quadient IS-420 User manual

INSTALL AND CONNECT THE ELEMENTS: 1Hand feed table,
2Base, 3Catch tray.
CONNECT THE LAN to a network RJ45 plug of the Base and
to the LAN wall socket using the LAN cable B.
If included in your system, CONNECT THE SCALE (see its
Quick Install Guide).
OPEN THE BASE COVER,remove the headset protecting
strips and insert the headset in its compartment, then push
the headset back until it clicks.
WRITE DOWN THE PSD number, you may need the number
later. INSTALL THE PSD in one of the slots then close the cover. CONNECT THE SYSTEM POWERPLUG. Follow the installation wizard on the screen. Refer to the installation section in the User Guide.
IS-420 QUICK INSTALLATION GUIDE
CAUTION: use a solid and steady table, far
from any door or fan.
7
4
8
5
3
6
2
3
1
C
BC
A
1Check the box contents.
2
For more information about your mailing
system, please visit:
kb.quadient.co.uk/is420_ug

1
3
4
2a
2b
For more specific information about your
mailing system, see the User Guide.
Press Clear or Wake
To reset previous settings...
Choose rate and services
When the weight is displayed...
Consumables,
contact Quadient Supplies:
0845 880 0002
For your installation Pin Code please visit
www.quadient.co.uk
Put your mail on the scale
To weigh your mail...
or
Enter the weight manually
Shortcut keys
Getting to know your mailing system
Applying postage
Changing the ink cartridge
Screen main areas
1
2
1
2
If needed, press to get back to the
home screen.
To get back to default rate settings,
press on the keyboard.
If the system is asleep, press to
wake it up with default settings.
1
2
3
Current rate and select-
ed services are
displayed in this zone of
the screen.
Rate and services (to change: K1)
Date printed (to change: K4)
Weighing type (to change: K6)
Imprint position oset
Postage and weight
Job memory (can contain rate, stamp settings
and account)
Current account
D1
D2
D3
D4
D5
D6
D7
K1
K2
K3
K4
K5
K6
K7
K8
K9
Rates and services selection
Memorized jobs (rate, stamp settings, account)
Credit management
Type of imprint and Imprint settings
Label printing
Weighing modes
Sleep / wake (amber / green)
Stops printing
Starts printing
Check that the D3 icon is .
Otherwise, press and then select the
option Standard weighing.
Press and then select the option
Manual weight entry.
Enter the weight and press OK.
Press OK to validate your selection and
return to the home screen.
Use the keypad to select an available Class
and/or Services, or select key 8 for the
wizard.
To change the rate and/or add services:
Press .
The rate selection
screen is displayed.
1
2
On the new ink cartridge,
remove the protective
strips from the printing
heads.
Raise base cover and
follow instructions printed
on sticker inside.
Print the stamp
To print on labels
When the postage is displayed...
1
2
If you want to print on a label, see the alterna-
tive sequence below.
Press to start the motors of your mail-
ing system.
Insert the mail piece in
the mail path, the
imprint printing
position on the upper
right side.
Insert labels into the
dispenser until a click,
printing side facing
the right.
Press to enter the number of
labels to print and then press .
1
2
If jamming occurs... Adding credit
Press , type 2 and follow the instructions
onscreen.
Note: to complete this operation successfully, your postal
services account must have a positive credit balance of
the corresponding amount.
Press on the control
panel to stop the motor.
Under the base, lift up
the release handle and,
using your other hand,
remove stuck envelope
or labels.
1
2
K7
K8
K9
K4
K1
K2 K5
K6
K3
A0021368/C - 31/03/2020
D5
D6
D7D4
D3
D2
D1
IS-420