Costway BB0487 User manual

Baby Rocker
BB0487

Please read all instructions carefully and keep it for future reference.
General Warnings:
Attention: To prevent possible injury by entanglement, remove this toy when the child starts
trying to get up on its hands and knees in a crawling position.
Danger! Keep all small parts and packaging materials for this product away from babies and
children, otherwise they may pose a choking hazard.
The product must be installed and used under the supervision of an adult.
Read through each step carefully and follow the proper order.
Remove all Packaging, separate and count all parts and hardware before Installation.
Please ensure that all parts are correctly installed, incorrect Installation can lead to a Danger.
We recommend that, where possible, all items are assembled near to the area in which
they will be placed in use, to avoid moving the product unnecessarily once assembled.
Ensure a secure surface during construction, and place the product always on a flat, steady
and stable surface.
02 07

Cross Brace 2 Retainers with Lock Nut
2 Side Rails
Pad Seat Back Tube 2 Feet Vibrations Unit
KickstandToy Bar
Button battery
INCLUDED
Battery
NOT INCLUDED
Manual for battery installation
and Notice for battery usage
Find the battery box on top of the vibration device.
Loosen the screw in the cover plate and open it.
Put in 2 1.5V AA alkaline batteries. Cover the plate back and tighten the screws.
If there is abnormal circumstance you may need to reopen power.
Turn off the power source and turn it on again.
Important! Low battery can cause error: no vibration or fail to turn off. Remove
and dispel batteries and replace them with 2 new 1.5 AA alkaline batteries.
Hint: We recommend alkaline batteries for longer
useful life.
Find the battery box on the toy banister. Loosen the screw in the cover plate and open it.
Dispel used batteries and replace with 3 new alkaline button batteries.
Cover the plate back and tighten the screws.
When voice or light is fading out, adults need to replace the battery.
1. The rocking chair uses two pieces
1.5V "AA" batteries, Sunflower toys
use 3 pieces 1.5V button batteries.
2. How to remove and insert the
batteries（Look at the picture on
the right）.
3. Non-rechargeable batteries are not
to be recharged.
4. Rechargeable batteries are only to
be charged under adult supervision.
5. Rechargeable batteries are to be
removed from the toy before being
charged.
6. Different types of batteries or new
and used batteries are not to be
mixed.
7. Only batteries of the same or
equivalent type as recommended are
to be used.
8. Batteries are to be inserted with the
correct polarity.
9. Exhausted batteries are to be
removed from the toy.
10. The supply terminals are not to be
short-circuited.
Multi-Function Baby Rocking Chair Operating Instructions
It is strongly recommended to keep the instructions.
Please read the instructions carefully before installation and operafion .
Applicable Age: 0-36months (No heavier than 18kgs)
Pictures on the packaging may be a little different from the real obieck, please keep the real
object in prevail.
03
Restraint Belt Restraint Belt
Restraint Pad
Kickstand
Rotate the kickstand out.
Push down on the seat bottom to be sure the kickstand
is in position.
WARNING:
1. To avoid choking, please dispose plastic bags
or keep them away from babies and children.
2. Caregivers should not leave when baby is seated.
3. It is very dangerous to use recliner on high plane
above floor (like decks)
4. Recliner is unsuitable for long time sleep.
5. Always apply restrain system.
6. Do not drag recliner with the toy stick.
7. No more use for the recliner when your baby can
sit by himself/herself.
8. This product contains small parts which can hurt
or cause choking. No use for children until
assembled.
9. Attached toys should be taken out by adults,
and play by children in adults’ custody.
10. Do not stand on the recliner to avoid falling.
11. Using this product as transportation facility or
elevator with baby sitting in it is forbidden.
12. Use chair mode instead of recliner mode when
children can sit straight.
13. Packages are not toys.
Do not play with them to
avoid danger.
Securing Your Child
Place your child in the seat. Position the restraint pad
between your child’slegs. Fasten the restraint belts to each
side of the restraint pad.
Make sure you bear a “click” on both sides.
Check to be sure the restraint system is securely attached
by puling it away from your child.The restraint system
should remain attached.
Pull
Power
Switch
Fit the plugs on each end of the toy bar into the sockets in
each side rail.
Hint: The toy bar is removable. Press the ends of the
latches and lift the toy bar.
Make sure your child is properly secured in the seat.
Slide the power switch to the ONposition for calming vibrations.
Slide the power switch to the OFF position to turn vibrations off.
Pull the ring for a short tune!
06

Foot Side Rail
Assembly
Lift the top of the foot to fit the peg into the hole in the side rail
.
Hint: Each foot is designed to fit the side rails one way.
If a foot does not seem to fit, remove it and assemble it to
the other side rail.
Repeat this procedure to assemble the other foot to the
other side rail.
Slide the socket on a foot onto the tapered end of a side rail.
Position each side rail so that the button faces outward.
While pressing the tabs on the ends of the seat back tube,
insert it into the sockets in each side rail,
until the tabs “Snap” into place.
Make sure you hear a “snap” on each side.
Pull the seat back tube up to be
sure it is secure in the side rail
sockets.
Seat Back Tube
Side Rail Sockets
Button
Press Tabs
IMPORTANT! Before assembly and each
use. inspect this product for damaged
hardware, loose joints, missing parts or
sharp edges.
DO NOT ues if any parts are missing or
broken.
M5x32 mm screw-2 M5x50 mm screw-2
M5x42 mm screw-2M5 locknuts-2
04
Insert the ends of the kickstand into the socket in each foot.
Kickstand
Vibrations Unit
Cross Brace
.
Fit the cross brace between the side rails, as shown.
Hint: The cross brace is designed to fit one way.
If it does not seem to fit, turn it around and try again.
Lift
Press Button
UPRIGHT
Press Button
RECLINE
Lower
SeatPosition
Upright: While pressing the button on each side rail,
lift the seat back.
Recline: While pressing the button on each side rail,
lower the seat back.
Buckle up the back of the pad and the stull.
Make sure you hear a clatter.
pocket
05
With the vibrations unit facing forward, fit the notches on
the unit onto the side rails, as shown.
M5x42 mm screw-2
M5 locknuts-2
M5x32 mm screw-2
M5 locknuts-2
M5x50 mm screw-2
M5 locknuts-2