Cooper XNV User manual

TOOLS REQUIRED: Ratchet, 9/16" socket, flat blade screw driver, electrical wiring
tools.
INSTALLATION
STEP 1. With housing lying on a smooth, soft surface open the access door by
releasing the latch. Door may be removed by opening approximately 130°
and lifting off the hinge FIG. 1.
STEP 2. Bird guard is provided pre-cut to accommodate 1-1/2" diameter (nominal)
mounting arms. When using larger diameter mounting arms remove the
punch out section of the bird guard.
STEP 3. Using a 9/16" socket, loosen the two or optional four pipe clamp mounting
bolts enough to allow mounting arm (not included) to slide onto leveling
steps. FIG. 2
STEP 4. Close access door. Lift the housing into place, re-open access door, and
position end of mounting arm onto leveling steps so that housing is level.
Care must be taken so arm does not inadvertently strike internal
components. To avoid potential damage to fixture, ensure housing is
level both front to back and side to side by placing level on flat surface
on top of the housing.
STEP 5. Using a 9/16" socket tighten the two or optional four pipe clamp mounting
bolts to 16-18 ft-lbs.
WIRING
STEP 1. Pull service wires through mounting arm and into housing
approximately 10".
STEP 2.
a. Three-terminal block (2-wire service): Connect line service lead to
terminal that is connected to black factory-installed wire. Connect neutral
service wire to terminal that is connected to white factory-installed wire.
b. Three-terminal block (3-wire service, 2 lines, 1 ground): Connect 1 line
service lead to terminal that is connected to black factory-installed wire.
Connect other line service lead to terminal that is connected to white
factory-installed wire. Connect ground service lead to terminal that is
connected to green factory-installed wire.
c. Three-terminal block (3-wire service, 1 line, 1 neutral, 1 ground): Connect
line service lead to terminal that is connected to black factory-installed
wire. Connect neutral service wire to terminal that is connected to white
factory-installed wire. Connect ground service wire to terminal that is
connected to green factory-installed wire.
—CONTINUED
ADH130179
Customer First Center
1121 Highway 74 South
Peachtree City, GA 30269
P: 770.486.4800 F: 770.486.4801
www.cooperlighting.com
XNV LED
Area/Site Luminaire
Sheet 1 of 4
10/12/21 IMI-783
SAFETY: This fixture must be wired in accordance with the National Electrical Code
and applicable local codes and ordinances. Proper grounding is required to insure
personal safety. Carefully observe grounding procedure under installation section.
WARNING: Make certain power is OFF before starting installation or attempting any
maintenance. Risk of fire/electric shock. If not qualified, consult an electrician.
• RISK OF ELECTRIC SHOCK—Disconnect power at fuse or circuit breaker before
installing or servicing.
• RISK OF BURN—Disconnect power and allow xture to cool before servicing.
• RISK OF PERSONAL INJURY— Fixture may become damaged and/or unstable if
not installed properly. Tighten all fixture components to their recommended torque
values. Do not lift pole into place by securing lifting device to lighting fixture or
mounting arm.
INSTALLATION INSTRUCTIONS
IMPORTANT: READ BEFORE INSTALLING FIXTURE.
RETAIN FOR FUTURE REFERENCE.
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible
contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufciently for user’s purpose, please contact
your nearest representative. NOTE: Specications and dimensions subject to change without notice.
FIG. 1
Latch
Door
Hinge
Housing
Optional Photocontrol Receptacle
120°
FIG. 2Bird Guard
(2) Fully
Threaded Bolts
Pipe Clamp
Leveling Steps
Thermal Block

