Craftsman 486.24247 User manual

Operator's Manual
®
15 CU. FT. POLY CART
Model No. 486.24247
DO NOT RETURN TO STORE
For Missing Parts or Assembly
Questions Call 1-866-576-8388
CAUTION:
Before using this product, read
this manual and follow all Safety
Rules and Operating instructions.
,, Safety
,, Assembly
,, Operation
,, Maintenance
,, Parts
Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.
www.sears.com/craftsman
PRINTED IN U.S.A. FORM NO. 41761 (12/12/14)

WARRANTY & SAFETY .................................................. 2
FULL SIZE HARDWARE CHART .................................... 3
CARTON CONTENTS ..................................................... 4
ASSEMBLY ...................................................................... 4
OPERATION .................................................................... 8
MAINTENANCE .............................................................. 8
SLOPE GUIDE ................................................................ 9
REPAIR PARTS ILLUSTRATION .................................. 10
REPAIR PARTS LIST ..................................................... 11
PARTS ORDERING/SERVICE ...................... BACK PAGE
CRAFTSMAN LIMITED WARRANTY
FOR TWO YEARS from the date of sale this product is warranted against defects in material or workmanship.
WITH PROOF OF SALE a defective product will be replaced free of charge.
For warranty coverage details to obtain free replacement, visit the web page: www. craftsman, com/warranty
This warranty does not cover expendable items that can wear out from normal use or deterioration within the warranty
period, including but not limited to tires, belts, exterior finishes or product labels.
This warranty does not apply to a product that is damaged or altered through transportation, misuse, abuse, corrosion,
accident, neglect, modification or mishandling.
This warranty is void if this product is ever used while providing commercial services or if rented to another person.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
DO NOT RETURN TO STORE for Missing Parts or Assembly Questions
Call 1-866-576-8388 Attachment Hotline
The model number and serial numbers will be found on a
decal attached to the 15 Cu. Ft. Poly Cart.
You should record both the serial number and the date of
purchase and keep in a safe place for future reference.
MODEL NUMBER:
SERIAL NUMBER:
DATE OF PURCHASE:
486.24247
Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to
operate the equipment. Exercise caution at all times when using power equipment.
LOOK FOR THIS SYMBOLTO POINT OUT
iMPORTANT SAFETY PRECAUTIONS. IT
MEANS - ATTENTION! BECOME ALERT!
YOUR SAFETY IS iNVOLVED.
CAUTION: VEHICLE BRAKING AND
STABILITY MAY BE AFFECTED WITH THE
ADDITION OF AN ACCESSORY OR AN
ATTACHMENT. BE AWARE OF CHANGING
CONDITIONS ON SLOPES.
Exercise caution at all times when using power equipment.
1. Read this owners manual before attempting to assemble or operate the cart.
2. Read the vehicle owners manual and know how to operate your tractor, before using the cart attachment.
3. Do not at any time carry passengers in this cart. It has not been designed to carry passengers.
4. Never allow children to operate the tractor or the cart attachment.
5. Do not allow adults to operate the tractor or cart attachment without proper instructions.
6. Always begin with the transmission in first (low) and gradually increase speed as conditions permit.
7. Tow the cart at reduced speed over rough terrain and hillsides or near creeks and ditches to prevent tipping over and
loss of control. Do not drive too close to a creek or ditch.
8. Vehicle braking and stability may be affected with the attachment of this cart. Do not fill cart to maximum weight
capacity without checking the capability of the towing vehicle to safely pull and stop with the cart attached.
9. Before operating vehicle on any grade (hill) refer to the safety rules in the vehicle owner's manual concerning safe
operation on slopes. Refer also to the slope guide on page 11of this manual. Stay off steep slopes!
10. Do not tow this cart on highways or on public thoroughfares.
11. Maximum towing speed is 10 m.p.h.
12. Follow maintenance and lubrication instructions as outlined in this manual.
2

