Craftsman 610.24610 User manual

User Instructions
ICR FTSM
TRACTOR LIFT
Model Number 610.24610
®
Provides access to mower deck for easy
cleaning and service
Fits all 1985 through current models
of CRAFTSMAN front engine tractors
and zero turn mowers
• Adjustable arms for greater versatility
Patent Pending
• Extra heavy duty steel construction
If you read and follow these instructions, this product can be
assembled in approximately 20 minutes
• Assemble unit on cardboard to avoid scratches or damage to parts
Can easily be assembled by one person
All fasteners for this Tractor Lift can be purchased at Sears or any
hardware store
If there are any missing
parts, or if you have any
questions on assembly,
operation, maintenance
or safety, please call
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website: www.sears.com/craftsman
1-800-652-2321
Made inChina 310041-REV C 1/09

WARNINGS
• Always check to ensure stabilizers are properly in place and
stabilizer latches are engaged before starting any work on tractor.
• Read and understand all safety and operating instructions
before using the tractor lift. Never allow anyone unfamiliar
with these instructions to use the tractor lift.
• Read and understand all safety and operating instructions
provided by the tractor's manufacturer before using tractor lift.
• Never lay under the tractor or mowing deck.
• When using lift, keep all bystanders, including children, away.
• This tractor lift must be only used for lifting and lowering to
and from a level and stable surface.
• Never use in wet conditions.
• Do not attempt to lift the front and back of the tractor at the same
time.
• Do not use tractor lift as an automotive lift, or for any other use for
which it is not intended or designed.
• If tractor lift is bowing while lifting or lowering your tractor, which
indicates an overload condition, remove the tractor immediately.
• Do not attempt to lift or lower any power equipment while motor is
running.
• Never engage blades while using tractor lift.
• Always disconnect spark plug wire from tractor before beginning
any work on tractor.
• Do not exceed the rated capacity of the tractor lift - 275 Ibs.
• Failure to follow these warnings may result in property
damage and/or serious bodily injury.
SAFETY INSTRUCTIONS
Be sure to read and follow all safety instructions and
warnings. Failure to follow these instructions may result in
damage to the product and/or serious personal injury.
Danger of serious personal injury exists. Serious personal
injury can occur when using a lifting device.
Never attempt to ride any vehicle up or down the tractor lift.
Do not climb onto tractor while tractor is in the elevated position.
When working on the front of the tractor always place wheel
chocks in back of the rear wheels/tires.
Always raise and lower tractor lift in a controlled fashion; do not
allow the tractor to drop too quickly, damage could occur.
Make sure lifting arms are aligned and set to the proper distance apart
so that the equipment being loaded is well balanced on the lift.
Do not remove warning decals from product.
Before each use, always check for any worn, loose, or
damaged parts on the tractor lift. If any damage is present,
DO NOT USE THE TRACTOR LIFT.
Periodically check the fasteners to make sure they are still
tight and in place.
Keep lift surface clean by occasionally cleaning with water and
any mild detergent.
Do not add to or try to modify the tractor lift in any way.
Any modifications will void any warranties.
Failure to abide by the warnings and read the safety instructions may
result in loss of load, damage to lift and/or property, serious personal
and/or fatal injury.
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m.E.S.T.
Page 2.

Carton Contents .........................................................................
10
REF NO
1
2
3
4
QTY
1
1
1
2
PART NUMBER
510016
510023
510034
51008
DESCRIPTION
Frame Assembly
Handle, Top
Handle, Bottom 10
Lift Tube Assembly 11
REF NO
6QTY 1
2
1
1
PART NUMBER
510052
410133
310037
310041
DESCRIPTION
Bar, Lifting
Bracket, Tractor
Hardware Bag
Assembly Manual
OPERATION
Tractor Lift can be used out of the box on all Craftsman tractors
with bumpers or brush guards. Tractor Lift mounting hardware is
provided if your tractor does not have a bumper or brush guard.
TOOLS REQUIRED FOR ASSEMBLY
9/16" Wrench and/or Socket
Adjustable wrench
MAINTENANCE
Store unit in a clean dry place.
Recommended tire pressure - 30 PSI.
Before each use:
• Always check tire pressure.
• Always inspect unit for damage.
• Always check fasteners for tightness.
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m.E.S.T.
Page 3.

