Conviron CMP6050 User manual

CMP6050
O PERATOR'S MANUAL
Software Version 3.10
At Conviron we develop and implement innovative
and reliable controlled environment solutions.
CMP6050
®

CMP6050
OPERATOR'S MANUAL
PLEASE READ THESE INSTRUCTIONS
CAREFULLY AND COMPLETELY
BEFORE OPERATING.
Published by:
CONVIRON
590 Berry Street
Winnipeg, Manitoba
Canada R3H 0R9
www.conviron.com
May 2011
EU declaration of conformity available upon request.
Printed in Canada.
©2011 Controlled Environments Limited.
Conviron is a registered trademark of Controlled Environments Limited. All other trademarks are the property of their respective
owners. Information subject to change without written notice.

®May 2011 |Revision 3.0 i
PREFACE
Welcome to the Operator’s Manual for Conviron’s CMP6050 Control System. This Manual
has been developed to assist with the setup and daily operation of the CMP6050. The
Manual is provided to all clients who have purchased a chamber(s) containing the new
CMP6050 control system.
The Manual has been designed to provide sufficient detail for the majority of chamber
configurations, including a structured format that provides step-by-step instructions. Clients will
find sufficient detail for a typical installation including figures, diagrams, and graphics to operate
the chamber without issue. However, given that many installations are specific to each facility
and that facilities may have unique requirements, additional information or assistance from
Conviron may be required. In such cases, contact information is provided on the following page.
The CMP6050 has a security feature to manage Users' level of access. This feature requires
all Users to be set-up with the appropriate access as determined by the facility manager/
security administrator (up to 3 User ID passwords can be assigned). Once this is completed
(and provided Security is turned on), Users are required to login. This is to ensure that Program
modifications are made by authorized personnel only. The Administrator can override all Users
and can access all programming functionality with the exception of features set at the factory.
The CMP6050 offers three password-protected security levels:
UÊ Users (Access Level 1)
UÊ Administrators (Access Level 2)
UÊ Factory (Access Level 3)
Security Access levels associated with various features are identified throughout this manual and
listed in Section 7.0. The CMP6050 is shipped with security features turned Off. This enables
any User to start the chamber and become familiar with the chamber controls without having
to enter a password.
It is recommend that a security Administrator be assigned to administer User
login authority and that security features be added as soon as possible.
This equipment is only to be used by authorized personnel – that is, personnel who have been
trained on the proper use of the equipment and who have read this manual.
The manual incorporates CMP6050 software version 3.10.

®May 2011 |Revision 3.0 iii
SERVICE AND TECHNICAL SUPPORT
Conviron welcomes the opportunity to provide assistance and to answer any technical questions
related to the start-up, use and general technical support and troubleshooting of the CMP6050
control system. Before contacting Conviron, please check the following:
UÊ Read this Operator’s Manual in its entirety for information about the feature(s) with
which you are experiencing trouble.
UÊ If you are having a problem using your CMP6050, pay particular attention to
the relevant section and the pertinent information in this Manual, and use the
information to diagnose and correct the problem. If the problem persists and/or
you require additional assistance, please collect the following information prior
to contacting Conviron:
UÊ The serial number of the chamber which is located on the rating plate
on the side of the chamber and at the icon.
UÊ The software version number of the CMP6050 software. Instructions
for obtaining the CMP6050 software version number are provided in
Section 4.0 Main Status Screen under the Information Icon.
UÊ A description of the problem.
UÊ A description of what you were doing before the problem occurred.
Head office
Technical Services
Conviron
590 Berry St.
Winnipeg, Manitoba,
Canada R3H 0R9
Conviron Technical Services
North America Europe
Toll free +1.800.363.6451 +44.(0).800.032.6422
Telephone [phone] +44.(0).1638.781.731
Fax [phone] +44.1638.741.112
Email [email protected] [e-mail]