d. No terminal block (3-wire service, 2 lines, 1 ground): Connect 1 line
service.
lead to black factory-installed wire. Connect other line service lead
to white factory-installed wire. Connect ground service lead to green
factory-installed wire.
e. No terminal block (3-wire service, 1 line, 1 neutral, 1 ground): Connect
line service lead to black factory-installed wire. Connect neutral service
wire to white.
factory-installed wire. Connect ground service wire green factory-
installed wire.
NOTE: SEE WIRING DIAGRAM FOR ADDITIONAL WIRING DETAILS.
STEP 3. Position and secure all wires away from all other electrical components
(drivers, terminal blocks).
STEP 4. Close access door and secure latch.
PHOTOCONTROL (IF EQUIPPED)
STEP 1. Using a flat blade screw driver, loosen the two flathead screws to allow
rotation of the receptacle.
STEP 2. Insert screwdriver into center slot and rotate receptacle until indicator arrow
points north or desired direction.
STEP 3. Tighten screws.
STEP 4. Insert the photoelectric control (or shorting cap) into receptacle and twist
into locked position.
NOTE: THE PHOTOCONTROL MUST CONTAIN A SOFT, RESILIENT GASKET FASTENED
TO THE BOTTOM SURFACE TO ASSURE A PROPER WEATHER SEAL BETWEEN THE
CONTROL AND THE RECEPTACLE.
MAINTENANCE
NOTE: A regular maintenance schedule should be followed to retain optimal light
output and thermal performance.
Optical lens cleaning should be performed with a clean dry cloth to remove any
dust or other contaminants. Additional cleaning can be performed with non-abrasive
acrylic cleanser.
Remove any dirt, leaves or other foreign debris from the housing and fins.
Clean water may be used to flush the fins.
—CONTINUED
ADH130179
Customer First Center
1121 Highway 74 South
Peachtree City, GA 30269
P: 770.486.4800 F: 770.486.4801
www.cooperlighting.com
XNV LED
Area/Site Luminaire
Sheet 2 of 4
10/12/21 IMI-783
INSTALLATION INSTRUCTIONS
IMPORTANT: READ BEFORE INSTALLING FIXTURE.
RETAIN FOR FUTURE REFERENCE.
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible
contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufciently for user’s purpose, please contact
your nearest representative. NOTE: Specications and dimensions subject to change without notice.

PHOTOCONTROL (IF EQUIPPED)
STEP 1. Using a flat blade screw driver, loosen the two flathead screws to allow
rotation of the receptacle.
STEP 2. Insert screwdriver into center slot and rotate receptacle until indicator arrow
points north or desired direction.
STEP 3. Tighten screws.
STEP 4. Insert the photoelectric control (or shorting cap) into receptacle and twist
into locked position.
NOTE: THE PHOTOCONTROL MUST CONTAIN A SOFT, RESILIENT GASKET FASTENED
TO THE BOTTOM SURFACE TO ASSURE A PROPER WEATHER SEAL BETWEEN THE
CONTROL AND THE RECEPTACLE.
MAINTENANCE
NOTE: A REGULAR MAINTENANCE SCHEDULE SHOULD BE FOLLOWED TO RETAIN
OPTIMAL LIGHT OUTPUT AND THERMAL PERFORMANCE.
Optical lens cleaning should be performed with a clean dry cloth to remove any
dust or other contaminants. Additional cleaning can be performed with non-abrasive
acrylic cleanser.
Remove any dirt, leaves or other foreign debris from the housing and fins.
Clean water may be used to flush the fins.
PIPE BRACKET INSTALLATION FIG. 3
TOOLS REQUIRED: 11/16" open wrench, drill.
STEP 1. Establish height and location for pipe bracket and luminaire.
STEP 2. Drill an 11/16” diameter hole through the pole.
STEP 3. Insert thru-bolt throught the pole, place square washer and nut on threaded
end of thru-bolt.
STEP 4. Slide slotted portion of the upper bracket behind the head of the thru-bolt,
tighten nut to draw bracket against pole.
STEP 5. Drive lag screws through the two holes in the lower bracket and tighten lug
screws and thru-bolt with wrench.
STEP 6. A ground lug may be included with pipe bracket. To install, insert carriage
bolt through square hole in the upper bracket.
STEP 7. Attach ground wire around bolt, assemble washer and nut and tighten with
wrench.
—CONTINUED
ADH130179
Customer First Center
1121 Highway 74 South
Peachtree City, GA 30269
P: 770.486.4800 F: 770.486.4801
www.cooperlighting.com
XNV LED
Area/Site Luminaire
Sheet 3 of 4
10/12/21 IMI-783
INSTALLATION INSTRUCTIONS
IMPORTANT: READ BEFORE INSTALLING FIXTURE.
RETAIN FOR FUTURE REFERENCE.
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible
contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufciently for user’s purpose, please contact
your nearest representative. NOTE: Specications and dimensions subject to change without notice.
FIG. 3
9-1/2" 10-5/8"
Thur-bolt, Nut and
Square Washer
18" or 24" Arm Length
(2) 7/8" Diameter Holes
for Lag Screws

