply into the left most slot in the base until it engages into the backplane connector.
4. Strip power wiring back, insert the wire into the wiring connector as shown above, then tighten screws.
5. Check to make sure the power input wires are securely inserted and the fastened in the wiring connector.
6. Insert and tighten down the 3 pin removable wiring connector.
7. Be sure to tighten the top and bottom bezel screws completely.
8. Once all the chassis modules including controllers and IO are inserted then you may apply power to the power supply
inputs.
To remove the power supply, remove power from the power input by removing the power wiring connector or turning off the
power source, loosen the bezel screws, and pull the power supply forward out of the chassis until it clears the chassis.
Copyright© 2015 Control Technology Inc All Rights Reserved 21 January 2015