Convair CoolTower CTF05 User manual

(English) (CTF05)
OWNER’S MANUAL
CoolTower CTF05
®

General Safety
Please read these instructions before
using the fan and keep for future
reference.
This appliance is not intended for use by
persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been
given supervision or instruction in using
the appliance by a person responsible
for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
Do not poke anything through the
ventilating slits.
Assemble the fan completely before use.
Always use the fan in an upright position.
Stand it on a firm, solid, horizontal base
(not on thick pile carpets).
Clean the air inlets and outlets at regular
intervals to prevent airflow reduction
(refer Maintenance section).
For indoor use only. Do not use this fan
outdoors, or on wet surfaces. Do not
use the fan near flammable areas or
substances.
Electrical Safety
Before connecting your electrical power
cord to a power outlet, check that the
fan voltage is the same as your power
supply. The fan voltage will be stated on
the rating label.
Make sure that the fan never comes into
contact with water.
Never turn the fan on if the lead is
damaged or if the fan’s casing is
obviously damaged.
If the power supply cord is damaged it
must be replaced by the manufacturer, a
service agent or similarly qualified
persons in order to avoid a hazard.
Do not pull the fan along by the power
cord. Always uncoil the power cord
completely.
Always turn the fan off and unplug from
the power socket when not in use.
SEELEY INTERNATIONAL – OWNER’S MANUAL 1
SAFETY

General Safety
Please read these instructions before
using the fan and keep for future
reference.
This appliance is not intended for use by
persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been
given supervision or instruction in using
the appliance by a person responsible
for their safety.
Children should be supervised to ensure
that they do not play with the appliance.
Do not poke anything through the
ventilating slits.
Assemble the fan completely before use.
Always use the fan in an upright position.
Stand it on a firm, solid, horizontal base
(not on thick pile carpets).
Clean the air inlets and outlets at regular
intervals to prevent airflow reduction
(refer Maintenance section).
For indoor use only. Do not use this fan
outdoors, or on wet surfaces. Do not
use the fan near flammable areas or
substances.
Electrical Safety
Before connecting your electrical power
cord to a power outlet, check that the
fan voltage is the same as your power
supply. The fan voltage will be stated on
the rating label.
Make sure that the fan never comes into
contact with water.
Never turn the fan on if the lead is
damaged or if the fan’s casing is
obviously damaged.
If the power supply cord is damaged it
must be replaced by the manufacturer, a
service agent or similarly qualified
persons in order to avoid a hazard.
Do not pull the fan along by the power
cord. Always uncoil the power cord
completely.
Always turn the fan off and unplug from
the power socket when not in use.
SEELEY INTERNATIONAL – OWNER’S MANUAL 1
SAFETY

Remote Control Storage
Replacing the battery
The remote control is stored in the
remote control holder located at the top
of the rear enclosure as shown in Fig 2.
Your remote control is supplied with
batteries. To begin use, open the
battery cover and remove the plastic tag
located between the two batteries (Fig
3). Check the polarity is correct and
replace the back cover.
When the fan’s power is on, the remote
control can be used to operate the fan
from up to 6m away. Note: if there are
two or more fans within this distance,
both will be operated by the same
remote control.
Component List
Assembly
1 Remote Control
2 Main Body
3 Base
4 Base Screws x3
5 Clamp Screws x2
6 Power Cord & Plug
Unpack the fan and check that you have
all of the components.
Remove the screws from the base,
locate the base onto the main fan body
and screw into position.
Screw the cord clamp into position on
the base.
2CTF05
ASSEMBLY
O n -G re e n
O ff-L ig h t O ff
O n -G re e n
O ff-L ig h t O ff
L o w s p e e d -R e d
M id s p e e d - O r a n g e
H i g h s p e e d - G r e e n
1 8 0 D e g re e -G r e e n
1 2 0 D e g re e -O ra n g e
6 0 D e g re e -R e d
D i s a b le - L ig h t O f f
2 h o u rs -R e d
4 h o u rs -O r a n g e
8 h o u rs -G r e e n
D i s a b le - L ig h t O f f
P O W E R --T o s ta rt o r s to p th e fa n
S P E E D -- T o a d ju s t th e s p e e d le v e l: lo w / m e d iu m / h ig h
O S C IL L A T IO N --T o s e t o s c illa tio n a n g le o r s to p o s c illa tio n
T IM E R -- T o s e t th e tim e r le v e l: 2 /4 /8 h o u rs
W IN D -- T o s e t n o rm a l w in d o r n a tu ra l w in d m o d e
L E D B u tto n F u n c tio n
Operation
Wind Function
Insert the plug into the power outlet.
Turn the fan ON by pressing the
‘POWER’ button on the unit or remote
control (refer Fig 4). The fan will
rotate to the operation position as
shown (Fig 5).
Each button press will change the
colour & illumination of the LED display
as indicated in Fig 4. Select the desired
fan speed (low-med-high) by pressing
the FAN button. Each press will cycle
between the speeds.
Turn the fan OFF by pressing the
‘POWER’ button at any time.
The fan has a natural wind function
which simulates a changing breeze. To
activate, press the ‘WIND’ On/Off button
on the control panel.
OPERATION
Timer Function
The fan has a timer function that will
turn off the fan. By pressing the timer
button 2, 4 and 8 hour delays are
available. To cancel, press the button
until the timer indicators are no longer lit.
Press the oscillation button on the
control panel to enable the oscillation
function. The fan will swing from side to
side in a 60°, 120° or 180° arc. Press
again to stop oscillation.
Do not force or hinder the oscillation
movement. All LEDs will flash if any
abnormal restriction occurs.
Oscillation Function
®
SEELEY INTERNATIONAL – OWNER’S MANUAL 3
1
2
34
5
Press the power button to start the fan.
Note: The fan will rotate anti-clockwise as shown.
Once power is turned off unit will rotate clockwise
and return to its home position .
On: Green
Off: Light Off
Low Speed: Red
Mid Speed: Orange
High Speed: Green
On: Orange
Off: Light Off
2 hours: Red
4 hours: Orange
8 hours: Green
Disable: Light Off
180 Degree: Green
120 Degree: Orange
60 Degree: Red
Disable: Light Off