Hardware Contents
¢.....--
L..._
29
t'--
L___
22
24 23 25
28
(O )
27 31 32 26
REF NO
23
24
25
26
QT'r"
3
5
4
PARTNUMBER
310051
310072
310073
310062
300082
310061
DESCRIPTION
318"-1 6 x 2-3/4" Hex Bolt
3/8" Split Lock Washer
3/8" USS Flat Washer
3/8"-1 6 He;,( Nut
Hairpin Cotter
3/8"-1 6 ['¢;/Ioc Hex Nut
REF NO QTY PARTNUMBER
28 310054
29 8 310055
31 1 310063
32 1 310074
318"-16 x 1-1/2" Self-th read Bolt
318"-16 x 1-114" Hex Bolt
1t2"-13 Hex Nut
112" USS Flat Washer
FOR MISSING PARTS, Ca111-800-652-2321, Monday-Friday, 8 a.m.-5 p.m.E.S.T.
Page 4.

Setting up Lift Mounting Hardware
Tractor Lift can be used out of the box on all Craftsman tractors with bumpers or brush guards. For tractors without bumper or brush guard,
Tractor Lift mounting hardware is provided. Follow the steps below:
Front
6
IlXll
Remove,
add washer ( 24 ),
replace. Rear
31
32
6
Remove existing bolt "X" and set aside. If tractor does not
have this bolt, use supplied 3/8" x 1-1/4" bolt and 3/8" nyloc nut.
Insert bolt ( 29 ) through inside front hole of frame, through
tractor bracket ( 7 ) and secure with nyloc nut ( 27 ).
Add flat washer ( 24 ) under head of bolt removed in earlier
step and reinsert through tractor mounting bar and tighten.
For LT1000 & LT2000 series tractors, use self-thread bolts
( 28 ) in place of bolt ( 29 ) and nut ( 27 ).
Slide lifting bar ( 6 ) through cut-out in tractor brackets.
Pin lifting bar in place with one hairpin cotter ( 26 ) on each
side, inside of tractor brackets ( 7 ).
Place lifting bar ( 6 ) under rear tractor hitch and slide threaded
stud through hole.
Secure in place with flat washer ( 32 ) and hex nut ( 31 ).
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m.E.S.T.
Page 5.

Assemble Tractor Lift
Attach Lift Tubes to Angle Frame
Lift tubes come pre-assembled. Attach lift tube assemblies ( 4 ) to angle frame ( 1 ) using bolts ( 22 ), flat washers ( 24 ), split lock
washers ( 23 ) and hex nuts ( 25 ).
Secure rear of lift tube assembly ( 4 ) to angle frame ( 1 ) using bolts ( 29 ), flat washers ( 24 ), split lock washers ( 23 ) and hex
nuts ( 25 ).
Note: Over-tightening receiver bolts ( 22 ) could cause damage to lift tubes ( 4 ).
Determining the width between lift tubes.
Craftsman Tractor Brush guard /Bumper
Front of Craftsman Zero Mower
4
5
Note: The higher the lift tube extensions (5)
are positioned, the harder the tractor will be to lift.
Settings:
A. Push Mower
B. Brush guard /Bumper
C. Craftsman Tractor
D. Front of Craftsman Zero Turn
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m.E.S.T.
Page 6.

