Costco Iris 2127023 User manual

IMPORTANT. PLEASE READ CAREFULLY AND RETAIN FOR FUTURE REFERENCE
If you experience any product malfunction, defect or are missing any parts,
please contact our customer service department at 1-855-586-8118 or
servicec @ taipengchina.com. Our hours of operation are Monday - Friday,
8:30 AM to 5:30PM EST.
Assembly Manual
10 ft x 20 ft / 3.05 m x 6.1m
Iris Curved Pergola
ITM./ART. 2127023
658 cm / 259.05 in / 259.05 po
609.6cm / 240.0in / 240.0 po
op25.29/ni25.29/mc832
306 cm /
120.47in /
120.47 po
1

SAFETY INFORMATION
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 3 hours.
Tools Required for Assembly (not included in the box):
For the best assembly and usage experience, please read through all steps before attempting to
assemble, operate or install the product
•WARNING:It is the consumer’s responsibility to comply with any building codes, ordinances,
zoning limitations, or local homeowner’s restrictions and obtain any required permit, before
purchase and installation of the products.
• WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS GAZEBO FABRIC.
This item meets the CPAI-84 flammability requirements. The fabric may burn if left in continuous
contact with any flame source. The application of any foreign substance to the tent fabric may
cause the flame-resistant properties ineffective.
• In the case of any high winds or high amounts of rain/snow, please remove the roof, clear the
snow from the roof immediately and check for damage before continuing use.
CAUTION
SET UP YOUR GAZEBO PROPERLY
• This product is heavy so do not attempt to assemble this item alone. For the best and safest
assembly experience, we recommend four (4) adults.
• Keep all children, pets and other obstructions away from assembly area.
• If any part is missing or damaged, do not attempt to assemble the product.
• In order to avoid damage to the gazebo and it's components, please use the appropriate tools.
• Do not use the structure as support.
• Check all bolts on a regular basis to maintain the sturdiness and safety of the structure.
• Keep instruction manual for future use.
• Do not climb on top of the gazebo. Falling off the gazebo can result in serious injury,
possibly even death.
EXAMINE YOUR GAZEBO
• Examine occasionally to ensure there are no loose parts.
• If loose parts are found, they should be retightened immediately.
Screwdriver Safety goggles
Hammer Gloves Stepladder
Hardhat Electric
drill
Percussion
drill
2

Components
A1 Post
Post
1
A2
A3
Post 1
2
B1 Upper Beam 12
B3
10
B2
1
C1 Back Beam 1
C2 Back Beam
C3 Back Beam
D1 Center Connector 1
Upper Beam
Upper Beam
1
1
3

Connector
Connector
Connector
Arched Beam
Arched Beam
Arched Beam
Arched Beam
Base Plate
D2 1
EConnector 12
Center Connector
F4
G6
K4
H2
I1 1
I2
J1
J2
1
1
1
4

Track
Sliding Tube
Sliding Tube
Base Cover
Inclined Strut
L4
P1 1
M1 1
Track
M2 2
Track
M3 1
O1
O3
2
8
Sliding Tube
O2
2
P2 1
Q2
1
Inclined Strut
Inclined Strut
5
Arched Beam
R
Sliding Tube
O4
2
Sliding Tube
O5
10

Connector
T24
S1
S2
4
4
U
Connector
Connector
Protective Cover 6
WGuide Pin 1
X1
X2
Roof
Roof
1
1
VProtective Cover 12
6
Y1 Connector 3
Y2 Connector 3

Hardware
Wrench
FF
10
(m6*95)
1
BB
JJ
304
NN
4
Bolt / Flat Washer
1
Bolt (m6*40)
Allen Wrench 5#
EE
20
Bolt / Flat Washer
1
AA
Nut / Flat Washer
10
Nut / Flat Washer
Allen Wrench
MM
10
QQ
Bolt / Flat Washer
(m6*15)
DD
1
Plastic Plug
HH
Sleeve
LL
2
PP
16
(m6*35)
Pipe Plug
CC
1
Allen Wrench 4#
Expansion bolt
GG
Allen Wrench
KK
20
OO
1
RR
SS
(m6*15)
1
Bolt / Flat Washer
22
Screw / Flat Washer
2
Bolt (m6*15)
7

A1/A2/A3
Fig1
Step1
A1/A2/A3
AA
AA
L
L
K
K
A1x1 A2x1 Kx4 Lx4 AAx8
1.Slide the Base Cover (L) over the Post (A1/A2/A3), then attach the Base Plate (K) to the Post
(A1/A2/A3) with bolts (AA), See Fig1.
A3x2
8

