Craftsman 486.24560 User manual

Operator's Manual
CRRFTSMRH°
10-iNCH MOLDBOARD PLOW
Model No. 486.24560
DO NOT RETURN TO STORE
For Missing Parts or Assembly
Questions Call 1-866-576-8388
'\\ \
\\\\\\\\\\\
o \
CAUTION:
Before using this product, read
this manual and follow all Safety
Rules and Operating Instructions.
,, Safety
,, Assembly
,, Operation
,, Maintenance
,, Parts
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com/craftsman
PRINTED IN U.S.A. FORM NO. 49070 (03/03/09)

SAFETY ........................................................................... 2
WARRANTY .................................................................... 2
CARTON CONTENTS ..................................................... 3
FULL SIZE HARDWARE CHART .................................... 4
ASSEMBLY ...................................................................... 6
OPERATION .................................................................... 7
SERVICE AND ADJUSTMENTS ..................................... 8
MAINTENANCE .............................................................. 9
TROUBLESHOOTING ................................................... 10
REPAIR PARTS LIST ..................................................... 11
PARTS ORDERING/SERVICE ...................... BACK PAGE
• Read the tractor and 10-Inch Moldboard Plow
owner's manuals and know how to operate your
tractor before using tractor with this attachment.
Never operate tractor and attachment without wearing
substantial footwear and proper clothing.
This attachment contains sharp edges, always wear
gloves when handling or working with the attachment.
Never allow children to operate tractor and snow
blade and do not allow adults to operate without
proper instructions.
Keep others away from area in which you are
working, especially small children and pets.
Inspect the area that you will be using the tractor
and attachment first and mark out any holes or other
hazards.
Maintain tractor and attachment as detailed in their
owner's manuals.
Stay away from creeks, ditches and public highways.
If an object is struck, immediately stop tractor
and inspect tractor and attachment. Repair any
damage found before continuing use of tractor and
attachment.
Always begin transmission in first (low) gear and
gradually increase speed only when needed.
CRAFTSMAN FULL WARRANTY
When operated and maintained according to all supplied instructions, if this Craftsman product fails due to a defect
in material or workmanship within one year from the date or purchase, return it to any Sears store or other Craftsman
outlet in the United States for free replacement.
This warranty applies for only 90 days from the date of purchase if this product is ever used for commercial or rental
purposes.
This warranty does not include items considered to expendable parts that can wear out from normal use within the
warranty period.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179
DO NOT RETURN TO STORE for Missing Parts or Assembly Questions
Call 1-866-576-8388 Attachment Hotline
The model number and serial numbers will be found on a
decal attached to the 10-Inch Moldboard Plow.
You should record both the serial number and the date of
purchase and keep in a safe place for future reference.
MODEL NUMBER:
SERIAL NUMBER:
DATE OF PURCHASE:
486.24560
2 Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE

7
REF QTY DESCRIPTION REF QTY DESCRIPTION
1 1 Crank 7 1 Coulter Blade
2 2 Half Beam 8 1 Landside
3 1 Moldboard 9 1 Hitch Bracket
4 1 Standard 10 2 Adjustment Bracket
5 1 Coulter Standard 11 1 Coulter Fork
6 1 Coulter Hub 12 1 Threaded Tube
Call 1-866-576-8388 for missing parts or assembly help 3
DO NOT RETURN TO STORE

/
25
3O
26
31 34
32
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
18
/
28
/
35\
NOT SHOWN FULL SIZE
I°l
I
36
,/
38
,/
4 Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE

REF QTY DESCRIPTION REF QTY DESCRIPTION
13 1 Plow Bolt, 1/2 x 2" 26 2 Washer, 5/8"
14 2 Plow Bolt, 3/8" x 1" 27 1 Cotter Pin, 1/8 x 1-1/4"
15 2 Spacer, 5/8"x 1/2" 28 2 Hex Bolt, 1/2 x 1-1/2"
16 1 Spacer, 5/8" x 5/8" 29 3 Carriage Bolt, 5/16 x 3/4"
17 3 Washer, 5/16" 30 4 Hex Nut, 5/8"
18 1 Hex Bolt, 1/2 x 1-3/4" 31 2 Hex Nut, 1/2"
19 3 Lock Nut, 5/16" 32 3 Lock Nut, 1/2"
20 2 Hex Nut, 3/8" 33 2 Lock Nut, 5/8"
21 1 Roll Pin, 5/16 x 1-3/4" 34 2 Hex Bolt, 5/8 x 2"
22 1 Square Nut, 1/2" 35 1 Coulter Axle
23 1 Washer, .5312 x 1.0625 x .09" 36 1 "U" Bolt, 5/8"
24 2 Carriage Bolt, 1/2 x 1-1/2" 37 1 Coulter Clamp
25 1 Spacer, 1/2"x 9/16" 38 1 Trunnion
Call 1-866-576-8388 for missing parts or assembly help 5
DO NOT RETURN TO STORE

TOOLS REQUIRED FOR ASSEMBLY
1 - 10" Adjustable Wrench
1 - 15/16" Wrench
1 - 13/16" Wrench
1 - 3/4" Wrench
1 - 1/2" Wrench
1 - 9/16" Wrench
1 - Pliers
1 - Gloves
• Remove the loose parts and the hardware packages
from the carton. Lay out all parts and hardware and
identify using the illustrations on pages 3 and 4.
NOTE: Right hand (R.H.) and left hand (L.H.) are
determined from the operators position while seated on
the tractor.
NOTE: Carefully follow directions for when fasteners are
to be tightened.
STEP 2: (SEE FIGURE 2)
Slide trunnion through holes in adjusting brackets.
Insert crank through hole in side of trunnion, spacer,
two 5/8" nuts and then thread into threaded tube.
• Tighten first nut against the spacer until there is
slight resistance when crank is turned. Do not
overtighten and cause crank to bind. Lock nut in
place using two wrenches and second 5/8" nut.
5/8" NUT
i_ _- .... t_ SPACER, 5/8" x 5/8"
THREADED TUBE /
/\CRANK
STEP 1: (SEE FIGURE 1)
Assemble adjusting brackets to inside of both beams
using one 1/2 x 1-3/4" hex bolt and 1/2" lock nut. Do
not tighten yet.
\
1/2 x 1-3/4" HEX BOLT
\1/2" LOCK NUT
\
ADJUSTING
BRACKETS
FIGURE 1
FIGURE 2
STEP 3: (SEE FIGURE 3)
Measure the distance between the rear wheels of
your tractor and consult the table below for how to
assemble the hitch bracket and which hole to use
with hitch bracket
Assemble hitch bracket between beams using two
5/8 x 2" hex bolts and 5/8" lock nuts.
• Do not tighten yet.
DISTANCE BETWEEN REAR USE HOLE #
TRACTOR WHEELS (iNCHES)
16-19 1R
19-21 2L
21+ 3L
t
5/8 x 2" HEX BOLT _
,/t
_" 5/8" LOCK NUT
6
FIGURE 3
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE

STEP 4: (SEE FIGURE 4)
• Assemble the landside to frog using two 3/8 x 1" plow
bolts and 3/8" hex nuts. Do not tighten yet.
3/8" HEX NUT
/
FIGURE 4
STEP 6: (SEE FIGURE 6)
•insert 1/2 x 1-1/2" carriage bolt through frog and
standard, securing it with a 1/2" hex nut. Do not
tighten yet.
•insert a 1/2 x 1-1/2" hex bolt through tab at bottom of
standard. Place the 1/2" square nut between the tab
and frog, threading the hex bolt into the nut until tight.
• Tighten fasteners assembled in steps 4-6 at this time.
1/2"x 1-112"
0i 1/2" HEX NUT
,/
I
/
i
I
112x 1-112"
HEX BOLT
FIGURE 6
STEP 5: (SEE FIGURE 5)
Attach the standard to the frog using a 1/2 x 2" plow
bolt and 1/2" hex nut. Do not tighten yet.
\
1/2" HEX NUT
j.'
1/2 x 2" PLOW BOLT \\..
FIGURE 5
STEP 7: (SEE FIGURE 7)
*Insert the standard between the beams and fasten
together using the lower hole in the standard with one
1/2 x 1-3/4" hex bolt and 1/2" lock nut.
*Attach end of threaded tube to upper hole on side
of standard using one 1/2 x 1-1/2" hex bolt, 1/2" flat
washer, a 9/16" spacer placed inside hole of standard
and a 1/2" lock nut.
= Tighten fasteners assembled in this step but make
sure threaded tube is free to pivot.
1/2 x1-1/2" HEX BOLT
_. 1/2" FLAT WASHER
/
h_,_ _ 9/18" SPACER
/. (
112 x 1-314"
HEX BOLT
1/2" LOCK
NUT
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
FIGURE 7
7