Remote Control Storage
Replacing the battery
The remote control is stored in the
remote control holder located at the top
of the rear enclosure as shown in Fig 2.
Your remote control is supplied with
batteries. To begin use, open the
battery cover and remove the plastic tag
located between the two batteries (Fig
3). Check the polarity is correct and
replace the back cover.
When the fan’s power is on, the remote
control can be used to operate the fan
from up to 6m away. Note: if there are
two or more fans within this distance,
both will be operated by the same
remote control.
Component List
Assembly
1 Remote Control
2 Main Body
3 Base
4 Base Screws x3
5 Clamp Screws x2
6 Power Cord & Plug
Unpack the fan and check that you have
all of the components.
Remove the screws from the base,
locate the base onto the main fan body
and screw into position.
Screw the cord clamp into position on
the base.
2CTF05
ASSEMBLY
O n -G re e n
O ff-L ig h t O ff
O n -G re e n
O ff-L ig h t O ff
L o w s p e e d - R e d
M id s p e e d - O r a n g e
H i g h s p e e d - G r e e n
1 8 0 D e g re e -G r e e n
1 2 0 D e g re e -O ra n g e
6 0 D e g re e -R e d
D i s a b le - L ig h t O f f
2 h o u rs -R e d
4 h o u rs -O r a n g e
8 h o u rs -G r e e n
D i s a b le - L ig h t O f f
P O W E R --T o s ta rt o r s to p th e fa n
S P E E D -- T o a d ju s t th e s p e e d le v e l: lo w / m e d iu m / h ig h
O S C IL L A T IO N --T o s e t o s c illa tio n a n g le o r s to p o s c illa tio n
T IM E R -- T o s e t th e tim e r le v e l: 2 /4 /8 h o u rs
W IN D -- T o s e t n o rm a l w in d o r n a tu ra l w in d m o d e
L E D B u tto n F u n c tio n
Operation
Wind Function
Insert the plug into the power outlet.
Turn the fan ON by pressing the
‘POWER’ button on the unit or remote
control (refer Fig 4). The fan will
rotate to the operation position as
shown (Fig 5).
Each button press will change the
colour & illumination of the LED display
as indicated in Fig 4. Select the desired
fan speed (low-med-high) by pressing
the FAN button. Each press will cycle
between the speeds.
Turn the fan OFF by pressing the
‘POWER’ button at any time.
The fan has a natural wind function
which simulates a changing breeze. To
activate, press the ‘WIND’ On/Off button
on the control panel.
OPERATION
Timer Function
The fan has a timer function that will
turn off the fan. By pressing the timer
button 2, 4 and 8 hour delays are
available. To cancel, press the button
until the timer indicators are no longer lit.
Press the oscillation button on the
control panel to enable the oscillation
function. The fan will swing from side to
side in a 60°, 120° or 180° arc. Press
again to stop oscillation.
Do not force or hinder the oscillation
movement. All LEDs will flash if any
abnormal restriction occurs.
Oscillation Function
®
SEELEY INTERNATIONAL – OWNER’S MANUAL 3
1
2
34
5
Press the power button to start the fan.
Note: The fan will rotate anti-clockwise as shown.
Once power is turned off unit will rotate clockwise
and return to its home position .
On: Green
Off: Light Off
Low Speed: Red
Mid Speed: Orange
High Speed: Green
On: Orange
Off: Light Off
2 hours: Red
4 hours: Orange
8 hours: Green
Disable: Light Off
180 Degree: Green
120 Degree: Orange
60 Degree: Red
Disable: Light Off