®May 2011 |Revision 3.0 v
USER NOTICE
Following product installation and commissioning, the facility manager/user is to register
the Conviron product that has been purchased on Conviro
Net ™ at www.conviron.com.
Instructions for doing so are located on the peel-off decal located on your control panel and
as pictured below:
USER NOTICE
THIS NOTICE IS TO BE ACTIONED BY THE FACILITY MANAGER /
USER OF THIS EQUIPMENT FOLLOWING PRODUCT INSTALLATION
AND COMMISSIONING.
CONVIRO NET ™ PORTAL
Conviro Net ™is a secure portal that offers value added services to our clients.
Electronic manuals Tech Specs Hard copy manuals
Data Sheets Brochures Bulletins
Warranty Registrations
CONVIRO NET ™ REGISTRATION
To register for access to Conviro Net and to register your product warranty, please follow
these steps:
Step 1: Remove this decal and take it to your workstation. If you have received multiple
new chambers/rooms, please remove the decal from each chamber and take to
your workstation.
Step 2: Log on to the Conviron website: www.conviron.com.
Step 3: In the top right corner of the website Home page, click on the Conviro
Net logo to
launch the Conviro
Net portal.
Step 4: If you are already registered with Conviro
Net , login using your Username and
Password. If you are not registered, please follow the online registration process.
Registering for the site also includes registering your product warranty which requires
inserting the product serial number for each new chamber.
The serial number for this chamber is __________________________________________.
Note: The registration process requires Conviron authorization. You will receive an
authorization email typically within one working day.
Step 5: Login to Conviro Net regularly to access the available tools and to review recent news
about Conviron.
For assistance please contact Kathy Burton at [e-mail].
10091

®May 2011 |Revision 3.0 vii
TABLE OF CONTENTS
PREFACE.................................................................................................................... i
SERVICE AND TECHNICAL SUPPORT..................................................................... ii
USER NOTICE.......................................................................................................... iii
1.0 PRECAUTIONS ................................................................................................1-1
2.0 INTRODUCTION TO THE CMP6050 CONTROL SYSTEM..............................2-1
2.1 An Overview of the CMP6050 ........................................................................................................2-1
2.1.1 The Controller .......................................................................................................2-1
2.1.2 The Display............................................................................................................2-2
2.1.3 The Software .........................................................................................................2-2
2.2 General Specifications.....................................................................................................................2-2
2.3 Local Control Interface - Programming and Scheduling............................................................2-3
2.4 Data Logging and Management ...................................................................................................2-3
2.4.1 Local Data..............................................................................................................2-3
2.4.2 Remote Data .........................................................................................................2-3
2.5 Alarms ................................................................................................................................................2-4
2.6 Security ..............................................................................................................................................2-4
2.7 Start-Up Delay...................................................................................................................................2-4
2.8 Communications ..............................................................................................................................2-4
2.9 Auxiliary Contacts.............................................................................................................................2-4
2.10 Optional Accessories.....................................................................................................................2-5
3.0 INITIAL START-UP AND NAVIGATION OVERVIEW ........................................3-1
3.1 Turning the Display On....................................................................................................................3-1
3.2 Setting the Time and Date .............................................................................................................3-1
3.2.1 Time/Date..............................................................................................................3-2
3.3 Other Initial Start-Up Parameters...................................................................................................3-4
3.4 Navigation Overview .......................................................................................................................3-4
3.4.1 LED Indicator Lights..............................................................................................3-4
3.4.2 LCD Touch-Screen................................................................................................3-4
3.4.3 Interactive Keys .....................................................................................................3-5
3.5 Battery................................................................................................................................................3-5
3.6 Component Stability........................................................................................................................3-5

®
May 2011 |Revision 3.0
viii
4.0 MAIN STATUS SCREEN ...................................................................................4-1
4.1 Information Icon ...............................................................................................................................4-2
4.2 Chamber Status/Alarm Status........................................................................................................4-3
4.3 Chamber Selector Icon....................................................................................................................4-3
4.4 Main Menu Bar .................................................................................................................................4-4
4.5 Bottom Menu Bar.............................................................................................................................4-5
4.6 Controlled Parameters ....................................................................................................................4-6
5.0 PROGRAM SCREEN ........................................................................................5-1
5.1 Program Screen Icons and Locations ............................................................................................5-1
5.2 Program Screen Main Menu...........................................................................................................5-2
5.3 Accessing the Program Screen ......................................................................................................5-2
5.3.1 Create Program.....................................................................................................5-3
5.3.2 Edit Program .........................................................................................................5-6
5.3.3 Delete Program.....................................................................................................5-7
5.4 Schedule Screen...............................................................................................................................5-8
5.4.1 Edit Schedule ........................................................................................................5-8
5.4.2 Start/Stop ............................................................................................................5-10
5.4.3 Clear Schedule ....................................................................................................5-11
6.0 ALARM SCREEN ..............................................................................................6-1
6.1 Alarm Screen Icons...........................................................................................................................6-1
6.2 Alarm Overview ................................................................................................................................6-1
6.3 RAMP and STEP MODE..................................................................................................................6-2
6.3.1 Tracking-RAMP Mode vs. STEP Mode................................................................6-3
6.3.2 STEP Mode Limits.................................................................................................6-4
6.3.3 RAMP and STEP Mode - Alarms and Shutdown ................................................6-4
6.4 Setting Alarms ..................................................................................................................................6-5
6.4.1 When in Ramp Mode............................................................................................6-5
6.4.2 When in Step Mode..............................................................................................6-6
6.5 Alarm Status Indicators....................................................................................................................6-7
6.6 Alarm Corrective Action ..................................................................................................................6-8
6.7 Alarm Types.......................................................................................................................................6-9
TABLE OF CONTENTS

