Crestron Aspire IC8DT User manual

Aspire™ In-Ceiling Speakers
quickstart guide
IC8DT
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
IC8DT
Mount/Remove Speakers
The in-ceiling speakers include three toggle clamps that simplify the mounting process. If the
grilles are mounted on the speakers, remove them before proceeding. (Refer to
“Install/Remove Grilles”, below.)
1. Connect the speaker cable wires to the spring terminals by pressing the top of the
terminals down and inserting the exposed strands into the hole. Make sure that left and
right channels are connected to the left and right tweeter terminals, respectively, and that
the +wires go to the +(red coded) terminals, and the –wires go to the –(black coded)
terminals.
2. With the toggle clamps turned inward, insert the speaker into the opening. As the three
screws on the front of the speaker are tightened, the toggle clamps first rotate into
clamping position (refer to the figure to the right) and then begin holding the speaker to
the ceiling. Tighten the screws until the speaker is secured; do not overtighten.
3. Speaker removal is accomplished by reversing the procedures given in steps 1 and 2
above.
a. Loosen the front screws to unclamp the speaker. Continue to loosen the screws until
the toggle clamps rotate inward.
b. When the speaker is loose, carefully remove it from the opening.
c. Disconnect the wires from the terminals.
Install/Remove Grilles
The zero-bezel frameless grilles are held in place by powerful magnets. To remove the grilles,
grip the edges and pull away from the speaker.
Paint the Speaker Grilles
Speaker grille painting should be done prior to mounting.
1. Carefully remove the material on the underside of the grilles and set them aside for
reinstallation. It may be necessary to use a knife or other sharp instrument to free an edge
of the material so it can be peeled away. Use care to avoid cutting or tearing the material.
2. Dry brush or lightly spray the surface to be painted. Use care to avoid clogging the holes in
the grilles.
3. Once the paint is dry, reinstall the material to the underside.
1
The product of expert Crestron®audio engineering,
Aspire™ speakers deliver high-end performance for
demanding residential installations. Select materials
and a refined appearance underscore the
meticulous design behind each model. The result is
a complete line of in-wall and in-ceiling speakers
worthy of a place in every room of the finest custom
home.
The Aspire IC8DT model is a single in-ceiling
loudspeaker featuring an 8 inch dual voice coil
woofer and dual 1 inch dome tweeters. It is
designed to produce stereo sound in the space of a
single speaker, perfect for bathrooms and other
small spaces.
QUICKSTART DOC. 7391B (2034591) 12.12
Install Cables
Run the cables from the audio source to the speaker location following all appropriate local
codes. Strip the ends of the speaker cable wires 1/4” to 1/2” (6 mm to 12 mm) and twist the
exposed strands.
Rear View Spring
Terminals (4)
Toggle
Clamps (3)
Front View
Tighten
Screws
1
1Installation
Determine Placement In Room
90°
Prepare Mounting Holes
Speaker placement is largely a matter of personal preference. However, placing the speaker
near a corner or wall will extend its low frequency response.
Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air
ducts, joists, or other possible obstructions. Use a good quality stud finder to locate joists.
If there is no access to the area above the ceiling, and it is uncertain that there are no
obstructions, carefully drill a small hole just through the ceiling near the middle of the proposed
speaker location(s) and use one of the commercially available inspection devices designed for
this purpose, or do one of the following:
● Use a piece of stiff wire, bent into an “L” shape, with one end long enough to explore an
area equal to the size of the speaker with the toggle clamps extended. Insert the wire into
the hole, make sure it rotates freely in a complete circle and that there is sufficient depth,
or
● Use a drywall saw to cut a small hole at a 45° angle toward the inside of the hole. An
angle cut simplifies repair since the removed piece can be reinserted to help plug the hole.
If there are no obstructions, use the supplied template to trace outlines of the mounting holes
on the ceiling. Cut the final mounting holes at a 90° angle to the ceiling.