STEP 8: (SEE FIGURE 8)
insert coulter standard into fork; align the holes and
drive the 5/16 x 1-1/4" pin through. Leave an equal
amount of pin showing on each side.
COU ER ii
STANDARD i/
I
I
I
I
I
FIGURE 8
STEP 10: (SEE FIGURE 10)
*install the coulter blade on the fork by inserting the axle
through one leg of the fork, the coulter hub and the
other leg of the fork. Secure with two 5/8" flat washers
and an 1/8 x 1-1/4" cotter pin by bending the ends over.
i i
i i
COULTER AXLE
s
\,\
•/_ • \ J \\\
118x 1-1/4" COTTER PIN
FIGURE 10
STEP 9: (SEE FIGURE 9)
*Attach the coulter hub to the coulter blade using three
5/16 x 3/4" carriage bolts, 5/16" fiat washers and
5/16" lock nuts.
5/16 x 3/4"
CARRIAGE BOLT
\\\
5116"LOCK.UT
\: ••
\
/'
\\\ /
--- .--_/_ COULTER
5/16" FLAT BLADE
WASHER
FIGURE 9
STEP 11: (SEE FIGURE 11)
*Attach the coulter assembly to the plow beam using
the "U" bolt, coulter clamp, two spacers (located
between the plow beams) and secure with two 5/8"
hex nuts.
*Position the coulter standard between the "U" bolt and
coulter clamp and move up to the highest position.
*Refer to the coulter adjustment section for proper
setting to be adjusted after you begin plowing.
*Tighten bolts assembled in step 3 at this time.
SPACER, 5/8" x 112"
/
5/8" HEX NUTS
\ \
r'y
COULTER CLAMP
"U" BOLT
\
FIGURE 11
8 Call 1-868-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE

PREADJUSTMENT
NOTE: During normal plowing, the right side tractor
wheels will be riding in the previously plowed furrow. A
furrow is the cut area your plow makes when turning the
soil. An initial setting for your plow is required to cut the
first furrow on level ground. The following pre-sets will
result in an approximate 5" to 6" plowing depth.
• Remove stabilizer bolts and nuts from sleeve hitch.
The plow must be free to move side to side on hitch.
Lower your tractor lift handle and lock in lowered
position.
Mount the plow to the sleeve hitch with the hitch pin
furnished with the hitch. Refer to figure 3 and the
accompanying table on page 6 to select the proper
mounting hole.
Adjust lift spring tension on hitch as required, see hitch
manual for instructions.
Adjust the depth crank of plow until point of plow
share is on the ground and the rear of plow landside is
approximately 1" off the ground. (Refer to figure 12.)
NOTE: The plow will appear to be angled to the left. This
will allow the plow to run level when the right hand tractor
wheels are in the plowed furrow.
The plowing depth is set by adjusting the tractor sleeve
hitch turnbuckle until hitch drawstrap has about 1" of
slot exposed between pin and end of slot. Loosen the
hex nut on the hitch turnbuckle to adjust it. Make sure to
retighten it after adjusting.
Adjust the plow coulter to its highest position.
Go and make your first two furrows as shown in figure
13 (X to A and turn B to C). Make sure the tractor lift
handle is lowered and locked into the down position.
Plow in third gear and near full throttle. Raise the plow
to the transport position when turning.
If your plow is not plowing at 4" to 5" deep on your initial
two passes, readjust the plow depth crank by turning
it clockwise to go deeper or counter-clockwise to go
shallower. Make this adjustment one turn at a time until
desired depth is obtained. See figure 16 on page 11.
NOTE: The rest of the furrows will be made with the
tractor tires in the previously cut furrows; therefore, the
pitch (depth) of the plow must be readjusted to a 5" to 6"
plowing depth.
Position your tractor with the inside of the right side
wheels against the side of the previously plowed
furrow.
Start plowing for a short distance and check the
depth of the furrow. Adjust the depth crank clockwise
or counter-clockwise one turn at a time until the 5" to
6" depth is obtained.
After plowing depth is set with plow in furrow, stop the
tractor and measure the distance from the centerline
of the plow coulter axle bolt -- it should be about 2"
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
above the ground. If it is not, raise the plow out of the
ground adjust the coulter up or down to obtain the 2"
height. Be sure to adjust side motion at this time (see
coulter adjustment on page 10, figure 15.)
TRACKING ADJUSTMENT (OPTIONAL)
NOTE: If the plow appears to track to the left while
plowing, an adjustment is available to correct this
condition. (Refer to figure 17.)
The tracking adjustment is made by loosening
both 1/2" hex nuts securing the plow bottom to the
standard and turning the tracking adjustment bolt
clockwise two turns. Retighten hex nuts securely.
Repeat adjustment as necessary until plow pulls
straight at 10° from the adjacent plowed swath.
Hitch Drawstrap
Centerline of Plow
Coulter Axle Bolt Depth
Crank
Landside
1" X
Point of Plow Share
FIGURE 12
X-A
i/\
/
E A
I1
I1
D X
Start F-G
FIGURE 13
9