®May 2011 |Revision 3.0 ix
6.8 Alarm History ................................................................................................................................. 6-10
6.9 Clear Alarms................................................................................................................................... 6-11
7.0 SECURITY SCREEN..........................................................................................7-1
7.1 Security Overview.............................................................................................................................7-1
7.2 CMP6050 Level Access....................................................................................................................7-2
7.3 Security Screen Icons and Locations .............................................................................................7-3
7.4 Edit User Screen ...............................................................................................................................7-3
7.5 Login Security Screen ......................................................................................................................7-5
7.6 Logout Security Screen....................................................................................................................7-6
8.0 OPTION SCREEN ............................................................................................8-1
8.1 Option Screen-Layout .....................................................................................................................8-1
8.2 Input Offset (Sensor Calibration)....................................................................................................8-2
8.3 (Chamber) Startup Delay.................................................................................................................8-3
8.4 Time/Date .........................................................................................................................................8-4
8.5 Setup..................................................................................................................................................8-4
8.5.1 Process Control Mode - RAMP vs. STEP.............................................................8-4
8.5.2 Preferences — Fan Speed Control and Exhaust Damper Control ...................8-5
8.5.3 Data Storage Location..........................................................................................8-7
8.6 Security on/off...................................................................................................................................8-7
9.0 TREND SCREEN...............................................................................................9-1
LOCAL DISPLAY DATA ......................................................................................................9-2
9.1 Trend Screen – Key Area Layout ....................................................................................................9-2
9.1.1 Pan Mode Screen Fields.......................................................................................9-3
9.2 How to Pan on the Trend Screen ...................................................................................................9-4
9.3 How to Zoom on the Trend Screen ...............................................................................................9-4
9.3.1 Zoom Mode Screen Fields...................................................................................9-4
REMOTE DATA ..................................................................................................................9-5
9.4 Logged Data – Network..................................................................................................................9-5
9.4.1 Setting the IP address at the PC (for Windows 7 only) ......................................9-6
9.4.2 Selecting an IP for the Controller ........................................................................9-8
9.4.3 Setting the IP Address at the Controller.............................................................9-8
9.4.4 To access the Controller Using FTP to download data (for Windows 7 only)..9-10
TABLE OF CONTENTS

®
May 2011 |Revision 3.0
x
10.0 SERVICE SCREEN ........................................................................................10-1
10.1 Service Screen Icons ................................................................................................................... 10-2
10.2 I/O Status...................................................................................................................................... 10-2
10.3 Scalable Options:........................................................................................................................ 10-5
GLOSSARY ............................................................................................................... A

