Coolmax V-400 User manual

Model: V-400
1. Function Description
This power supply is designed for personal computer. There are six DC outputs:
+5V, -5V, +12V, -12V, +12V2, +3.3V ＆ +5V
SB
, and it provides power to all computer
systems and peripherals with maximum protection.
Here are some of the key features:
S-ATA ready
All kinds of protection circuits (OVP/OPP/SCP)
Fully supports all Intel & AMD system demands
20-24Pin/4-8Pin connectors available to support both 20Pin and
24Pin socket motherboards
Tube- tide design to tidy wires
Anti-corrosive nickel plated chassis
2. How to Setup
It is rather simple to install this power supply to your precious computer tower.
Follow the steps below to finish the setup.
Step1:Open the computer tower cover; put the power supply into the
corresponding location of the tower, and then use right screws to fix the
power supply to tower.
Step2:Put the Main Power Connector, ATX12V Connector, S-ATA Connector,
Peripheral Connectors and Floppy Connectors to the corresponding male
connectors of main-board, peripheral devices (i.e. HDD, CDROM etc.)
and floppy drivers respectively. When you connect the connectors, please
pay attention to the orientation of them because of the different hole sizes.
Find the proper orientation and push down firmly making sure that the
pins are aligned.
3. Specifications
3.1 Input Requirements
The power supply shall operate as below:
1

115V (100V min.-132V max.), 10A, 60Hz
230V (200V min.-264V max.), 5.5A,50Hz
3.2 DC Output
Power distribution configuration:
Model V-400
+3.3V 20A
+5V 18A
+12V 18A
+12V2 16A
-12V 0.5A
+5V SB 2.5A
3.3 Protection
The power supply itself is designed with short circuit, over voltage and over load
protection functions described as below:
3.3.1 Short Circuit Protection
A short circuit on any DC output will cause the power to latch. The power supply
will withstand a continuous short circuit to the output without damage or overseers
to the unit. The +5V SB can be shorted indefinitely and will recover automatically when
the short is removed.
3.3.2 No Load Operation
No hazardous conditions or damage to the supply will occur with all of the DC output
connectors disconnected from the load.
2

3.3.3 Over Load Protection
When the total load exceed 130%~160% of the maximum output current, the power
supply shall be latched into the state of shutdown.
3.4 Physical Environment
Operation Conditions
The power supply shall be capable of continuous operation and meet all
electrical specification without need for adjustment when subjected to the
following environ-mental conditions:
Temp. Vs Load Condition Humidity
0 ~30C@Full Load
Operation -20C ~80C@90% Rated Load 10% ~90%RH
-20C ~80C@80@ Rated Load
Storage -20C ~80C 5% ~90%RH
No degradation of the power supply shall occur during shipping or storage at the
specified condition.
3.5 Regulatory Compliance
Our power supply has been certified to comply with multi-national Safety and
EMI.
-- UL, CUL, CSA, TUV, FCC, CB
4. Precaution
Caution: Unauthorized personnel should not do this to avoid electrical
shock!
4.1 Do not open the top cover of the power supply case.
4.2 Please keep the power supply from humidity.
5. Simple Maintenance
If power supply cannot work properly, before send for repair, please check the
following items:
5.1 Does power cord indeed plug into electrical outlet?
3

5.2 Does Input Voltage set in power supply correspond to the main source in your
environment?
5.3 Please check the output connectors plugging in proper direction and connecting
firmly.
5.4 Please turn off the power and turn it on for several times, and the interval must
be at least 5 seconds.
5.5 Having checked above items, if the power supply still does not function, please
send it back to your retailer or distributor for repair.