PLOWING TIPS
• High weeds or grass must be cut down with a rotary
mower before plowing.
Never plow when soil is wet. A rule of thumb is to pick
up a handful of soil and roll it into a ball. If the soil
does not crumble, it is too wet. If the soil is too dry, it
may be difficult for the plow to penetrate properly.
Avoid low areas, old roadways, paths and other
places where soil is overly packed.
Expect to have some difficulty plowing thick sod.
However, by using the proper settings for coulter,
hitch and crank, you should be able to do a good job
under most conditions.
Do not tighten stabilizer bolts, the plow must be
free to sway from side to side. (Refer to your hitch
manual.)
Your 10" plow works best at a depth of 5" - 6".
Lay out your field to be plowed and if possible make it
rectangular in shape.
TRACTION
Four 55 lb. weights are required. Refer to diagram
for positioning them. See your local Sears store or
catalog outlet for purchase of weights.
Tire chains or rear chevron tires (agricultural tires)
are also recommended with the plow. See your local
Sears store or catalog outlet or refer to your tractor
owner's manual for tire size.
When plowing heavy clay soil or sod, it will help
to reduce the width of the plow cut. This can be
accomplished by hitching the plow one or two holes
to the left of the recommended setting (see figure 3.)
NOTE: It is easier to plow a few long furrows than many
short ones. Leave some room at each end of the field for
turning your tractor.
Always lift the plow before turning.
Do not plow too fast. Move steadily along so that the
earth will turn over and not fall back over the furrow.
In most soils, this is done at full throttle in third gear.
NOTE: If plowing speed changes, it may be necessary
to re-adjust the depth crank to maintain desired plowing
depth.
In light soils, plowing may often be done in a higher
gear, but if you travel too fast the furrows will be
uneven and the dirt is apt to be thrown rather than
rolled over.
2 - 55 Pound Wheel Weights
1 - 55 Pound Wheel Weight
and Front Weight Bracket
Set Of Tire Chains
1 - 55 Pound Wheel Weight
FIGURE 14
COULTER ADJUSTMENT (SEE FIGURE 15)
The coulter should be adjusted to slice 2" to 3" deep
when plow is in the ground. Make this adjustment by
loosening the two hex nuts which secure the "U" bolt
and then move the coulter assembly standard up or
down as required.
Rotate the coulter assembly to the left so that the
drive pin located in the standard prevents the coulter
from swinging into the plow beam or bottom, now
tighten the two hex nuts. When properly adjusted, the
coulter will be free to swing outward a limited amount
only to the left of the beam.
NOTE: In extremely hard soil, the coulter may actually
prevent the plow from penetrating the surface. Should this
situation occur, raise or remove the coulter entirely.
Pin\
"U" Bolt
Coulter Standard
View
Col
/
Normal Free Swing Range
Nuts
Plow Beam
/
Viewed from rear of Plow
10
FIGURE 15
Call 1-868-578-8388 for missing parts or assembly help
DO NOT RETURN TO STORE