®May 2011 |Revision 3.0 1-1
1.0 PRECAUTIONS
The following symbols are used throughout this manual to draw your attention to important warnings,
guidelines and product information. Please take note of their respective meanings.
Hazard Warning Important Information
Dangerous Electrical Current Please Note
Hot Surface Grounding Mark
Slippery Surface Caution, Moving Parts
Please note the following Hazard warnings before operating this equipment:
UÊ This equipment is only to be operated and maintained by authorized personnel - that is,
personnel who have been trained on the proper operation and/or maintenance of the
equipment and who have read this manual.
UÊ If in doubt about safe operation and/or maintenance of the equipment, contact the
responsible party immediately.
UÊ Prior to operating, users should conduct a visual inspection of the equipment and surrounding
area by walking around the unit and checking both inside and outside to ensure no debris or
obstacles are present that could pose a safety hazard. If operators see a potential hazard (e.g.
water accumulating on the  oor which could be slippery, an obstruction that would prevent
the door from opening/closing properly) they should take appropriate steps such as alerting
service personnel.
UÊ Before starting, the operator should ensure that all electrical boxes are in the closed
position and that no one is present in the chamber – either servicing or working
within/on the unit.
UÊ Ensure that no one is using or could activate the room remotely during operation or
maintenance activities.
UÊ Avoid water coming in contact with the electrical components, as it presents a risk of
water damage to both high and low voltage electrical components. If you have any
doubt of safe watering practices, contact Conviron.
UÊ When a Schedule is not running, Alarms are disabled! No one other than a single,
designated on-site service technician should be operating the chamber. Altering
output parameters to troubleshoot a chamber, while others are handling mechanical or
electrical systems within the chamber, COULD BEHAZARDOUS AND MAY RESULT IN
PERSONAL INJURY. As such, manipulation of output parameters must be performed
with either a qualified service technician present or via phone support with Conviron’s
Technical Services group.

®
May 2011 |Revision 3.0
1-2
CHAPTER 1 | PRECAUTIONS
UÊ Qualified trades-people such as electricians, plumbers, refrigeration mechanics, etc.
should perform all work as required by local codes and regulations.
UÊ Central Management™ (CM) is an optional feature. If CM is being used it becomes
inextricably linked to the use of the Controller and therefore, both the Central
Management manual and the Controller Operators Manual must be read and
understood in their entirety prior to operation.
UÊ Working with high voltage will be required when installing this equipment. Do NOT
attempt this work unless you have the appropriate knowledge and experience. Take
appropriate safety precautions and ensure that the building power supply to the
chamber is off prior to installation.
UÊ The main terminal in the control panel has live voltage unless the external breaker is
OFF. Use extreme caution when working in the control panel to prevent injury.
UÊ Water that could come in contact with the electrical components presents a high
voltage hazard. Avoid these conditions. If you have any doubt of safe watering
practices, contact Conviron.
UÊ Controller may come equipped with an optional Uninterrupted Power Supply (UPS)
such that power will remain live for a period of time even if the power supply is turned
OFF. Use extreme caution when working on the control panel to prevent injury. If you
have any doubts as to whether your unit comes equipped with a UPS, contact Conviron.
UÊ Inside the control panel is an independent temperature shut-off device called the
ir33. This ir33 acts as a secondary fail-safe protector that shuts off the chamber if its
temperature limits are exceeded. The ir33 is set by Conviron and is factory protected
(requires Access Level 3). The factory default setting for the ir33 temperature limit is
ten degrees beyond the chamber operating range. The standard operating range of a
chamber is +4C to +45C while the standard ir33 shut down settings are -6C to +55C
depending on the size of the chamber, size of the compressor and other factors. Always
verify, when changing the (Alarm) Temperature within the 6050 setup, that the limits
are still within the minimum and maximum operating limits for the Chamber. This will
ensure that the ir33 only triggers in the event that the actual temperature exceeds the
Chamber's minimum or maximum temperature limit by 10 degrees. It will also ensure
that the ir33 does not trigger 'before' a high or low temperature tracking alarm. The ir33
is located inside the control panel where there is live high voltage. Contact Conviron
Client Services for more information or help if necessary.
UÊ Surfaces and lighting may become hot during operation. Always take appropriate
precautions and do not operate if users will remain inside the chamber for more
than a few minutes unless adequate shielding or other safety precautions are taken.
NOTE: HID lamps can cause serious skin burn and eye in ammation from short-wave
ultraviolet radiation if the lamp envelope is punctured or broken.
UÊ Operators should note that water may accumulate on the  oor which could be slippery
and pose a safety hazard. Always ensure  oors remain dry and wear non-slip footwear.