C1x1
Fx4
C2x1
C3x1 D1x1 Ux2 AAx30
Step2
C3
C3
C3 C3
F
F
F
C1
C1
C1
C1
C1
C1
C1
C1
D1
D1
D1
D1
C2
C2
AA
Fig2.1 Fig2.2
Fig2.4
Fig2.5 Fig2.6
Fig2.7
AA AA
AA
AA
AA
AA
AA
AA
AA
AA
UU
U
C3 C1
Fig2.3
AA
U
C1 C2
Fig2.8
AA
F
C2
C2
2.1.Insert one end of the Connector (F) into the Back Beam (C3) and fix it with bolts (AA), insert the other
end of the Connector (F) into the Back Beam (C1) and fix it with bolts (AA), and cover the Protective
Cover (U), securing it with bolts (AA), See Fig2.1-2.3.
2.2.Insert the Center Device (D1) into the Back Beam (C1) and fix it with bolts (AA), See Fig2.4-2.5.
2.3.Insert one end of the Connector (F) into theBack Beam (C2) and fix it with bolts (AA), insert the other
end into the Back Beam (C1), fix it with bolts (AA), and cover the Protective Cover (U), securing it with
bolts (AA), tighten all screws by now, See Fig2.6-2.8.
9

C3
C1
AA
AA
AA
AA
AA
AA
AA
AA
C2
Step3
B1 B3 B1
V
V
T
Fig3.2
Fig3.3
V
V
E
EE
B1
Fig3.1
C1
D1
Fig3.4
Fig3.5
B3
B3
B3
B3
B1
B1
B1
T
Fig3.6
B3 B1
Fig3.7
AA
AA
AA
V
V
B1x2 B3x1 Tx4 AAx22
Vx2
Ex2
B3 B1
Fig3.8
AA
AA
3.1.Connect the Connector (E) to the Upper Beam (B1) with bolts (AA), See Fig3.1
3.2. Insert one end of the Connector (T) into the Upper Beam (B1) and fix it with bolts (AA),cover the
ProtectiveCover (V), insert the other end of (T) into the Upper Beam (B3) and fix it and the Protective
Cover (V) with bolts (AA), See Fig3.2-3.3.
3.3. Insert the Center Device (D) into the Upper Beam (B3) and fix it with bolts (AA). See Fig3.4-3.5.
3.4. Insert one end of the Connector (T) into the Upper Beam (B1) and fix it with bolts (AA), cover the
Protective Cover (V), insert the other end of the Connector (T) into the upper beam (B3) and fix it with
bolts (AA), also fix the Protective Cover (V) with bolts (AA), See Fig3.6-3.8.
10
D1
B3
AA

E
AA
E
B1
Fig4.1
Step4
Fig4.2
Vx2
Ex10
T
V
V
V
B1 B2
T
Fig4.4
Fig4.3
AA
AA
B1
B1
B1
B1 B2
B2
B2
B2
AA
AA
AA
AA
V
V
B1x10 B2x10 Tx20 AAx90
4.1.Connect the Connector (E) to the Upper Beam (B1) with bolts (AA), See Fig4.1
4.2.Insert one end of the Connector (T) into the Upper Beam (B1) and fix it with bolts (AA), cover the
Protective Cover (V), insert the other end of (T) into the Upper Beam (B2) and fix it and the Protective
Cover (V) with bolts (AA). See Fig4.2- 4.4.
11

Step5
H
G
GG
G
G
G
H
I1
J1 J2
R
I2
H
Fig 5.1 Fig 5.2
AA
AA
AA
AA
I1 I1
J1 J1
U
Fig 5.3
I1 J1 G
G
G
Fig 5.4
AA
U
UU
U
U
AA
AA
J1
J1 J1
R
Fig 5.6
Fig 5.5
AA
AA
RR
U
G
G
Fig5.7 Fig5.8
AA
AA
AA
AA
J2 J2
RRU
AA
U
12

5.1. Insert one end of the Connector (G/H) into the Arched Beam (I1) and fix it with bolts (AA), insert
the other end of the the Connector (G/H) into the Arched Beam (J1) and fix it with bolts (AA), and
cover the Protective Cover (U), See Fig5.1-5.3.
5.2. Insert one end of the Connector (G) into the Arched Beam (J1) and fix it with bolts (AA), no need
to tighten it. Insert the other end of the Connector (G) into the Arched Beam (R), and fix it with bolts
(AA), and cover the Protective Cover ( U), See Fig5.4-5.6.
5.3. Insert one end of the Connector (G) into the Arched Beam (R) and fix it with bolts (AA) without
tightening, insert the other end of the Connector (G) into the Arched Beam (J2) with bolts (AA), then
cover the Protective cover (U), See Fig5.7-5.9.
5.4. Insert one end of the Connector (G/H) into the Arched Beam (J2) and fix it with bolts (AA), no
need to tighten it, insert the other end of the Connector (G/H) into the Arched Beam (I2), then cover
the Protective Cover (U), See Fig5.10-5.12.
Note: Be sure measurements diagonally across the overall frame are within 5mm of the same
distance after completing this step. TIGHTEN BOLTS.
I1x1 Rx1
Gx6
Hx2
I2x1
J1x1 J2x1 Ux4 AAx36
I2
G
H
Fig5.9 Fig5.10
AA
AA
AA
J2 I2
UJ2
R
Fig5.11
5875mm
AA
AA
J2 I2
Fig5.12
AA
J2 I2
UU
J2
I1 J1
R
13

