Cooper Lighting AMETRIX SRR User manual

3.
Universal
(4x)
2.
assembly
Pan head screw
If possible, remove ceiling tile from grid to facilitate fixture
1.
Fixture
installation.
bracket
Using cut out dimensions provided on page four(4), cut
#10-32 x3/8"
appropriate size opening in ceiling tile.
Ceiling tile
Insert fixture assembly into cut out in ceiling tile.
1. Using cut out dimensions provided on page four(4), cut
hole into dry wall and feed power wire to hole.
2. After removing fixture head, loosen #10-32 x3/8" Pan head
screws and remove cover plate closest to power feed.
3. Knock out appropriate hole for conduit and attach as shown
on page three(3).
4. Replace cover plate and secure with #10-32 x3/8" Pan head
screws and press fixture housing into hole in drywall.
(ceiling grid)
Pan head screws
Universal brackets
1.
(4x)
3/8".
(2x)
Loosely reattach brackets to both sides of fixture housing.
2. Press brackets flush to ceiling tile and secure using #10-32 x
Replacing brackets on fixture housing
#10-32 x 3/8"
1. Prior to pushing fixture into hole in drywall, tie off fixture
housing to structure using saftey wire(by others) as show on
page three(3).
2. Gently push fixture housing into hole and tighten 1/4-20 x 1
1/2" Pan head screw from inside fixture housing to tighten
drywall bracket around drywall.
3. Connect appropriate wires from fixture head and ensure all
wires are properly matched.
4. Replace fixture head assembly on keyhole screws and
tighten.
1/4-20 x1 1/2"
Pan head screw Safety wires
(by others)
(4x)
Securing the fixture in drywall
Fixture housing
(drywall)
Wiring the fixture
Conduit from
Cover plate
power source.
(by others)
#10-32 x3/8"
Pan head screws
(2x)
Do not
work must meet local/national codes and be
: Before starting any work ensure
Vault w/ visor
These installation instructions are valid with the above Ametrix styles. mount fixtures vertically.
Roundel w/ visor
Installation Instructions
3.
heet 2 of 4
Visor and Non-Visor
ADY071459 REV B (ECN80481)
3.
Warning
that all sources of power are turned off. All
performed by a certified electrician.
C- croll w/ visor
2.
Small, INDOOR
SRR
(Semi-Recessed, Remote ballast)
2.
Securing fixture to ceiling tile
Semi-recessed fixtures shown without thermal protectors

Warning: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician. Do not
mount fixtures vertically.
Installation Instructions
Vault w/ visor C- croll w/ visor Roundel w/ visor
These installation instructions are valid with the above Ametrix styles.
4.
5.
heet 3 of 4
Small, INDOOR
SRR
(Semi-Recessed, Remote ballast)
Visor and Non-Visor
ADY071459 REV B (ECN80481)
Semi-recessed fixtures shown without thermal protectors
Securing the fixtures with safety wire
(both ceiling grid and drywall)
1. If applicable, replace ceiling tile with fixture secured back into ceiling. Remove adjacent tile from ceiling to facilitate wiring.
2. Depending on location of power source, loosen #10-32 x3/8" Pan head screws and remove appropriate cover plate and
knock out appropriate hole.
3. Using conduit fitting and washer, secure conduit to cover plate.
4. Attach appropriate wires and ensure all connections are properly matched.
5. Replace cover plate and secure with #10-32 x3/8" Pan head screws.
Choose appropriate cover plate
depending on location of power
source.
Ceiling surface
#10-32 x3/8"
Pan head screw
(2x)
Wiring the fixture
(both ceiling grid and drywall)
1. After securing fixture housing to ceiling structure using provided brackets, reinforce fixture using safety wire(by others).
2. Using all four tabs located on corners of fixture housing, tie off fixture to structure using safety wire(by others).
Cover plate
Conduit
(by others)
Conduit fitting
(by others)
Conduit Nut
(by others)
Safety wire
(by others)
Fixture housing

(lamps provided by others)
Cutout Dimensions In[mm]
Use only GE or Sylvania
CFL lamps
Semi-recessed fixtures shown without thermal protectors
Installation Instructions
Vault w/ visor C- croll w/ visor Roundel w/ visor
These installation instructions are valid with the above Ametrix styles
Warning: Before starting any work ensure
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician. Do not
mount fixtures vertically.
Small, INDOOR
SRR
(Semi-Recessed, Remote ballast)
Visor and Non-Visor
heet 4 of 4
ADY071459 REV B (ECN80481)
11 1
2"
292.10
61
2"
165.10
10 3/4" Fixture head size
12 3/4" Fixture head size
Lamping Size Chart
14 1
16 "
357.19
61
2"
165.10
FIXTURE SIZE
(inches/ mm) WATTAGE # OF LAMPS LAMP TYPE LAMP DESCRIPTION
10
3/4
/ 273.05 39 W 1 T6 Ceramic Metal Halide
12
3/4
/ 323.85 70 W 1 T6 Ceramic Metal Halide
12
3/4
/ 323.85 150 W 1 T6 Ceramic Metal Halide
12
3/4
/ 323.85 26 W 1 4-Pin Triple
Tube Compact Fluorescent
12
3/4
/ 323.85 32 W 1 4-Pin Triple
Tube Compact Fluorescent
12
3/4
/ 323.85 42 W 1 4-Pin Triple
Tube Compact Fluorescent
10
3/4
/ 273.05 100 W 1 T4 Halogen (Single Ended)
12 3/4 / 323.85 150 W 1 T4 Halogen (Single Ended)
12
3/4
/ 323.85 250 W 1 T4 Halogen (Single Ended)
LAMP
(not to scale)