®May 2011 |Revision 3.0 2-1
2.0 INTRODUCTION TO THE CMP6050 CONTROL SYSTEM
The first step in becoming familiar with Conviron’s new CMP6050 Control system is to
understand the key components of the system and the general specifications. This section
introduces the CMP6050 control system and provides an overview of its features and capabilities.
Topics covered in this section include:
UÊ An overview of the CMP6050
UÊ General Specifications
2.1 An Overview of the CMP6050
Temperature, humidity and lighting intensity control are three examples of important parameters
required in most controlled environment systems. Whether the controlled environment is used
for plant science research, or research in such other areas as pharmaceutical, nutraceutical,
materials testing, or any of the other myriad applications of a Conviron controlled environment
system, certain parameters require control and monitoring. For Conviron, this is accomplished
with its next-generation CMP6050 control system.
The CMP6050 is configured for each application from the factory and offers a wide array of
set-up, control and alarm features to fine tune the configuration on site. The scalability of the
CMP6050 also accommodates additional Input/Output ports if necessary. This  exibility enables
users to add sensors allowing the CMP6050 to adapt when changing or modifying experiments.
The CMP6050 control system consists of three primary components:
s Controller
UÊ Display
UÊ Control system Software.
2.1.1 The Controller
The Controller (Figure 2-1: CMP6050 Controller) is
mounted inside the chamber’s control cabinet and
comprises the actual Programmable Logic Controller
(PLC). The controller’s job is to monitor the control
parameters and adjust the outputs to coincide with the
User’s programs/schedule. The controller also notifies
the User with alarms when parameters, for any number
of reasons, deviate outside of specified limits.
Figure 2-1: CMP6050 Controller

®
May 2011 |Revision 3.0
2-2
CHAPTER 2 | INTRODUCTION TO THE CMP6050 CONTROL SYSTEM
2.1.2 The Display
The Display (Figure 2-2: CMP6050 Display) provides the interface to the control system by
facilitating interaction directly with the controller. To accomplish this, the Display uses both an
LCD (Liquid Crystal Display) touch screen and push-button ‘Keys’. There are also three LED
indicator lights on the Display which are used for notifying the User of various conditions.
The touch-screen Display provides access to the following functions:
UÊ Programming and Scheduling
UÊ Alarm
UÊ Security
UÊ Logging
UÊ Graphing
UÊ Service
Information on the touch screen is easy
to read because the screen is backlit.
Icons are ‘touch-activated’ and initiate a
controller action when they are ‘tapped’ (or
activated) with the stylus.
2.1.3 The Software
The controller Software is installed into the controller by Conviron at the time of chamber
manufacture and facilitates interaction with, and control of, the chamber. Like other software
products, the CMP6050 software carries a ‘Version’ number – this, because Conviron is
continuously working to enhance its product capabilities resulting in software version number
changes. Accessing the installed software version number for the controller is described in
Figure 3-2, under Information Icon.
2.2 General Specifications
a. The CMP6050 control system is a robust industrial grade PLC control system designed
for a wide range of controlled environment applications.
b. The display uses a 6 inch touch-screen LCD.
c. Alarms are color-coded directly on the screen making alarm conditions quick to identify
and resolve.
d. All control processes (temperature, humidity, light and CO2) set-point changes can be set
in either ‘Step’ or ‘Ramp’ mode.
e. A default ‘Status Screen’ amalgamates set points and actual conditions into a single, concise
‘dashboard’ for easy viewing and improved chamber management.
Figure 2-2: CMP6050 Display
LED Indicator
Lights
Interactive
Touch-screen
Keys

®May 2011 |Revision 3.0 2-3
CHAPTER 2 | CMP6050 Operator’s Manual
2.3 Local Control Interface - Programming and Scheduling
a. Touch-screen LCD.
b. Real-time clock programming of control variables.
c. Can store a maximum of 16 real-time, user-entered ‘Programs’.
d. Can store up to 48 ‘Time-lines’ per program (with one minute resolution).
e. Programs are then entered into a ‘Schedule’ (a sequence of up to 8 program entries) to
create a single day, multi day, seasonal or infinite schedule.
f. Temperature, humidity, light and CO2transitions set as either ‘Step’ or ‘Ramp’.
2.4 Data Logging and Management
Log data for the CMP6050 can be viewed two ways – either locally at the control system interface
or remotely via a network-connected PC.
2.4.1 Local Data
a. The data available at the local control interface includes main chamber variables –
temperature, humidity, lighting, and CO2(if applicable).
b. Parameters are all logged automatically by the controller every 18 seconds.
c. Data can be accessed with up to five days of history.
d. Trend graphs can be viewed directly on the local control interface for both ‘set-point’
and ‘actual’ values. (only inputs)
e. Zoom and Pan functions provide additional visualization tools allowing the User to precisely
and accurately view and assess the data.
2.4.2 Remote Data
a. The data available remotely is more substantial and includes every input and output
parameter being monitored and controlled.
b. Data is logged automatically by the controller every 18 seconds regardless of the number of
parameters. This provides unprecedented data resolution for the User while it also benefits
service personnel.
c. Log data is accessed in several ways:
UÊ A network-connected PC
UÊ An internet-enabled PC
UÊ Conviron’s Central Management system (Optional)