Assemble Tractor Lift
Attach Handle to Angle Frame
Step 1. Attach handle bottom ( 3 ) to angle frame ( 1 ) using hex bolt ( 22 ),
flat washer ( 24 ), split lock washer ( 23 ) and hex nut (25).
Step 2. Insert ring grip pin ( 30 ), as shown.
Step 3. Insert handle top ( 2 ) into handle bottom ( 3 ). Secure with hex
bolts ( 29 ) and split lock washer ( 23 ).
24
2
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m.E.S.T.
Page 7.

Using the Tractor Lift
Center Tractor Lift in front of tractor.
Check that both stabilizers are resting on the ground as shown.
Align lift tube claws with lifting bar or bumper/brush guard and
roll Tractor Lift forward to engage.
Check that claws are securely hooked under the lifting bar or
bumper/brush guard.
Place foot onto foot bar and apply continuous forward pressure
with foot while pulling down on tractor lift handle.
Once lifted, the weight of the tractor will automatically force the
handle down into the correct position.
Always check that stabilizer latches are in the locked position
after lifting tractor.
Stabilizer latches must be flipped to the unlocked position
before lowering tractor.
Locked Unlocked
FOR MISSING PARTS, Ca111-800-652-2321, Monday-Friday, 8 a.m.-5 p.m.E.S.T.
Page 8.

Repair Parts List 7
MODEL NUMBER - 610.246101_" _ - '_:I'_
!26
29
25
11
REF. NO.
1
3
4
5
6
7
8R
8L
9
10
11
20
21
22
PART NO. AMT. DESCRIPTION
510012 1 Fra me
510022 1 Handle, Top
510032 1 Handle, Bottom
51004 Lift Tube
51007 Receiver Tube
510052 1 Bar, Lifting
410133 Bracket, Tractor
510061 1 Stabilizer, Right
510062 1 Stabilizer, Left
310011 2 Wheel, 10" x 518"
310037 1 Hardware Bag
310041 1 Assembly Manual
310071 2 Washer, 5t8" SAE
300081 2 Cotter Pin 1t8" x 1-112"
310051 3 3/8"-16 x 2-314" Hex Bolt G R5
REF. NO.
23
24
25
26
28
29
30
31
32
37
38
39
40
41
PART NO. AMT.
310072 7
310073 7
310062 5
300082
310061 4
310054 2
310055 8
310081 3
310063 1
310074 1
310181 2
310221 2
31026 1
310341 2
31041 2
***Not Shown, see hardware bag contents.
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m.
Page 9.
DESCR I PTI ON
3/8" Split Lock Washer
3/8" USS Flat Washer
318"-16 Hex Nut
Hairpin Cotter .148 Wire, 3-5/16"
318"-16 Nylok Hex Nut
**'3t8"-16 x 1-1t2" Self-thread Bolt
**'318"-16 x t-114" Hex Bolt GR5
Pin, Quick-Release
112"-13 Hex Nut
1/2" USS Flat Washer
Grip, Handle
Plug, 1" Tube
Pad, Scuff
Retaining Ring, 5/8"
Latch, Safety
E.S.T.
10

CRAFTSMAN THREE YEAR LIMITED WARRANTY
If this Craftsman product fails due to a manufacturer's defect within three years from the date of purchase, return it to
any Sears store or other Craftsman outlet in the United States for free replacement.
This warranty does not provide product replacement due to wearing off or fading of product paint, or wearing out or
failure of product tires or wheels.
This warranty is void if this product is ever used for commercial or rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179.
PRODUCT RECORD
In the space below record the model number and
purchase date of your cart. The model number can
be found on the front cover of the user guide.
Model Number
Purchase Date
Keep this booklet and your Sears receipt in a safe
place for future reference.
ORDERING INFORMATION
After the three year warranty period all parts may
be ordered by calling Sears Service at
1-800-4MY-HOME (1-800-469-4663).
When ordering repair parts, always give the
following information:
Product -
Model Number-
Part Number - *
Part Description - *
*Found on the repair part list. Reference page 9.
NOTES