To maximise the efficiency of the fan,
clean the inlet and outlet grilles regularly.
• Unplug the fan from the mains power
supply before cleaning.
• Use a soft, damp cloth to wipe the
outside. Never use thinners or other
strong chemicals on the fan surfaces.
• Use a vacuum cleaner to remove dirt
and dust from the inlet and outlet
grilles.
• Ensure the fan is dry before plugging
back into the mains power supply.
MAINTENANCE
®
4CTF05
As the policy of this company is one of continuous improvement, all specifications
are subject to change without notice.
Waste electrical products must not be disposed of with household
waste. This product should be taken to your local recycling centre for
safe treatment.
SEELEY INTERNATIONAL – OWNER’S MANUAL 5
WARRANTY
Subject to the terms of the warranty Seeley International Pty Ltd (”Seeley”) will repair or
replace at its option, the product or any part thereof, which examination shows to be defective
for a period of 24 months from purchase.
This warranty is conditional upon the fan being used only for personal, domestic or household
purposes and installed and operated in accordance with our instructions, and does not apply
to:
For technical assistance before returning the product please contact:
!
!
!
!
!
Adjustments necessary due to misuse of the fan,
Normal user maintenance,
Setting of controls,
Transit damage, or
Damage caused by user misuse, tampering, or failure to observe the care
and special provisions in the instructions.
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
No other person, firm or corporation is authorised by us to offer or give on our behalf any other
or greater warranty than that given under this warranty. The benefits conferred by this
warranty are in favour of the original retail purchaser and any person deriving title to the goods
through or under such person and are in addition to other rights and remedies of the consumer
under a law in relation to the goods or services to which the warranty relates.
To make a warranty claim, you will need to return the appliance along with the original
invoice/receipt to the place of purchase for assessment.
It is your responsibility to cover all forwarding and return freight costs incurred in returning the
appliance to the place of purchase, or if necessary, in sending the appliance to a service
centre.
Please complete the following for your records:
Seeley's address is 112 O'Sullivan Beach Road, Lonsdale, South Australia 5160, and the
telephone number is 08 8328 3850.
Please retain your original invoice/receipt as proof of purchase. Every request for
warranty must be accompanied by proof of purchase.
Serial Number:
Product
Model
Purchased from
Date purchased
:
...................................................................
Convair
:
: ...................................................................
...................................................................
: ....../....../...... The above warranty applies only to Australia.
CTF05
1300 650 399

To maximise the efficiency of the fan,
clean the inlet and outlet grilles regularly.
• Unplug the fan from the mains power
supply before cleaning.
• Use a soft, damp cloth to wipe the
outside. Never use thinners or other
strong chemicals on the fan surfaces.
• Use a vacuum cleaner to remove dirt
and dust from the inlet and outlet
grilles.
• Ensure the fan is dry before plugging
back into the mains power supply.
MAINTENANCE
®
4CTF05
As the policy of this company is one of continuous improvement, all specifications
are subject to change without notice.
Waste electrical products must not be disposed of with household
waste. This product should be taken to your local recycling centre for
safe treatment.
SEELEY INTERNATIONAL – OWNER’S MANUAL 5
WARRANTY
Subject to the terms of the warranty Seeley International Pty Ltd (”Seeley”) will repair or
replace at its option, the product or any part thereof, which examination shows to be defective
for a period of 24 months from purchase.
This warranty is conditional upon the fan being used only for personal, domestic or household
purposes and installed and operated in accordance with our instructions, and does not apply
to:
For technical assistance before returning the product please contact:
!
!
!
!
!
Adjustments necessary due to misuse of the fan,
Normal user maintenance,
Setting of controls,
Transit damage, or
Damage caused by user misuse, tampering, or failure to observe the care
and special provisions in the instructions.
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
No other person, firm or corporation is authorised by us to offer or give on our behalf any other
or greater warranty than that given under this warranty. The benefits conferred by this
warranty are in favour of the original retail purchaser and any person deriving title to the goods
through or under such person and are in addition to other rights and remedies of the consumer
under a law in relation to the goods or services to which the warranty relates.
To make a warranty claim, you will need to return the appliance along with the original
invoice/receipt to the place of purchase for assessment.
It is your responsibility to cover all forwarding and return freight costs incurred in returning the
appliance to the place of purchase, or if necessary, in sending the appliance to a service
centre.
Please complete the following for your records:
Seeley's address is 112 O'Sullivan Beach Road, Lonsdale, South Australia 5160, and the
telephone number is 08 8328 3850.
Please retain your original invoice/receipt as proof of purchase. Every request for
warranty must be accompanied by proof of purchase.
Serial Number:
Product
Model
Purchased from
Date purchased
:
...................................................................
Convair
:
: ...................................................................
...................................................................
: ....../....../...... The above warranty applies only to Australia.
CTF05
1300 650 399

00139501-D convair.net.au AU 1107
Warranty Service
Australia 1-300-650-399
seeleyinternational.com
It is the policy of Seeley International to introduce continual
product improvement. Accordingly, specifications are
subject to change without notice. Please consult with your
dealer to confirm the specifications of the model selected.
®