®
May 2011 |Revision 3.0
2-4
CHAPTER 2 | INTRODUCTION TO THE CMP6050 CONTROL SYSTEM
2.5 Alarms
a. Audible and color-coded visual alarms are provided.
b. User-settable absolute alarms for all controlled processes.
c. User-settable process tracking alarms for temperature (in 'Ramp' mode) is available for the
User to determine how tightly to monitor the experiment.
d. User-settable process for disabling a controlled process, and thus alarms, at any time
while a program is running.
2.6 Security
The CMP6050 offers three password-protected levels:
Users Access Level 1
Administrators Access Level 2
Factory Access Level 3
2.7 Start-Up Delay
At start-up, CMP6050 controllers randomly select delay times between 0 and 59 seconds (by
default) to reduce start-up loads after a power failure. This delay time can also be programmed
by the User (reference Section 8-3: (Chamber) Startup Delay).
2.8 Communications
Ethernet connectivity is delivered with every controller (Note: Connectivity is optional on the
Adaptis product family). The controller is shipped communications-ready. (This does require
IT set-up however at the facility.)
2.9 Auxiliary Contacts
Alarm contacts for connection to a Building Management System (BMS) or (optional) auto dialer.

®May 2011 |Revision 3.0 2-5
CHAPTER 2 | CMP6050 Operator’s Manual
2.10 Optional Accessories
AUX: Programmable Output: Provides an auxiliary switch, terminated in the control panel, for
timed control of automatic watering, nutrient dosing, etc.
SEN: Thermistor temperature sensors available in 10ft (3m), 30ft (10m) and 50ft (15m) lengths
(please consult factory).
ADIAL: An automatic telephone dialing system (autodialer) to notify the User of a chamber
alarm. Note that this requires Conviron’s Central Management™ system, which is sold as a
separate product. Consult Conviron Client Services for more information.

®May 2011 |Revision 3.0 3-1
3.0 INITIAL START-UP AND NAVIGATION OVERVIEW
Now that a general overview of the capabilities of the CMP6050 Control system have been
presented, it’s time for the initial start-up. This section provides instructions on start-up
procedures and general navigation of the CMP6050 control system. Where appropriate,
diagrams, actual screen-shots, and step-by-step instructions are provided.
Do not touch the screen with sharp or pointed objects. Use only the stylus
provided. Use of any other objects on the display screen may damage the
screen and void the warranty.
Operate your CONVIRON equipment for a few days before introducing any
plant material to acquaint yourself with the equipment’s operation and to ensure
the equipment meets the requirements for your experiments.
3.1 Turning the Display On
The CMP6050 is shipped from Conviron with the
latest software installed and with the control system
configured for each specific application. Whenever the
chamber is turned on, the first screen to be displayed
is the Chamber Selector screen shown in Figure 3-1.
The Conviron ‘wave’ icon displayed in this screen
represents the chamber(s) that is (are) controllable
from the display. Each display can control up to ten (10)
chambers. If the display has been configured to control
more than one chamber, then the Chamber Selector
screen will show additional Icons to represent the additional chambers. The ‘blinking’ Icon
with the red border represents the chamber currently active with the display.
For example, Figure 3-1: Chamber Selector Screen illustrates that the Display is set up to control
two chambers with chamber number 1 being the currently selected chamber. To select a different
chamber, simply tap the 'Next' tab at the bottom left of the screen with the stylus and then tap
the ‘Select’ option at the bottom-right of the screen. (To configure additional chambers to be
controlled from the same Display, refer to Section 9-4: Logged Data-Network in this Manual.)
Once the desired chamber number has been selected, the main Status Screen is displayed.
(Figure 3-2: Main Status Screen).
3.2 Setting the Time and Date
The next step required during the initial start-up is to set the Time and Date. Generally speaking,
these steps are required the first time the control system is used, and thereafter only if/when
these parameters require changing. They will also be required at times of battery replacement
(battery life is approximately 5 years).
Figure 3-1: Chamber Selector Screen