45°

Aspire™ In-Ceiling Speakers
quickstart guide
IC8DT
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
IC8DT
The specific patents that cover Crestron products are listed online at patents.crestron.com
Crestron, the Crestron logo and ASPIRE are either trademarks or registered trademarks of Crestron Electronics,
Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may
be used in this document to refer to either the entities claiming the marks and names or their products. Crestron
disclaims proprietary interest in the marks and names of others.
©2012 Crestron Electronics, Inc.
3
Specifications
QUICKSTART DOC. 7391B (2034591) 12.12
2
SPECIFICATION
Features & Performance
Woofer
Tweeter
Crossovers
Crossover Frequency
Environmental
Temperature
Humidity
IC8DT Specifications
Weight*
Impedance
Frequency Response
Frequency Range
Power Handling
Sensitivity
Construction
Baffle
Grille
Mounting
Dual voice coil 8 in (203 mm) woven poly-glass composite
with rubber surround, vented pole piece and steel basket
(2) 0.98 in (25 mm) advanced synthetic polymer dome,
ferrofluid cooling, post mounted
4th order hybrid
2.5 kHz
8 Ω nominal per channel
48 Hz - 20 kHz (±3 dB)
40 Hz to 20 kHz (-10 dB)
100 watts program per channel
89.5 dB @ (W/m) per channel
DETAIL
11.64 in (296 mm)
4.66 in (119 mm)
4.47 in (114 mm)
10.80 in (275 mm)
7.55 lb (3.4 kg)
2
ABS plastic, black
Steel with textured finish, paintable, magnetically held zero
bezel frameless
Flush ceiling mount using three integral spring-loaded toggle
clamps, 1.35 in (34 mm) maximum surface thickness
41° to 104° F (5° to 40° C)
10% to 90% RH (non-condensing)
For indoor use only
Connections
Input
Maximum Wire Size
(2 sets of 2) spring terminals
10 AWG
Available Models
ASPIRE ICDT-W-T
Available Accessories
SPKA-NCTP-IC800
Aspire 8” 2-Way Single-Point Stereo In-Ceiling Speaker,
White Textured
New-Construction Speaker Templates
Rear and Side Views
Diameter
Depth
Minimum
Mounting
Depth
Recommended
Cutout
Diameter
Dimensions*
Diameter
Depth
Minimum Mounting Depth
Recommended cutout
diameter
* Dimensions shown are per speaker
The following table provides corrective action for possible trouble situations.
If further assistance is required, please contact a Crestron customer service
representative.
Further Inquiries
Future Updates
TROUBLE POSSIBLE CAUSE(S)
CORRECTIVE ACTION
No sound or
intermittent
sound from
speakers.
Cable connection
error.
Verify cable connections
between amplifier and speakers.
Amplifier not receiving
input signal or amplifier
malfunction.
Verify amplifier is functioning correctly,
that it is receiving an input signal and
that correct input source is selected.
Faulty device in system. Verify all devices in system are
functioning properly.
Constant
noise such as
buzz, hum, or
hiss from
speakers.
System grounding fault. Verify system grounding.
Poor low
frequency
output.
Incorrect polarity
connection at speaker.
Verify speaker connection polarity
(+ on speaker to + on amplifier).
Problem Solving
Troubleshooting
To locate specific information or resolve questions after reviewing this guide,
contact Crestron's True Blue Support at 1-888-CRESTRON [1-888-273-7876]
or refer to the listing of Crestron worldwide offices on the Crestron Web site
(www.crestron.com/offices) for assistance within a particular geographic region.
To post a question about Crestron products, log onto the Online Help section of
the Crestron Web site (www.crestron.com/onlinehelp). First-time users must
establish a user account to fully benefit from all available features.
As Crestron improves functions, adds new features and extends the
capabilities of the Aspire IC8DT, additional information may be made
available as manual updates. These updates are solely electronic and serve
as intermediary supplements prior to the release of a complete technical
documentation revision.
Check the Crestron Web site periodically for manual update avail ability and
its relevance. Updates are identified as an “Addendum” in the Download
column.