ARM INSTALLATION (SQUARE POLE) FIG. 4
TOOLS REQUIRED: 1/2" open wrench, Phillips screw driver.
STEP 1. Insert nut plate into pole aligning holes on nut plate with mounting holes on
the pole.
STEP 2. Insert threaded rods through top and bottom holes and screw them into nut
plate.
STEP 3. Pull wires through center hole of back up plate and center hole of pole.
STEP 4. Make electrical connections between wires from pole and wires from the
fixture.
STEP 5. Align top and bottom holes on the arm to slide over threaded rods.
Arm should be ush to the surface of the pole.
STEP 6. Push washers over the threaded rods and screw on nuts.
STEP 7. Using 1/2" open wrench tighten nuts.
STEP 8. Pass cover plate over arm. Align set screw holes on the cover and the
arm and tighten set screw.
ARM INSTALLATION (ROUND POLE) FIG. 5
TOOLS REQUIRED: 1/2” open wrench, Phillips screw driver.
STEP 1. Insert nut plate into pole aligning holes on nut plate with mounting holes on
the pole.
STEP 2. Insert threaded rods through top and bottom holes and screw them into nut
plate.
STEP 3. With the rounded end of the adapter facing the pole, align the holes on the
adapter with mounting holes on the pole. Push adapter over threaded rods.
STEP 4. Pull wires through center holes nut plate, pole and adapter and make wiring
connections.
STEP 5. Align top and bottom holes on the arm to slide over threaded rods. arm
should be flush with the flat surface of adapter.
STEP 6. Push washers over the threaded rods and screw on nuts.
STEP 7. Using 1/2” open wrench tighten nuts.
STEP 8. Pass cover plate over arm. Align set screw holes on the cover and the arm
and tighten set screw.
ADH130179
Customer First Center
1121 Highway 74 South
Peachtree City, GA 30269
P: 770.486.4800 F: 770.486.4801
www.cooperlighting.com
XNV LED
Area/Site Luminaire
Sheet 4 of 4
10/12/21 IMI-783
INSTALLATION INSTRUCTIONS
IMPORTANT: READ BEFORE INSTALLING FIXTURE.
RETAIN FOR FUTURE REFERENCE.
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible
contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufciently for user’s purpose, please contact
your nearest representative. NOTE: Specications and dimensions subject to change without notice.
FIG. 5
Cover Plate
Arm
Nuts
Washers
Adapter
Threaded Rods
Backup Plate
Electrical Wires
Round Pole
FIG. 4
Cover Plate
Arm
Nuts
Washers
Threaded Rods
Backup Plate
Electrical Wires
Square Pole

ADH130179
Customer First Center
1121 Highway 74 South
Peachtree City, GA30269
P: 770.486.4800 F: 770.486.4801
www.cooperlighting.com
XNV LED
Area/Site Luminaire
Sheet 5of 5
10/12/21 IMI-783
INSTALLATION INSTRUCTIONS
IMPORTANT: READ BEFORE INSTALLING FIXTURE.
RETAIN FOR FUTURE REFERENCE.
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible
your nearest representative. NOTE:
Warranties and Limitation of Liability
Please refer to www.cooperlighting.com/legal for our terms and conditions.
Garanties et limitation de responsabilité
Veuillez consulter le site www.cooperlighting.com/legal pour obtenir les conditions générales.
Garantías y Limitación de Responsabilidad
Visite www.cooperlighting.com/legal para conocer nuestros términos y condiciones.
FCC Statement
Declaration of Conformity
Note: This equipment has been tested and
found to comply with the limits for a Class
A digital device, pursuant to part 15 of
the FCC Rules.These limits are designed
to provide reasonable protection against
harmful interference when the equipment is
operated in a commercial environment.This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruction
manual, may cause harmful interference
to radio communications. Operation of this
equipment in a residential area is likely to
cause harmful interference in which case
the user will be required to correct the
interference at his own expense.
Declaración de la FCC
Declaración de conformidad
Nota: Se ha probado este equipo y se ha
determinado que cumple con los límites
de la FCC. Estos límites están diseñados para
proporcionar una protección razonable contra
interferencias perjudiciales cuando el equipo
se opera en un entorno comercial. Este equipo
genera, utiliza y puede irradiar energía de
radiofrecuencia y, si no se instala y utiliza
de acuerdo con el manual de instrucciones,
puede causar interferencias perjudiciales en
las comunicaciones de radio. Es probable que
el funcionamiento de este equipo en un área
residencial cause interferencia perjudicial, en
cuyo caso el usuario deberá corregirla a su
propio costo.
Énoncé de la FCC
Déclaration de conformité
Cet équipement a été mis à l’essai
et déclaré conforme aux limites établies pour
Ces limites sont conçues pour assurer une
protection raisonnable contre tout brouillage
nuisible lorsque l’équipement fonctionne
dans un environnement commercial. Cet
équipement produit, utilise et peut émettre
de l’énergie radioélectrique et, s’il n’est
pas installé et utilisé conformément aux
instructions, il peut créer des parasites
nuisibles aux communications radio.
L’utilisation de cet équipement dans une
installation résidentielle est susceptible
de provoquer des interférences nuisibles,
auquel cas l’utilisateur devra corriger ces
interférences à ses propres frais.
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.