REF QTY. DESCRiPTiON REF QTY. DESCRiPTiON
A 1 Hex Bolt, 5/16" x 4" J 4 Flat Washer, 1/4"
B 1 Hex Bolt, 3/8" x 1" K 4 Flat Washer, 1"
C 4 Hex Bolt, 1/4" x 3/4" L 2 Cotter Pin, 1/8" x 1-1/2"
D 8 Truss Head Bolt, 5/16" x 3/4" M 1 Extension Spring
E 4 Nylock Nut, 1/4" N 1 Hitch Pin
F 9 Nylock Nut, 5/16" 0 1 Hair Cotter Pin, 1/8"
G 2 SEMS Nut, 5/16" P 1 Spring Puller Tool
H 1 Nylock Nut, 3/8" Q 2 Thick Washer
I 2 Hub Cap
SHOWN FULL SIZE
NOT SHOWN FULL SIZE

1. Poly Tray 4. Latch Stand Bracket 7. Latch Lock Lever
2. Wheel Support 5. Draw Bar Tongue 8. Hitch Bracket
3. Latch Stand Plate 6. Wheels (2) 9. Axle
TOOLS REQUIRED FOR ASSEMBLY
(1) Phillips Screwdriver
(1) Pliers
(2) 7/16" Wrenches
(2) 1/2" Wrench
(2) 9/16" Wrenches
STEP 1: (SEE FIGURE 1)
•Verify that all parts and all fasteners on pages 2 and
3 are included in the carton and parts bag. Refer
to page 2 to identify fasteners used in the following
instructions.
Place the latch lock lever (7) through the slot in the
tongue (5). Assemble the hex bolt (A) through the
tongue, the lever, and two (SEMS) hex nuts (G)
placed on each side of the lever. Assemble the nylock
nut (F) onto the end of the hex bolt (A) and tighten
so that the hex bolt (A) can still rotate freely. Tighten
the two (SEMS) hex nuts (G) against each side of the
latch lock lever (7) so that it is centered in the slot. FIGURE 1

STEP 2: (SEE FIGURE 2)
= Hook the short end of the spring (M) intothe hole in
the latch lock lever. Use the spring puller tool (P) to
hook the long end of the spring into the square hole
in the tongue. The spring puller tool can be stored
when finished.
STEP 4: (SEE FIGURE 4)
Lay the tongue (open side facing up) onto the wheel
support (2). Assemble the axle (9) through the wheel
support and the tongue.
FIGURE 4
FIGURE 2
STEP 3: (SEE FIGURE 3)
= Assemble the end of the hitch bracket (8) down
through the slot at the front of the tongue. Fasten it
to the tongue using the hex bolt (B) and hex nut (H).
Tighten.
Assemble the hitch pin (N) and hair cotter pin (O) to
the tongue and hitch bracket.
STEP 5: (SEE FIGURE 5)
• Assemble a washer (K), a thick washer (Q) a wheel
(6) with the valve stem facing out, and another
washer (K) onto the axle. Assemble a cotter pin (L)
to the axle. Press a hub cab (I) onto the washer (K).
Repeat on other end.
FIGURE 5
FIGURE 3

STEP 6: (SEE FIGURE 0)
= Assemble the latch stand plate (3) and the latch
stand bracket (4) at the front of the tray using four hex
bolts (C), washers (J) and hex nuts (E). The aligning
tab on the bottom of the latch stand bracket must be
towards the rear of the cart. Tighten.
FIGURE 6
STEP 7: (SEE FIGURE 7)
= Place the tray onto the wheel support and position it
so that the latch stand bracket locks into the latch lock
lever. Fasten the tray to the wheel support using eight
truss head bolts (D) and hex nuts (F). Tighten.
FIGURE 7

