Crestron DM-TXRX-100-STR Dimensional drawing

DO GUIDE
DO Make Connections to the Device
Make connections to the front and rear panels of the device as required for the application (refer
to illustrations and ).
Front Panel Connections
Rear Panel Connections
NOTE: The LAN PoE (Power over Ethernet) port is a PoE PD (Powered Device) port. To receive
PoE, the DM-TXRX-100-STR requires connection to a PoE PSE (Power Sourcing Equipment)
port of a PoE switch. Any wiring that is connected to a PoE PSE port is for intrabuilding use only
and should not be connected to a line that runs outside of the building in which the PSE
is located.
NOTE: Connection to the included power pack is not required if PoE is used to power the
device.
DM-TXRX-100-STR
HD Streaming Transmitter/Receiver
DO Install the Device
The Crestron®DM-TXRX-100-STR can be mounted onto a at surface or onto a rack rail.
Mounting onto a Flat Surface
Using four mounting screws (not included), mount the device onto a at surface such as a wall
(refer to illustration ) or the underside of a table.
Mounting onto a Wall
Mounting onto a Rack Rail
Using two mounting screws (not included), mount the left or right mounting ange of the device
onto the front or rear rail of a rack (refer to illustration ).
Mounting onto a Rack Rail
DO Check the Box
QTY PRODUCT PART NUM.
1 Cable, RJ-45 Male - DB9 Female, 6' (1.83 m) 2043246
1Connector, 4-Pin 2003576
1Connector, 5-Pin 2003577
1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2037209
Not Included: Mounting Screws, USB Mass Storage Device, IR Cables or Emitters, and USB, Data Communications, HDMI, and Ethernet Cables
From Power Pack
(Included)
From USB Mass
Storage Device
(For Firmware Loading)
From HDMI®
Audio/Video
Source
To HDMI
Display
To /From
10BASE-T/100BASE-TX
802.3af PoE
Power Sourcing
Equipment
Ground
To/From
RS-232
Device
To IR
Controllable
Devices
To/From
USB Port
on PC
To/From
Serial Port
on PC
(Cable Included)

DO GUIDE DOC. 7620B (2043777) 09.15
Specications subject to change without notice.
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specic patents that cover Crestron products are listed at patents.crestron.com. The product warranty can be found at www.crestron.com/warranty.
Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDMI and the HDMI logo are either
trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible
for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
DO Congure the Device
Using the web interface, congure the device. To access the web interface, open a web browser
and then go to the IP address of the device.
NOTE: By default, DHCP is enabled. To display the IP address on the connected display, press
the SETUP button on the front panel of the device.
To log in to the user interface, enter the user name and password. The default user name is
admin, and the default password is admin.