Costway SP37328 User manual

USER'S MANUAL
48” 3in 1 Multi-game Table
SP37328

1
910 11 12
13 14 15 16
2 3 41
x2
6 7 85
x13 x13 x16
x16 x8 x8 x2
x1
18 19 20
x2 x2 x1
21
x2
22
x2
23
x4 x4
24
x2
x2
25
x8
26
x1
27
x3
28
29
x2
30 31
x2
17
x2
SP37328 PARTS LIST
End Apron Soccer Playfield
Hockey Goal
Support Brace
5-Hole Rod 3-Hole Rod 2-Hole Rod
Goal Box-Top
Goal Box-Bottom
Player - Red
x1
Hockey Playfield
Player - Ivory
Side Apron
x2
Rod Washer
Rod End CapFoam Bumper Handle
Felt Pad
Pusher Round Puck
x1
Billiard Mainframe
Bottom Locking
Clasp
Top Locking Clasp Billiard Ball Set
Brush
Cue
x1
Triangle
Chalk Soccer Ball
x2
Leg Panel
x1
x4
Leg
32
x4
Leg Leveler

2
x14
Allen key
A1 A2 A3
x16x16
SP37328 PARTS LIST
x12 x26
4x12mm Screw
P1 P2
x4
P3 P4
x2
SP37328 PRE-INSTALLED PARTS
Plastic Rod
Bushing
Plastic Ball
Entry Rim
5/16″T - Nut
x6
Pocket
x16
P5 P6
x2
P7
x16
1/4″T - Nut
Side Pocket Cap Corner Pocket Cap
x4
A7
A4
A5 A6
x24
1/4'' x 1-1/8'' Bolt
x1
1/4″ Washer
3x12mm Screw3x18mm Screw
4x35mm Screw
ASSEMBLY INSTRUCTIONS:
1. Find a clean, level place to begin the assembly of your Multi Game. The table will be assembled upside down and
then turned over on its legs once the assembly is completed. This game table is heavy, and turning it over will require
at least two strong adults.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the parts list pages.
Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work surface.
x8
4x15mm Screw
A8

3
FIG.1
FIG.1
3. Attach the Legs (#7) to the Billiard Mainframe (#1) using four Bolts (#A2) and four Washers (#A3) per Leg.
4. Screw the Leg Levelers (#33) into the bottom of each Leg.
1
7
33
A2
A1
X 1
X 4
X 4
X 1
X 16
A3
X 16
P7
X 16
P4
X 6
P1
X 4
A2
A2
7
1
33
7
7
7
A3
A3
P7 P4
P1
1
7

4
CAUTION: Two strong adults are recommended to turn the table over as shown.
1. Life the table off of the ground.
2. Turn the table over.
3. Place it on all four feet at the same time on the ground.
FIG.2
5. Attach the Leg Panels (#8) to the Legs using four Screws (#A8) per Leg Panel. See FIG. 2.
6. Lift the table assembly from the floor with two strong adults, turn it over, and set table on its legs in the location
where you play. See FIG. 2A.
Go back and make sure that all connections are tight.
DO NOT LEAN THE
TABLE ON ITS LEGS
HOLD TABLE
HOLD TABLE DO NOT HOLD THE LEGS
FIG.2
A8
X 8
P5
X 2
P6
X 4
8
X 2
6
7
7
7
A8
7
8
8
FIG.2A
P6
P5

5
FIG.3
7. Attach two Side Aprons (#6) to the one End Apron (#2) using four Screws (#A4). See FIG. 3.
Note: Do not tighten the Screws at this step.
8. Slide the Soccer Playfield (#3) (drawing upside-down) into the grooves of Side and End Aprons (#6 and #2).
Note: Make sure the Soccer Playfield slide into the right groove.
FIG.4
9. Place the Support Braces (#5) on the Soccer Playfield (#3), and then attach them to the Side Aprons (#6) using two
Screws (#A4) per Support Brace. See FIG. 4.
FIG.3
A4
X 4
6
X 2
2
3
X 1
X 1
FIG.4
A4
3
6
62
A4
The groove for Hockey Playfield
The groove for Soccer Playfield
5
A4
X 3
X 6
A4
6
6
2
5
53