CAUTION:VEHICLEBRAKINGAND
STABILITY MAY BE AFFECTED WITH
THE ADDITION OF AN ACCESSORY
OR AN ATTACHMENT. BE AWARE OF
CHANGING CONDITIONS ON SLOPES.
,
,
,
Refer to the vehicle owners manual for instructions on
safe operation on slopes.
Use the slope guide provided on page 11 of this
manual to determine whether slope angle is too steep
for safe operation.
For best handling and traction, distribute the weight of
the load evenly in the cart.
Always test to make sure your tractor has adequate
towing and braking capabilities whenever hauling a
substantial amount of weight in your cart. Use extra
caution when operating on slopes.
NOTE
DO NOT EXCEED WEIGHT CAPACITY OF CART
(See the specifications on this page.)
One cubic foot of dirt weighs approximately 80 Ibs.
,
,
4.
At the beginning of each season, using a light
machine oil, lubricate the latch, the latch pivot bolt,
and the area of the axle where the draw bar tongue
pivots.
Grease or oil the wheel bearings periodically. Use
automotive wheel bearing type grease or 20 weight
oil.
Check periodically for loose bolts.
Keep tires filled to the recommended tire pressure of
12-14 Lbs.
CART SPECIFICATIONS
Tires: 15" x 6" Pneumatic
Axle: 1" Dia. Steel
Capacity: Up to 750 Lbs. Max.
Approx. Sh.Wt. 105 Lbs.
,To dump material from the cart, release the spring
latch on the tongue by pulling the latch lock lever
forward, away from the cart. The cart bed will then tilt
backwards to empty its contents. After emptying, pull
the front of the bed down toward the cart tongue until
the latch snaps into place.
6. The maximum towing speed for this cart is 10 m.p.h.
CAUTION: TO AVOID POSSIBLE
iNJURY, BEFORE RELEASING THE
LATCH BE SURE THAT NO ONE IS
NEAR THE CART.

C
1=..
|_
m
:3-
|_
CL_
j;
.m
v
I=..
"o
C
I=..
o
1=..
:3
o
o
C
o
I=..
:3
o_I=..
C
(n o
o,.c
_=
o ::3
_N
|
|
|
|
|
|
|
H
|
I
|
|
|
H
|
|
|
|
|
|:
H
|
|
|l
|,
SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE
APOWER POLE
-A CORNER OF A BUILDING
|
|
CAUTION: DO NOT OPERATE YOUR TRACTOR AND CART ON A
SLOPE iN EXCESS OF 10 DEGREES. BE SURE OFYOURTRAC-
TOR'S TOWING AND BRAKING CAPABiLiTiES BEFORE OPERATING
ON A SLOPE. AVOID ANY SUDDEN TURNS OR MANEUVERS WHILE
ON A SLOPE.
Ob

10

REF. PARTNO. QTY. DESCRiPTiON
1 48608 1 PolyTray
2 25106 1 WheelSupport
3 24386 1 LatchStandPlate
4 24497 1 LatchStandBracket
5 24750 1 Tongue,DrawBar
6 46272 2 WheelAssembly
7 24498 1 LatchLockLever
8 23014 1 HitchBracket
9 . 24897 J 1 .Axle. l"
10 43088 4 Flat Washer, 1/4"
11 47407 1 Hex Bolt, 5/16" x 4"
12 47622 1 Spring Puller Tool
13 44488 4 Wheel Bearing, 1"
14 43093 2 Cotter Pin, 1/8" Dia. x 1-1/2" *
15 43601 4 Washer, 1"
16 47810 9 Hex Nut, 5/16-18 Nylock *
17 43001 1 Hex Bolt, 3/8-16 x 1" *
18 43814 8
19 47189 4
20 43012 4
21 47408 1
22 23353 1
23 43343 1
24 46980 2
25 43014 2
26 HA21362 1
27 25483 2
48611 1
Truss Head Bolt, 5/16-18 x 3/4"
Hex Nut, Nylock 1/4-20
Hex Bolt, 1/4-20 x 3/4" *
Extension Spring
Hitch Pin
Hair Cotter Pin, 1/8" *
Hex Nut, 5/16-18 (SEMS)
Hub Cap
Hex Nut, 3/8-16 Nylock *
Washer, 1.03 x 1.75 x 0.25"
Owner's Manual
* Purchase Common Hardware Locally
11

1-888 31 569
ustom Hot
piezas o pedir servicio para la reparaci6n de su equipo.
To help us help you, register your product at www.craftsman.com/registration
Para poderte ayudar mejor, registra tu producto en www.craftsman.com/registration
Join the Craftsman Club today!
@
www.craftsman.com/signup
Receive exclusive member benefits including special pricing and offers,
project sharing, expert advice, and SHOP YOUR WAY REWARDS!
Como miembro exclusivo, recibe diversos beneficios como ofertas, precios especiales, proyectos
nuevos, consejos de expertos y nuestro programa de puntos SHOP YOUR WAY REWARDS!
® Registered Trademark /TMTrademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries
® Marca Registrada /TMMarca de Fabrica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC in otros paises