DEPTH ADJUSTMENT (REFER TO FIGURE 16)
*To turn the plow share into the ground to open the
first furrow, adjust the point downward until the plow
is cutting 4" to 5" deep.
*After a few furrows, or desired depth is reached, turn
the crank counter-clockwise to maintain that depth.
Do not allow landside to ride more than 1/2" off
bottom of furrow as this will cause excessive wear on
bottom of share resulting in poor soil penetration and
loss of landside support.
TURNC'OOKW,SETO
Depth Crank j/ INCREASE PLOW DEPTH
/ /
TURN COUNTER-CLOCKWISE
J TO DECREASE PLOW DEPTH
FIGURE 16
TRACKING ADJUSTMENT (REFER TO FIGURE 17)
NOTE: For most plowing conditions, the landside will be
properly adjusted enabling the plow bottom to react like a
rudder while ground engaged. If the tip of the plow share
is too far left of the beam, the plow will tend to overcut
and leave a ragged furrow wall. This condition can be
readily corrected by making the following adjustment.
Loosen both 1/2" hex buts securing plow bottom to
the standard and then turn the tracking adjusting bolt
clockwise two turns. Retighten hex nuts securely.
Repeat adjustment as necessary until plow pulls
straight behind tractor and is plowing 8" to 10" wide.
/
/
/
ii /
Moldboard J
i i
Standard
Frog
//
//
Ji"ii
1/2" Hex Nuts
Loosen before
land bolt
-....Landside Tracking Adjusting Bolt
FIGURE 17
LiFT ASSIST ADJUSTMENT (ADJUSTABLE SLEEVE HITCHES ONLY)
• Raise the tractor lift handle to transport position in order to adjust the spring to decrease lift effort of the attachment.
Loosen the hex jam nut against the spring bushing.
Turn adjusting bolt clockwise until the washer is flush with hitch bracket. This extends spring and reduces lift effort.
Retighten jam nut.
Operate the hitch with the lift link assembly in the center adjustment hole in the lift arm assembly for most conditions.
If spring adjustment does not result in acceptable lift effort, operate the hitch with the turnbuckle assembly in the lower
adjustment hole in the lift arm assembly.
NOTE: The upper adjustment hole can be used for lighter weight attachments.
The moldboard should be kept in a smooth, polished
condition. Fine sandpaper, steel wool, kerosene,
naptha, etc may be used to restore the finish on a
rusty moldboard.
The coulter blade edge should be relatively sharp. If
sharpening is necessary, use a flat file.
o
o
Every 4 hours lubricate the coulter hub bearing
surface through the grease fitting.
For smooth operation and to prohibit the formation
of rust on the crank, keep a light coating of oil on
threads.
NOTE: When lubricating bearing, it is recommended that
you use multipurpose grease.
Call 1-866-576-8388 for missing parts or assembly help 11
DO NOT RETURN TO STORE

PROBLEM
e
Slow ground entry
CAUSE/CONDITION
Improper crank adjustment
• Badly worn plow share
Ground extremely dry and hard due to
lack of moisture
Hitch downward movement restricted by
mower height adjustment
Plow cutting too wide • Improper tracking adjustment
New or rusted bottom
Plow bottom won't polish
REMEDY
* Refer to depth adjustment and turn crank
clockwise 1 or 2 turns at a time.
Uneven plowing depth
Replace with new share.
Add extra weight to tractor or wait until
soil conditions are suitable.
Extreme variations in soil texture and/or
moisture
Adjust for shortest cut height.
See tracking adjustment
Clean bottom frequently during use until
polish is obtained by; clean bottom with
rag soaked in turpentine, or mineral
spirits. Old brick or pumice may also be
used to polish bottom. Or, rub with a rag
soak in oil and dipped in sand.
See plowing tips. Soil too wet or dry.
Plow rides up in harder, dry soil, runs
shallow
Plow goes too deep
Reduce tractor speed in hard spots.
Check depth adjustment.
Check depth adjust, turn counter-
clockwise.
12 Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE

Call1-866-576-8388formissingpartsorassemblyhelp 13
DONOTRETURNTOSTORE

MODEL NO. 486.24560 10-iNCH MOLDBOARD PLOW
32
23 2t
28 \
18
/4
\
k_ 32
24
31
/
/
/
3\28
30 30
/
/
16
18
41 _©
0
/_39 @_39 _.
\46
45
38
/
32
\
lO
8\14
33
34
5
15 _t i
'i i
30
37
26
\36
27
35
6\
29 _,
\
29
17\
11
19\@
@
%-4
17
19
14 Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE

MODEL NO. 486.24560 10=iNCH MOLDBOARD PLOW
REF. PART NO. QTY DESCRiPTiON REF. PART NO. QTY DESCRiPTiON
1 64839 1 Crank 24 47660 1 Carriage Bolt, 1/2"x 1-1/2"
2 25209 2 Half Beam 25 49065 1 Spacer, 1/2" x 9/16"
3 49058 1 Moldboard, 10" 26 R19212113 2 Flat Washer, 5/8"
4 64840 1 Standard 27 43010 1 Cotter Pin, 1/8" x 1-1/4"
5 25224 1 Coulter Standard 28 43020 2 Hex Bolt, 1/2" x 1-1/2"
6 64841 1 Coulter Hub 29 43080 3 Carriage Bolt, 5/16"x 3/4"
7 49060 1 Coulter Blade 30 HA124589 4 Hex Nut, 5/8"
8 49097 1 Landside, 10" 31 712-0206 2 Hex Nut, 1/2"
9 64838 1 Hitch Bracket 32 43262 3 Lock Nut, 1/2"
10 25217 2 Adjustment Bracket 33 712-0261 2 Lock Nut, 5/8"
11 64842 1 Coulter Fork 34 47947 2 Hex Bolt, 5/8" x 2"
12 49056 1 Threaded Tube 35 49067 1 Coulter Axle
13 49063 1 Plow Bolt, 1/2" x 2" 36 49068 1 "U" Bolt
14 49062 5 Plow Bolt, 3/8" x 1" 37 25218 1 Coulter Clamp
15 41155 2 Spacer, 5/8" x 1/2" 38 25225 1 Trunnion
16 41156 1 Spacer, 5/8" x 5/8" 39 R73220700 2 Hex Nut, 7/16"
17 43081 3 Washer, 5/16" 40 43070 3 Flat Washer, 3/8"
18 R74780828 2 Hex Bolt, 1/2" x 1-3/4" 41 41154 2 Plow Bolt, 7/16" x 1-1/4"
19 25H-17 3 Lock Nut, 5/16" 42 43352 2 Washer, 7/16"
20 43015 5 Hex Nut, 3/8" 43 46858 1 Grease Fitting, 5/16"
21 715-0118 1 Roll Pin, 5/16" x 1-3/4" 44 49057 1 Frog
22 49064 1 Square Nut, 1/2" 45 49059 1 Share, 10"
23 HA120396 1 Washer, .5312 x 1.0625 x .09" 49070 1 Owner's Manual
Call 1-888-578-8388 for missing parts or assembly help 15
DO NOT RETURN TO STORE

Your Home
For expert troubleshooting and home solutions advice:
www.managemyhome.com
For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME ®(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)
www.sears.com www.sears.ca
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR ®
1-800-361-6665 (Canada)
Au Canada pour service en fran(_ais:
1-800-LE-FOYER M°
(1-800-533-6937)
TM SM
® Registered Trademark /Trademark /Service Mark of Sears Brands, LLC
TM
® Marca Registrada /Marca de F&brica /SMMarca de Servicio de Sears Brands, LLC
MCMarque de commerce /MDMarque depos6e de Sears Brands, LLC © Sears Brands, LLC