Country Living WT-KD1422N User manual

RIGHT LEG
LEFT LEG
PARTS LIST
Description
A
Parts List
Parts No. QTY
DescriptionParts List
Parts No.
QTY
VENDOR CODE #: WT-KD1422
MADE IN CHINA
ADIRONDACK CHAIR
ASSEMBLY INSTRUCTION
ASSEMBLY INSTRUCTION
ASSEMBLY INSTRUCTION
ASSEMBLY INSTRUCTION
P.01
READ & SAVE THESE INSTRUCTIONS:
Examine all packing material before assembling, shortages
may occur from parts left in the packing material.
Please follow below instructions to assemble step by step.
B
1
2
3
1PC
1PC
C1PC Washer
5/16”* 23mm*1.5mm
12PCS
4
5
6PCS
4PCS
BOLT
1/4”*2”
D1PC
SEAT
BACK
SUPPORT
E1PC
MIDDLE BACK
BAR 1PC
RIGHT ARM
LEFT ARM 1PC
WOOD SLAT 1PC
F
G
H
Nut
5/16”
6PCS
SCREW
8*1-1/4”
11PCS
BOLT
5/16”*2-1/2”
6
PHILLIPS HEAD
SCREWDRIVER IS
REQUIRED (NOT
INCLUDED)
Washer
1/4”* 19mm*1.0mm 4PCS
9
8
7Hexagonal
Wrench 2PCS
1PC
Y Wrench

3
1
Attach right leg C and left leg D to the seat A,
then insert bolt #2 with washers #3 & nut #5 by
P.02
2Attach wood salt H to
right leg C and left leg
D , insert the screws #6 by using phillips head
screwdriver
#9 to tighten, as shown in the
diagram.
H
3
5
8
A
C
D
6
9
C
D
6
9G
B
4
1
7
B
A
2
7
3
4
using Hexagonal wrench #7 and Y wrench #8
to tighten, as shown in the diagram.
Attach middle back bar G to back support B,
then insert the screws #6 by using phillips
head screwdriver #9 to tighten, as shown in the
diagram.
Attach the bottom bar of back support B ( as the
step 3 previous assembled part ) to the back bolt
hole of seat A, then insert bolts #1 with washer #4
by using Hexagonal wrench #7 to tighten, as
shown in the diagram.

P.03
6
5
Attach the right arm E and left arm F to above previous assembled part, insert bolts #1 with
washers #4 and insert the bolt #2 with washers #3 & nut #5 by using Hexagonal wrench #7
and Y wrench #8 to tighten, as shown in the diagram.
B
F
D
E
C
14
3
532
8
7
7
G
Check all the hardwares are fully tightened and this adirondack chair is ready for your use.

P.04
CARE & MAINTENANCE
Wood is a living material that continues to respond to climate condition even after
being made into a piece of furniture. Left untreated, the wood will weather to a
silvery grey.
To reinforce its weatherproof ability, this furniture was treated with outdoor
Polyurethane paint finish at the factory. Before using, wipe the finish with a clean &
dry cloth lightly to obtain a more clean & shiny surface.
During normal weathering, wood may crack slightly due to changes in the moisture. This
does not affect the structural integrity of your furniture. Manufacturer recommends
periodic application of furniture polish or Polyurethane paint acquired from most
paint store & home center that will ensure the wood furniture is protected and its
appearance maintained.
As wood is a living product, you may find that you need to tighten any fittings
periodically.
Exercise care when using the wood furniture to prevent excessive scratching.
Bring your furniture inside during inclement weather & cover it while not in use.
CUSTOMER AFTER SERVICE
Contact our customer service department with a description of the problem at 1-877-2
51-5558 or email us at psiservic[email protected] between 9:00am and 4:00pm Pacific Coast
Time Monday through Friday. WEBSITE AT www.psiglobal.com