Crestron HD-DA-4KZ-E Series Dimensional drawing

DO GUIDE
HD-DAx-4KZ-E Series
4K60 4:4:4 HDR Distribution Ampliers
DO Connect the Device
Connect the device as required for the application.
Front Panel Connections (HD-DA2-4KZ-E Shown)
DO Select the EDID Mode
Select the EDID (Extended Display Identication Data) mode by moving the EDID switch to either
of the following positions:
•DEFAULT: (Default setting) The device sends a predened Crestron EDID to the
input device. The Crestron EDID supports 2-channel LPCM audio and
4K60 444 non-HDR video.
•COPY 1ST: The device copies the EDID of the display connected to OUTPUT 1 and
sends the EDID to the input device.
NOTE: If the display that is connected to OUTPUT 1 is disconnected, the current EDID
is retained. Connecting a different display to OUTPUT 1 does not automatically update
the EDID at the input device. To update the EDID, move the EDID switch to the DEFAULT
position and then back to the COPY 1ST position.
EDID Selection Switch (HD-DA2-4KZ-E Shown)
DO Install the Device
The Crestron®HD-DAx-4KZ-E Series consists of the HD-DA2-4KZ-E, HD-DA4-4KZ-E, and
HD-DA8-4KZ-E. The devices can be mounted onto a at surface or onto a rack rail.
Mount onto a Flat Surface
Using four mounting screws (not included), mount the device onto a at surface such as a wall.
Wall Mounting (HD-DA2-4KZ-E Shown)
Mount onto a Rack Rail
Mount the device onto a front or rear rail of a rack. Position either the left or right mounting ange of
the device so that the holes align with the holes in the rack. Then, secure the device to the rack using
two rack mounting screws (not included).
Rail Mounting (HD-DA2-4KZ-E Shown)
DO Check the Box
QTY ITEM PART NUM.
1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2037209
INPUT:
From HDMI®
audio/video
source
OUTPUT 1:
To HDMI
display
OUTPUT 2:
To HDMI
display
SERVICE:
For rmware
loading
24 V 0.75 A:
From included
power pack

DO GUIDE DOC. 8276A (2050984) 04.18
Specications subject to change without notice.
DO Select the HDCP Version
Select the HDCP version by moving the HDCP switch to one of the following positions:
• OFF: Disables HDCP support
• 1.4: Sets the HDCP version to 1.4
• 2.2: (Default setting) Sets the HDCP version to 2.2
HDCP Selection Switch (HD-DA2-4KZ-E Shown)
DO Observe the LEDs
Observe the LEDs on the rear panel of the device:
•PWR: Lights amber to indicate that the device is booting, and lights green to indicate that
the device is powered on
•INPUT: Lights green to indicate that an HDMI signal is detected at the HDMI input
•OUTPUT 1-2, 1-4, or 1-8: Lights green to indicate that the corresponding HDMI output is
transmitting an HDMI signal
In addition to the LEDs listed above, a SETUP LED is also provided. When the SETUP button is
pressed for 10 seconds, the SETUP LED ashes red ten times to indicate that the default settings
have been restored.
Rear Panel LEDs (HD-DA2-4KZ-E Shown)
DO Learn More
Visit the website for additional information and
the latest rmware updates. To learn more about
this product, use a QR reader application on your
mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.
The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
Certain Crestron products contain open source software. For specic information, visit www.crestron.com/legal/open-source-software.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United States and/or other countries. HDMI and the HDMI logo are either
trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible
for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.
HD-DA2-4KZ-E HD-DA4-4KZ-E HD-DA8-4KZ-E