®
May 2011 |Revision 3.0
3-2
CHAPTER 3 | INITIAL START-UP AND NAVIGATION OVERVIEW
The Time and Date set-up can be accessed in two ways – from the main Status
Screen and also from the Options Screen. For this Section of the Manual,
instructions are provided for accessing these parameters from the Status Screen
only. Section 8.0: Option Screen Icons and Locations covers these features via
access from the Options Screen.
Figure 3-2: Main Status Screen illustrates the Bottom Menu Bar located along the bottom of
the Status Screen. Although this Menu Bar presents four (4) functional Icons, at this stage of
the controller set-up, it is only necessary to set up the proper Time and Date.
Figure 3-3: Bottom Menu Bar
3.2.1 Time/Date Access Level 1
Time and Date are essential to the chamber experiment and it is recommended that they be
viewed periodically (daily) to prevent experimental error.
Figure 3-2: Main Status Screen
Chamber Selector
Information Icon
Controlled Parameters
Main Menu Bar
Bottom Menu Bar
Chamber status/
Alarm status

®May 2011 |Revision 3.0 3-3
CHAPTER 3 | CMP6050 Operator’s Manual
The time is displayed in a 24-hour format (00:00).
The date is displayed in day-month-year format (dd-mmm-yy).
Tap either the Time or Date icon to access the following screen (Figure 3-4: Time and Date Set-up)
and enable editing of the time and date.
1. Press the ‘ENTER’ key on the right side of the display to activate the ‘Hour’ field box.
(There should be a blinking cursor.)
Figure 3-4: Time and Date Set-up
‘Exit’ Icon
2. Press the ‘UP or ‘DOWN’ keys to edit the hour.
3. Press the ‘ENTER’ key to activate the ‘Minute’ field box.
4. Repeat Steps two and three for the other field boxes.
5. Press the ‘ENTER’ key after entering every field box when
editing the time and date.
It is essential to follow this process because it locks in the
values entered into the controller. THISISMANDATORY.
All values entered are in real-time. Ensure that the time
and date are correct and checked daily to ensure proper
experiment processing.
You can also edit time and date by using the stylus and tapping on the
appropriate numbers on the keypad. Then press the "exit" icon to lock the
values entered into the calendar.
Figure 3-5: Display Keys
Scroll Up
Enter
Scroll Down

®
May 2011 |Revision 3.0
3-4
CHAPTER 3 | INITIAL START-UP AND NAVIGATION OVERVIEW
3.3 Other Initial Start-Up Parameters
The Bottom Menu Bar at the bottom of the Main Status screen also includes two other
icons – ‘ID’ Set-Up and ‘Security’ Set-Up. These parameters are not discussed in this section
of the Manual because they are more advanced features that are not critical to the initial
‘basic’ chamber set-up. That is, they are not required in order for the User to begin using
the chamber. The objective for this section is to provide sufficient information to allow the
User to get the chamber operating with the bare essentials. Note however, that security at
this stage is still disabled.
For information related to the advanced features and options, refer to Section 8.0: Option
Screen of this Manual.
3.4 Navigation Overview
The CMP6050 Display was developed
to be intuitive for the User, while also
accounting for a vast array of interactive
options and display features. To
accomplish this, the Display uses:
UÊ Passive LED Indicator Lights to display
various conditions
UÊ An Interactive LCD Touch-Screen
UÊ Aset of interactive Keys
3.4.1 LED Indicator Lights
There are three LED indicator lights on the CMP6050 Display. Their functions are
as follows:
UÊ Top LED – Alarm Condition – Active
UÊ Centre LED – Communication Error (connection between display & controller is lost)
UÊ Bottom LED – Controller On ( ashes when running a schedule)
3.4.2 LCD Touch-Screen
The Touch-Screen has two functions – to display information and to facilitate interaction
with the Users. Here, a host of primary and secondary screens are used to provide all the
necessary information required to fully interact with the controller. Sections 4 through 10
of this Manual describe each Screen in detail. Note that the main Primary (default) Screen
is the Main Status screen.
Figure3-6: CMP6050 Display
LED Indicator
Lights
Interactive
Touch-screen
Keys