Craftsman BACKWALL WITH METAL PEGBOARD User manual

BACKWALL WITH METAL PEGBOARD
CAUTION: Backwall MUST be attached to the Workbench before the
top is attached and the drawers are installed.
CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA. F1493

fSAFETY WARNINGS AND CAUTIONS:
Use appropriate safety equipment when using power and hand tools. Failureto do so may cause personal injuryor productdamage.
Use adequate manpower when assembling and moving this unit. Failure to do so may cause personal injuryor productdamage.
DO NOT stand onthis product.You may fall which may cause personal injury.
DO NOT mount this producton a truck bed or any other movingobject.This may cause personal injuryor productdamage.
Appropriatelysecure this product before moving itwith a forklift.
DO NOT tow with power equipment. The productcould tip, which may cause personal injuryor product damage.
DO NOT alter this product inany manner. This may cause productdamage or personal injury.
Keep the producton level surfaces. The product may become unstable and tip ifstored or moved on an un-level surface,which may
cause personal injuryor productdamage.
Be sure the workbench isflat on the floor before installingthe Workbench Backwall. Failure to do so may cause personal injuryor
productdamage.
The maximum weight allowed to hang on or be in any way supported fromthe backwall is65 pounds. Ifthe limit is exceeded the
productmay tip and cause personal injuryor productdamage.
Be sure to secure the Workbench Backwall to a studded or concrete wall. Failure to do so may cause the Workbench Backwall and
Workbench to become unstable and tip. This may cause personal injuryor product damage.
Use only the providedpegboard on Workbench Backwall.
Backwallwith Metal Pegboard is onlyto be attached to one ofthe following Workbenches: 59741, 59742, 59746. Failure to doso
could resultin personal injury or productdamage.
4
r
Tools Required:
Socket Wrench
7/16" Socket
Dnll
3/32" DrillBit
1/8" DrillBit
Screwdriver, Phillips
Screwdriver, Flathead
Hardware Included:
_[_ AA (16) _--_) DD (16)
BB (3) _EE (16)
CC (2) FF (2)
GG (1)
(_,all 1-800-4MY-HOME for Service Parts.
(1-800-469-4663) Refer to Service Parts Drawing for full listing of Service Parts._

E
A(2)
G\\
F
\\
H
..... :!:!:i:!::'
\\\\\\,B(2)
D
C(2)
)

f
WARNING: Backwallwith Metal Pegboard isonly to be
attached to one of the following Workbenches:
59741, 59742, 59746
NOTE: To assemblethe Backwall,the drawers and top must
first be removed from the workbench.
DRAWER REMOVAL AND INSTALLATION:
FRICTION DRAWERS:
• Emptythe drawer.
•Fullyextend the drawer. Then push it back a fraction of
an inch.
•Insert a screwdriverintothe slot in the slide and
depress the stop untilit clears the lance.
Slot f Stop
Lance
Lubricate
Repeat the procedure for the other slide. Remove the
drawer.
To reinstallthe drawer, prythe stop far enough out to
engage the lance(3/16" to 1/4")and push the drawer
onto the slides untilthe stops pass over the lances.
BALL BEARING DRAWERS:
Empty the drawer.
• Fully extend the drawer.
•Liftthe release lever on the rightside, while depressing
the leveron the leftside and pullthe drawer out to
remove.
Lever
•To reinstall, carefullyalign the slides and slowlypush
the drawer intothe unituntilthe drawer stops.
TOP REMOVAL:
NOTE: When removing top, save the screws to reattach after
backwall isassembled.
Remove and save the screws from the wood top.
Remove top fromworkbench base.
f
STEP1
AA (2)
DD (2)
EE (2)
Remove and reuse topfastenersinback of
workbench.
Attach A(2).
Fingertighten.
__ Existing
hardware
/
/
FRONT
A(2)
J

F
STEP2
BB {I)
• Attach B(2) and C(2).
Finger tighten.
AA
Back
/DD EE
/
Front
©
BB
Back
Wrench Tighten
fasteners from
step 1
DD (8)
EE (S)
F
STEP 3
©
Assemble tray.
Fingertighten.
EE
R, \
AA(2)
BB (2)
DD (2)
EE (2)
DD
AA
/
]
/
/
E
J