6. Connect the Arched Beam （I1/I2/J1/J2 ）to the Post (A1/A2/A3) with bolts (BB).
See Fig 6.1- 6.2
BBx16
A1 A3
A3
A2
I1 J1
RJ2
I2
Step6
A1/A2
BB
BB
I1/I2
Fig6.1
A3
J1/J2
Fig6.2
14

7.1. Connect the Back Beam (C2/C3) and the Post (A1/A2) with bolts (AA), connect the Upper Beam
(B1) and Arched Beam (I1/I2) with bolts (AA), See Fig7.1-7.2.
7.2 Cover the Plastic Plug (LL), See Fig7.3-7.4.
AAx12 LLx16
A1
A3
A2
C3
B3
B1
B1
C1
C2
I1 J1 R
J2
I2
D1
Step7
A1/A2
B1
C2/C3
AA
Fig 7.1
C2/C3
B1
I2
AA
E
Fig 7.2
A1/A2
LL LL
I1/I2
Fig 7.3 A3
J1/J2
Fig 7.4
15

A1
A1/A2
A3
A3
A2
B3
B1
B1
B1
P1
P2
P1
C3
Q
C2
C3
Q
I1
I1/I2
AA
BB
J1
J2
I2
D
S1
S1
S1
S1
S2
S2
S2
Fig 8.1
Step8
16
A1/A2
B1
P1
I1/I2
Fig 8.2
LL

8.1 Connect the Inclined Struct (P1) to the Post (A1) and Back Beam (C3), use Bolt (BB/LL) to
connect the top part, use Bolt (AA) to connect the lower part，connect the Inclined Struct (P2) to
the Post (A2) and Back Beam (C2) by the same way, See Fig 8.1-8.2.
8.2 connect the Inclined Struct (Q) to the Post (A1/A2) and Back Beam (I1/I2) with bolts (AA),
See Fig 8..3
8.3Connect the Connector (S2) to the Posts (A1/A2/A3) and Arched Beams (I1/I2/J1/J2）
with bolts (AA)，connect the Connector (S2) to the Post (A3）and Arched Beam (J1/J2)
See Fig 8.4-8.5.
A3
P1
Q
J1
S2
AA
Qx2 S2x4
S1x4 AAx60
P1x1 P2x1
17
Fig 8.3
Fig 8.4 Fig 8.5
A1/A2
AA
C3
J2
AA
AA AA
A3
J1/J2
BBx4 LLx4

9.1. Insert the bolt (DD) into the hole of the Center Connector (D1) with Nut (NN), See Fig 9.1,
9.2.Connect the Upper Beam (B2) and the Center Connector (D1) with bolts (AA), and connect the
Upper Beam (B1) and the Arched Beam (I1/I2/J1/J2/R) with bolts (AA). See Fig 9.2- 9.3.
AAx40 DDx10
A1
A3
A3
A2
B1
B2
B1
B1 I1
J1
R
J2
I2
D1
D1
D1
B1 I1/I2/J1/J2/R
E
AA
AA
DD DD
Step9
Fig9.2
Fig9.1
Fig9.3
B2
NN
NNx10
18

M2
I1
J1 R
J2 I2
Step10
M2 M3
M1
19
HH
HH
M1/M2/M3
I1/I2/J1/J2/R
Fig10.2
10.1 Connect the Connector (Y1) and the two adjacent tracks (M1/M2/M3)to the Arched beam at
the same time, and fix it with bolts (HH). Fix the other end of the track (M1/M3) to the beam with
bolts (HH). Don't tighten the bolts.
10.2 Fix the Connector (Y2) to the arched beam with bolts (HH). Don't tighten the bolts.
Note: After the junction of the two rails closing up and aligning, then tighten all bolts.
Fig10.1
HH HH
I1
M1 M2
M2
M3
J1 R
J2
I2
HH
M1/M2/M3
HH Y2
Y1
M1/M2/M3
M1x1
M2x2
M3x1
Y1x3 Y2x3 HHx22

EE
A1
A3 A3
A2
Fig11.2
Fig11.1
Fig11.3
O1
O1
O1
O2
O5
O4
O2
O5
O3
O1
O2
O3
X1/X2
X1/X2
X1/X2
X1
X2
X1/X2
Step11
Fig11.4
Fig11.5
O1/O2
C1/C2/C3
20