Craftsman TRACTOR LIFT 610.246 User manual

User Instructions
TRACTOR LIFT
Model Number 610.24600
Provides access to mower deck for easy •
cleaning and service
Fits all 1985 through current models •
of CRAFTSMAN front engine tractors
and Zero Turn Mowers
Can be fitted to most major front engine tractor brands •
Adjustable arms for greater versatility •
Extra heavy duty gauge steel construction •
If you read and follow these instructions, this product can be •
assembled in approximately 20 minutes
Assemble unit on cardboard to avoid scratches or damage to parts •
Can easily be assembled by one person •
All fasteners for this Tractor Lift can be purchased at Sears or any •
hardware store
If there are any missing •
parts, or if you have any
questions on assembly,
operation, maintenance
or safety, please call
1-800-652-6231
610.24600-REV B 3/08
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website: www.sears.com/craftsman
Patent Pending

WARNINGS
Always use the stabilizer bar provided when using tractor lift. •
Make sure stabilizer bar is properly in place before starting any
work on tractor.
Read and understand all safety and operating instructions •
before using the tractor lift. Never allow anyone unfamiliar
with these instructions to use the tractor lift.
Read and understand all safety and operating instructions •
provided by the tractor's manufacturer before using tractor lift.
Never lay under the tractor or mowing deck. •
When using lift, keep all bystanders, including children, away. •
This tractor lift must be only used for lifting and lowering to •
and from a level and stable surface.
Never use in wet conditions. •
Do not attempt to lift the front and back of the tractor at the same •
time.
Do not use tractor lift as an automotive lift, or for any other use for •
which it is not intended or designed.
If tractor lift is bowing while lifting or lowering your tractor, which •
indicates an overload condition, remove the tractor immediately.
Do not attempt to lift or lower any power equipment while motor is •
running.
Never engage blades while using tractor lift. •
Always disconnect spark plug wire from tractor before beginning •
any work on tractor.
Do not exceed the rated capacity of the tractor lift - 270#. •
Failure to follow these warnings may result in property •
damage and/or serious bodily injury.
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.
Page 2.
SAFETY INSTRUCTIONS
Be sure to read and follow all safety instructions and •
warnings. Failure to follow these instructions may result in
damage to the product and/or serious personal injury.
Danger of serious personal injury exists. Serious personal •
injury can occur when using a lifting device.
Never attempt to ride any vehicle up or down the tractor lift. •
Do not climb onto tractor while tractor is in the elevated position. •
When working on the front of the tractor always place wheel •
chocks in back of the rear wheels/tires.
Always raise and lower tractor lift in a controlled fashion; do not •
allow the tractor to drop too quickly, damage could occur.
Make sure lifting arms are aligned and set to the proper distance apart •
so that the equipment being loaded is well balanced on the lift.
Do not remove warning decals from product. •
Before each use, always check for any worn, loose, or •
damaged parts on the tractor lift. If any damage is present,
DO NOT USE THE TRACTOR LIFT .
Periodically check the fasteners to make sure they are still •
tight and in place.
Keep lift surface clean by occasionally cleaning with water and •
any mild detergent.
Do not add to or try to modify the tractor lift in any way. •
Any modifications will void any warranties.
Failure to abide by the warnings and read the safety instructions may •
result in loss of load, damage to lift and/or property, serious personal
and/or fatal injury.

2
3
1
6
4
7R 7L
8
11
10
Tractor Lift can be used out of the box on all Craftsman tractors
with bumpers or brush guards. Tractor Lift mounting hardware is
provided if your tractor does not have a bumper or brush guard.
OPERATION MAINTENANCE
Store unit in a clean dry place.
Recommended tire pressure - 30 PSI.
Before each use:
Always check tire pressure. •
Always inspect unit for damage. •
Always check fasteners for tightness. •
TOOLS REQUIRED FOR ASSEMBLY
9/16" Wrench and/or Socket
Adjustable wrench
REF NO QTY PART NUMBER DESCRIPTION REF NO QTY PART NUMBER DESCRIPTION
1 1 51001 Angle Frame Assembly 7L 1 410131 Tractor Mounting Bar - Left
2 1 51002 Handle Top 7R 1 410132
Tractor Mounting Bar - Right
3 1 51003 Handle Bottom 8 1 51006 Stabilizer Bar
4 2 41009 Lift Tube Assembly 10 1 310031 Hardware Bag
6 1 51005 Lift Cross Tube 11 1 310041 Assembly Manual
Carton Contents
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.
Page 3.

37
26 22
38
23
24 28
29
35
25
27
33
34
36
39
Hardware Contents
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.
Page 4.

