Conversor MultiPack User manual

Distributed By
:
Distributed By: Distributed By
User Guide
Conversor
® MultiPack
•
Front-row sound
quality
for multiple users
•
Enhances desired
sounds near and
at a distance
•
Ideal for classroom, lecture
& meeting environments
Complete
Assistive
Listening
Device Kit
•
Reduces unwanted
background noise
Conversor Limited
Tel:
[phone]
Fax
:
+44
(0)870 066 3669
info
@conversorproducts.com
www.conversorproducts.com
MANUFACTURED IN THE UK FOR
CONVERSOR LIMITED
The Lansbury Estate
,
Lower Guildford Road, Knaphill, Woking,
Surrey GU21 2EP, United Kingdom
HBK01MP
P

Thank you for your purchase of the
Conversor MultiPack,
a comp
lete assistive listening device kit designed to provide
front-row sound level and clarity for multiple users in a room.
The Conversor MultiPack consists in its standard confi guration
of 2 Conversor
Microphone/Transmitters
and 8 Conversor
Pendant Receivers
, all of which are stored in a rugged carrying
case that is also used to charge the units.
Each
Microphone/Transmitter
can either be held in the hand and
Microphone/Transmitter can either be held in the hand and Microphone/Transmitter
pointed at the desired sound source, placed on a table or podium
using the convenient fold-out stand, or worn by the speaker using
the neck cord provided. The
Pendant Receiver
is worn around the
Pendant Receiver is worn around the Pendant Receiver
neck by users of Telecoil-equipped hearing instruments. Please
refer to
The Conversor User Guide
for information about
operation of the Microphone/Transmitter and the Receiver.
Charging the Microphone/Transmitters and
Receivers in the Conversor MultiPack Case
Before using The Conversor MultiPack, please make sure that all
units in the case are fully charged by following these instructions:
Plug the Mains Lead into the socket on side of the Carrying
Case
. The ON/OFF switch next to the socket should be in
the OFF position. Please see Figure 1.
Plug the Chargin
g Cable
Jacks
into the
Microphone/
Transmitters and Receivers as shown in Figure 2.
Plug the Mains Lead into an electrical outlet. Push the ON/
OFF switch to the ON position. Please see Figure 3.
The
Charger L
EDs on the front panel will fl ash green
to show that the c
h
arging cycle has begun.
The Charger LEDs will stop fl ashing and illuminate
constantly when their respective batteries are charged.
Charging time is approximately 2 1/2 hours providing
up to 8 hours of continuous use.
2
3
Welcome!
6.
The Charger LEDs will stop fl ashing and illuminate
5.
The Charger LEDs will stop fl ashing and illuminate
4.
The
4.
The
3.
Plug the Mains Lead into an electrical outlet. Push the ON/
3.
Plug the Mains Lead into an electrical outlet. Push the ON/
2.
1.
Approximate
battery life
1 Hour
2 Hours
4 Hours
6 Hours
8 Hours
Charge time on fully
discharged batteries
25 Minutes
40 Minutes
65 Minutes
90 Minutes
120 Minutes
Pendant Receiver
The LEDs on the
front panel signify
the following:
OFF:
Not switched
on at the power source
Flashing Green:
Charging in process
Green:
Green: Green:
Charging
cycle complete
Figure 1:
Plugging Mains
Lead into Carrying Case.
ON/OFF switch in the
OFF position
Figure 2:
Plugging
Charging Cable
Plugging Charging Cable Plugging
Jacks into Microphone/Transmitters
and Pendant Receivers
Figure 3:
ON/OFF switch
in
the ON position
LEDs on the
front panel
indicate the
status of
charging
Microphone
Microphone
Microphone
/ Transmitter
/ Transmitter
/ Transmitter
ON/OFF switch