AA (4)
DD (4)
\\ j
EE (4)
Install tray_
Finger tighten.
DD
EE
AA
\
Back
i
/
Front
NOTE: To reattach the top, new pilot holes willneed to be
marked and drilled.
Back
Reattach top
with existing
hardware
/
/
¢
Front
Place top on the bench in the desired location.
• Mark centers ofmounting holesto be drilled.
• Drill 1/8" pilot holes in top.
• Reattach top usingexisting hardware.
•Wrench tighten all fasteners.
J

f
STEP 5 Continued
CC (2)
Drill (2) 1/8" pilot holes in top using holes in C(2) as a
template.
Attach using CC(2).
Back
\CC Fmnt
Reinstall drawers.
J
F
STEP6
(_._:_ FF (2) GG (1)
Install grommet (GG) indesired location.
Place electrical cord for G through grommet.
Place G against bottom oftray.
Attach using FF(2).
Place elecldcal /
cordthrough
grommet.
hole
_'-MounUng hole
Screws and
washers
supplied
with H
Place H as desired.
Mark centers of4 holes to be drilled.
Drill (4) 3132"pilot holes 1t2" deep.
Attach H using (4) screws and washers provided.
r• Periodicallythe surfaces should be cleaned with amild
detergent and water.
•Auto wax will preserve the unit's luster finish. Apply the
wax as to acar. The wax will also help protect the unit
against scratches.
•Grease and oil can be removed withmost standard
cleaning fluids. For safety, use a nonflammable cleaning
fluid.
J

MANUAL DE USUARIO
TABLERO METALICO TRASERO
ADVERTENCIA: Asegdrese de colocar el tablero
antes que la tapa y los cajones.
ATENCION: Lea y siga todas las Normas de Seguridad y las Instrucciones de Funcionamiento antes
de utilizar por primera vez este producto.
Sears, Roebuckand Co., Hoffman Estates, IL 60179, USA. F1493

PRECAUCIONES DE SEGURIDAD:
f
Cuando trabaje con electricidad o herramientas manuales, utiliceun equipo de seguridad adecuado. Una averia puede causar daSos
personales o materiales.
Aseg_rese de utilizarlas herramientas y piezas adecuadas cuando este montando o moviendo el producto. Una averia puede
producirdatlos personales o materiales.
NO se coloque encima del producto. Puede caerse y da_arse.
NO coloque el pmducto ni en una caravana ni en cualquier medio de transporte. Esto podrfa causar daCiospersonales o daflar el
producto.
Antes de movedo con una carretilla elevadora, aseg0rese de colocarlo adecuadamente.
NO Ioarrastre con un equipo el_ctrico. Elproducto puede volcar y causar da_os personales o dafiar el producto.
NO modifique el productode ninguna manera. Esto podrfa causar dar_ospersonales o daflar el producto.
Mantenga el productoen superficiesplanas. El producto puede ser inestable sise coloca o se mueve en una superficieque no sea
plana, Io que podrtacausar dahos personales o daSar el producto.
AsegOrese de que el banco de trabajo este biencolocado en el suelo antes de instalar la parte de atr_s del tablero. Si no Io hace,
puede sufdrdattos personales o dar3arel objeto.
The maximum weight allowed to hang onor be in any way supported from the backwall is 65 pounds. Ifthe limit isexceeded the
product may tipand cause personal injuryor productdamage.
AsegOrese de que el tablero del bancoest_ atornillado a un pilaf o a una pared de camento. Si esto nose realiza adecuadamente, el
tablem trasero o el banco de trabajo puedenser inestables o caerse. Esto pedrla causar dar3ospersonales o dafiar el producto.
$61o utiliceel tablero que viene con el bancode trabajo.
El tablero met_lico trasero s61ose puede colocar en lossiguientes modelos de bancos: 59741, 59742, 59746. De Io contrariopedda
ocasionarse lesiones personales o da_ar el producto.
Herramientas necasarias:
Trinquete
Llave de tubo de 7/16"
Talladro
Brocade 3/32 de pulgada
Brocade 118de pulgada
Destomillador,philips
Destomillador,de cabeza plana
Ferreteria incluida:
BB (3) _ EE (16)
CC(2) !_ FF(2)
GG (1)
(Llame al 1-800-659-7084 para Piezas de $ervicio.
Consulte el dibujode piezas de servicio sidesea un listado completo de piezas de servicio, )