6
FIG.5
10. Slide the Hockey Playfield (#4), with graphics facing up, into the grooves of Side and End Aprons (#6 & #2).
See FIG. 5.
FIG.5
FIG.6
11. Attach the other End Apron (#2) to the Side Aprons (#6) using four Screws(#A4). See FIG. 6.
12. Attach the Hockey Goals (#9) to the Hockey Playfield (#4) using two Screws (#A5) per Hockey Goal.
See FIG. 6A.
13. Tear off the back side papers of the Felt Pads (#19) and stick them at the bottom of the Pushers (#18).
See FIG. 6B.
FIG.6
2
A4
X 1
X 4
A5
X 4
9
X 2
18
X 2
19
X 2
A4
6
2
A4
4
2
9
A5
18
19
19
FIG.6A
FIG.6B
4
X 1
3
6
6
2
4

7
FIG.7
14. Turn the Soccer Table (See FIG. 6) over and then place it on the top of the Billiard Mainframe (#1).
15. Attach the Top and Bottom Goal Boxes (#16 and #17) to the End Aprons (#2) using two Screws (#A5) per Goal Box.
16. Attach the Top Locking Clasps (#25) to the Soccer Side Aprons (#6) using two Screws (#A7) per Top Locking Clasp.
Attach the Bottom Locking Clasps (#24) to the Billiard Mainframe (#1) using two Screws (#A7) per Bottom Locking
Clasp. See FIG. 7A.
16
17
X 2
X 2
A7
X 24
A5
X 8
FIG.7
24
25
X 4
X 8
16
17
A5
25
24
24
A7
A7
25
2
6
1
FIG.7A

8
Note: Players of the same team color should
have Handles (#15) on the same side, and each
team’s players should be facing their opponent.
22
22
22
22
21
21
23
23
= Red
= Ivory
ORDER OF PLAYERS
(Overhead View)
FIG.8A
FIG.8
FIG.8
17. Slide the Rods (#21, #22 and #23)) through the Rod Bushings (#P2) on one Side Apron (#6) in the order as shown in
Fig. 8A and 8B.
Note: The Rods have a hole at the end where their Handles will go.
18. Place the Rod Washers (#12), Foam Bumpers (#13) and Players (#10 and #11) onto the Rods (#21, #22 and #23) in
the order as shown in Fig. 8, 8A and 8B.
19. Now insert the Player Rods (#21, #22 and #23) through the Rod Bushings (P2) on the opposite Side Apron (#6).
20. Attach the Players (#10 or #11) to the Rods (#21, #22 and #23) using one Screw (A6) per Player. See FIG. 8C.
Note: The goalie should be at the left side of each player.
21. Place the Handles (#15) onto the ends of the Rods (#21, #22 and #23) with the holes. Then place the Rod End Caps
(#14) onto the other side of the Rods. See FIG. 8.
11
12
13
X 13
10
X 13
X 16
X 16
14
X 8
15
X 8
21
22
23
X 2
X 4
X 2
A6
X 26
P2
X 2
P3
X 16
10 11
or
A6
FIG.8C
FIG.8B
P2
P2
12
12
13
22
13
10 11
or
P3
15
14
Handle Hole
6

9
DI RECT IONS FOR PLAYI NG V ARIOUS GAM ES
1) Billiard - Play the game as assembled using the Billiard Ball Set (#26), Cue (#27), Triangle (#28).
2) Soccer - Place the Soccer table on the top of the Billiard Frame. Play the game using the Soccer Ball (#31).
3) Glide Hockey - Reverse the Soccer table and then place on the top of the Billiard Frame. Play the game using
Pushers (#18) and Hover Pucks (#20).
YOU ARE NOW READY TO PLAY!
Soccer
Hockey
Billiard