CORFLEX Lace Align User guide

APPLICATION INSTRUCTIONS
TLSO Version
Lace Align™
Spinal Orthosis
Adjusting and sizing the brace:
CORFLEX.COM 800 426 7353
A. Measure patient’s waist and hip circumference. If larger than 45” in
circumference, optional Extension Kit is required (sold separately).
B. Brace is preadjusted to t a 40" waist/hip circumference. If
adjustment is needed open brace and lay at.
C. Peel up edge of belt and slide until the desired length is achieved.
D. Fold belt end over and press to secure hook and loop closure.
Repeat for opposite side, both right and left must be adjusted equally
for proper brace performance.
A. Measure length from base of the neck (C7 vertebrae) to top of
sacrum to determine overall brace height.
B. Separate hook and loop closure between the back panel and harness,
as shown. Slide shoulder harness until desired back height is achieved.
C. Secure harness height by rmly pressing hook and loop fasteners
together.
The Lace Align TLSO Spinal Orthosis incorporates a back panel that is
preset at 5˚ of lordosis and can be adjusted using a heat gun. Adjustments
should be made by a therapist or orthotist trained in tting and molding
high temperature plastics.
1. Adjusting the back panel
2. Setting belt length
3. Setting shoulder harness height
A. Fabric cover must be
removed prior to adjusting.
Flexing/bending the back panel
will aid in removal and re-
application of the fabric cover.
B. Hold heat gun 3-5” from
the surface and apply heat to
the plastic side of the back
panel for 30-45 seconds,
moving the gun back and forth
continuously. Never apply heat
to the foam surface. Adjust
curvature as needed and hold
until cool (approx. 30 seconds).
C. Never mold the back panel
directly to the patient. Allow
to fully cool before reapplying
fabric cover.
1. Prior to each application make sure the brace is extended.
2. Place the pull-tabs 2” from each side of the back panel and pull the
ends of the belt away from each other to ensure it is fully lengthened.
Brace application
1. Preparing/resetting the brace
Brace comes preset at the second stitch line to t a 40"
circumference. Each stitch mark adjusts the circumference 5". .

UNIV
Lace Align - TLSO 35-3300
Sizing 25"- 45"
Extension Kit-16" 35-3904
1. Loosen both shoulder straps and slide brace onto shoulders, similar to
applying a backpack. Center the back panel on the lower back.
2. Slide ngers through the loops on the belt ends to aid application.
3. Wrap belt around abdomen and overlap ends, right over left. Press rmly
to engage hook and loop closure. When applied correctly, brace should t
snug at top and bottom. If there is a gap, reapply and angle ends to ensure
a snug t at upper/lower edges.
1. Slide thumbs through pull-tab holes and pull them away from the body.
Right pull-tab controls lower compression and left pull-tab controls upper
compression.
2. Apply tension until desired support is achieved.
2. Positioning and applying the brace
GM-5053-000
Care instructions:
Product should be hand washed only using warm water and detergent for
delicate fabrics, repeatedly rinsed and line dried only. Do not use bleach or
place in a dryer. Plastic/foam back panels can be cleaned using warm water
and a mild disinfectant. Do not immerse brace in liquids.
Caution:
This product has been designed and tested for single patient use only. It
should never be used by multiple patients. If additional pain or symptoms
occur while using the device, seek medical attention. Product should be
applied by a licensed or certied healthcare practitioner and as prescribed
by a physician or other qualied medical authority. Brace is not meant to be
worn during sleep or while bathing.
Indications:
Indicated for lower back pain, sprains/strains, kyphosis, decompressive
procedures, degenerative disc disease, bulging/herniated discs,
compression fractures, post-op stabilization, spondylolisthesis, spinal
stenosis, spondylosis, or severe DJD
Contraindications:
Contraindicated for unstable, displaced fractures, women who are
pregnant, persons with circulatory, pulmonary, cardiovascular or other
conditions where increased abdominal pressure could worsen risks.
Warranty:
Products manufactured by Corex are warranted to the original purchaser
against defects in workmanship and material for the life of the product. The
foregoing warranty shall not apply to normal wear and tear; or if the
product has been subjected to misuse or misapplication the warranty will
be voided at the discretion of Corex.
APPLICATION INSTRUCTIONS (cont’d)
CORFLEX, INC. 669 EAST INDUSTRIAL PARK DRIVE, MANCHESTER, NH 03109
WWW.CORFLEX.COM TOLL FREE: 800 426 7353 FAX: [phone]
To Reorder:
Designed for life.
Sizing: Fits waist circumference of 25” to 45”, use Extension Kit for circ. up to 70". .
Measurement taken from waist/hip circumference. Use larger of the two circumferences.
Product Number
Accessories
1. Sternum Strap improves comfort by pulling the shoulder straps away
from the axilla. Fasten buckle and tighten strap for a comfortable t.
2. Sternum Strap can also be removed completely if desired. Buckle is
slotted to facilitate removal/reapplication without cutting any strapping.
3. Adjust Shoulder Straps at top buckle (near axilla). Pull to tighten until
straps t properly and desired degree of spinal extension is achieved.
4. Straps should not be too tight as to cause discomfort or dig into axilla.
1. Wrap pull-tabs around the front of the brace, securing to loop on the
outside of the brace.
2. For comfort while seated, lessen tension on the upper portion of the
back panel (left pull-tab). Reapply tension upon rising.
3. When removing the brace, lift pull-tabs to release tension and
relocate them to the ready position as shown in Step 1.
3. Tightening the brace
4. Adjusting harness and sternum strap
5. Adjustment and removal