10.00000000
2.00000000
I
26
6
26 38
10.00000000
2.00000000
I
DETAIL I
SCALE 1 : 5.5
7R
29
27
24
"X"
7L
Remove,
add washer ( 24 ),
replace.
Step 1. Step 2.
Tractor Lift can be used out of the box on all Craftsman tractors with bumpers or brush guards. Tractor Lift mounting hardware is provided. If
your tractor does not have a bumper or brush guard, follow the steps below:
Note: Left and Right sides are determined by standing behind tractor looking forward.
Step 1.
Remove existing bolt "X" and set aside. If tractor does not have •
this bolt use supplied 3/8" x 1-1/4" bolt with 3/8 nylok nut.
Align holes in tractor mounting bars ( 7R & 7L ) to the front •
left & right side frame holes of the tractor.
Insert hex head bolt ( 29 ) through inside front hole of frame, •
through tractor mounting bar and secure with nylock nut ( 27 ).
Add flat washer ( 24 ) under head of bolt removed in earlier •
step and reinsert through tractor mounting bar and tighten.
For LT1000 & LT2000 series tractors, use self-thread bolts •
( 28 ) in place of bolt ( 29 ) and nut ( 27 ).
Step 2.
Push tube plugs ( 38 ) into each end of lift tube ( 6 ). •
Slide lift tube through cut-out in tractor mounting bars and •
center.
Pin lift tube in place with one hair pin cotter ( 26 ) on each side •
of mounting bar.
Note: The mounting bars have been manufactured to attach to the
frames of most major front engine tractor brands. Additional
hardware has been included for attachment to non-Craftsman
brands.
Setting up Lift Mounting Hardware - Tractor Front
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.
Page 5.

4
22
24
23
25
1
23
25
24
29
Note: The higher the lift tube extensions (5)
are positioned, the harder the tractor will be to lift.
5
A B C DD
C B A
Push mower
Brush guard bumper
(can also be used for
front of Craftsman tractor)
Front of Craftsman Zero Turn
Front of Craftsman Tractors
Settings:
A. Push Mower
B. Brush guard / Bumper installed
C. Front of Craftsman Tractor
D. Front of Craftsman Zero Turn
Lift tubes come pre-assembled. Attach lift tube assemblies ( 4 ) to angle frame ( 1 ) using bolts ( 22 ), flat washers ( 24 ), split lock washers ( 23 ) •
and hex nuts ( 25 ).
Secure rear of lift tube assembly ( 4 ) to angle frame ( 1 ) using bolts ( 29 ), flat washers ( 24 ), split lock washers ( 23 ) and hex •
nuts ( 25 ).
Note: Over-tightening receiver bolts ( 22 ) could cause damage to lift tubes ( 4 ).
Determining the width between lift tubes.
Assemble Tractor Lift
Attach Lift Tubes to Angle Frame
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.
Page 6.

3
22
24
23
30
224
23
25
25 1
33
30
38
38
37
37
Foot Bar Tube
Handle Top Tube
30 39
Peel off scuff pad (39)
backing and adhere to
back of handle.
IF HANDLE CANNOT BE
EASILY INSERTED, FLIP
HANDLE OVER AND
REINSERT.
Step 1. Attach handle bottom ( 3 ) to angle frame ( 1 ) using hex bolt ( 22 ),
flat washer ( 24 ), split lock washer ( 23 ) and hex nut (25 ).
Step 2. Insert ring grip pin ( 30 ), as shown.
Step 3. Insert handle top ( 2 ) into handle bottom ( 3 ). Secure with hex
bolt ( 33 ), flat washer ( 24 ), split lock washer ( 23 ) and hex nut (25 ).
Step 4. Place handle grips ( 37 ) onto handle top tube ( 2 ). A little
soapy water will help grip slide onto tube easily.
Assemble Tractor Lift
Attach Handle to Angle Frame
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.
Page 7.

Snap button
Foot bar tube
8
Step 1. Slide stabilizer bar ( 8 ) onto foot bar tube as shown.
Step 2. Press snap button and slide stabilizer bar against handle.
Step 3. Insert ring grip pin ( 30 ) through stabilizer bar and handle top.
30
Assemble Tractor Lift
Attach Stabilizer Bar
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.
Page 8.

30 8
Tube Handle
Snap Button
Turn 180
Figure 1 Figure 2
Snap Button
Step 3. Engaging Stabilizer Bar
Stabilizer bar MUST be engaged immediately after raising the tractor.
WARNING : Failure to engage stabilizer bar may result in serious personal
injury and or property damage.
Remove ring grip pin ( 30 ) from tube handle. Press snap button •
and slide stabilizer bar ( 8 ) from foot bar tube.
Turn stabilizer bar 180 degrees as shown at bottom of Figure 1. •
Position stabilizer bar under base of unit between wheels. •
Slide stabilizer bar back onto foot bar tube making sure the bar is •
positioned back over snap button.
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m. E.S.T.
Page 10.
OPERATION
Using the Tractor Lift