Creative Solutions Postal Pro PP200 User manual

Sept. 5, 2019
Postal Pro PP200 Post Kit - Instructions
Parts List
A. Vertical Post: 4x4 Square PVC Post –50.75-inch length E. Mailbox Mounting Kit
B. Cross Arm: 3.5” x 3.5” PVC –26-inch length - (4) 10-24 x 1 ¼ length threaded screw - (4) 10-24 Nuts
C. Top Finial Fits on top of Vertical Post - (4) #8 Self Drill Screw –1-inch Length - (2) Metal U-Brackets
D. End Caps (2) Fits on end of cross arm - (6) #12 White Self Drill Screw –1 inch - (6) Post Cap Clips
Install Ground Mounting Post –Not Included
• The PP200 Post is designed to slip over a Mounting Post made from a standard 4x4 wooden post (actual dimensions are 3.5 x 3.5.) Two 2x4 boards can be
combined to provide an alternative Mounting Post.
• Mounting Post should be set 18 inches in to the ground and between 18-24 inches above ground.
Assemble PP200 Post
1)
Slide Cross Arm in to the opening in the Vertical Post. (See Figure 1)
2)
Leave 17" of the Cross Arm extending in front (mailbox side) of the Vertical Post.
3)
Secure the Cross Arm into place using (2) #12 x 1 Self Drilling Screws where it intersects with Vertical Post. (1 screw on each side) (See Figure 2)
4)
(6) Post Cap clips have been included in the hardware kit for installation of End Caps and Top Finial to the Post and Cross Arm. Attach Clips as shown (See
Figures 3 and 4) below with barb side on outside of PVC posts. Use (2) Clips per post end application. NOTE: Clips are to be centered between corners as shown in
pictures. After clips are in place, slip on End Caps and Finial caps for secure installation.
5)
You can now slip Assembly over Ground Mounting Post. Use (4) of #12 x 1 Self Drilling Screws with white heads to secure PP200 Assembly to Mounting Post.
Figure 1 Figure 2 Figure 3 Figure 4
Postal Regulations recommend that the floor (mail entry point) of the mounted Mailbox be between 41”-45” above the road surface and that the front of the
mailbox be set back 6-8” from the edge of road or front of curb. The USPS suggests that all customers contact their local Post Office before installing your
Mailbox/Post to ensure correct placement and height at the street.

Sept. 5, 2019
Mailbox Mounting Brackets and Mailbox
1) Align your Mailbox on top of Cross Arm and mark front and back locations of mailbox mounting holes (See Figure 5).
2) Remove mailbox and center U-brackets where marks were made for location of mounting holes.
3) Secure Brackets to Cross Arm at pre-marked locations with # 8 Self Drilling screws. Use (2) screws for each U-Bracket.
3) Set Mailbox on top of U -Brackets and align Mailbox holes with U-Bracket holes on Side of Mailbox or through Base/Floor of mailbox.
4) Secure Mailbox to U-brackets with #10-24 threaded screws and nuts.
IF YOU HAVE ANY PROBLEM WITH THIS PRODUCT, PLEASE DO NOT RETURN TO RETAILER. CALL OR EMAIL OUR CUSTOMER SERVICE DEPARTMENT
AND WE WILL PROVIDE IMMEDIATE ASSISTANCE.
CREATIVE SOLUTIONS, LLC Postal Pro Mailboxes HATTIESBURG, MISSISSIPPI
Email: [e-mail] Phone: [phone] WEBSITE: POSTALPROMAILBOXES.COM
Double Mount Option
The PP200 Post Kit can be
used to Support (2)
Mailboxes. Simply push the
Cross Arm through the
Vertical Post so that
approximately 12 inches
extend on both sides.
A separately purchased
Mailbox Mounting Board will
be needed for each
mailbox for a double mount
configuration. Wooden or
Plastic Mounting boards
are available at most
Home Improvement Centers.
Figure 5
Option 1: Mount Mailbox
Screws on Side of Mailbox
Option 2: Mount Mailbox
Screws through base/Floor
of Mailbox
Screws
Screws