Crestron ULTIMATE OD6T-BRZ-T-EACH User manual

The Crestron® Ultimate speakers ULTIMATE OD6T-BRZ-T-EACH and
ULTIMATE OD6T-PRIMED-EACH made by Origin Acoustics deliver the
pinnacle of performance for demanding outdoor installations. Select
materials, top shelf components, and a high-end appearance underscore
the design behind each speaker. The result is a no-compromise outdoor
speaker designed to be staked directly into the ground or mounted to an
exterior wall, fence post, or tree. The ULTIMATE OD6T-PRIMED-EACH
speaker can be painted to blend with the surroundings.
In the Box
1 Ultimate 6 in. 2-Way Outdoor Speaker (6511868 or
6511869)
 
Additional Items
2 Wire nuts
Installation
Prepare the Site
The Crestron Ultimate speakers ULTIMATE OD6T-BRZ-T-EACH and
ULTIMATE OD6T-PRIMED-EACH can be installed at ground level using
stakes (not included). They can also be mounted to outdoor hard
surfaces, such as a trellis, under an eave, on a wall, on a deck, or to a
post using the surface/tree mounts (not included).
lFor in-ground level installation, choose a location that will not flood
and where the speaker will not be affected by an in-ground sprinkler
system.
lFor above-ground installation, mount the speaker with either the
surface or tree mounting bracket (not included).
ULTIMATE OD6T-BRZ-T-EACH and ULTIMATE OD6T-PRIMED-EACH QuickStart
Ultimate 6 in. 2-Way Outdoor Speaker, Ribbon Tweeter, Single
1

Mount the speaker
In-Ground Installation
Use the SPKA-STAKE-OD-18 optional speaker stake to install the
speakers at ground level. This accessory must be purchased separately.
For in-ground installation:
1. Pull the speaker cable through the top of the stake and out either
side on the bottom opening.
2. Drive the ground stake (not included) into the ground.
lFor installation in soft soil: The stake can be installed without
excavating the soil. Push the stake down into the soil.
lFor installation in hard soil: Dig a hole for the stake. Place the
stake in the hole with the top cylinder of the stake above ground
level. Hold the stake straight while backfilling and compacting the
soil.
3. Attach the speaker to the stake by turning the speaker clockwise
until it is mounted properly.
2
ULTIMATE OD6T-BRZ-T-EACH and ULTIMATE OD6T-PRIMED-EACH QuickStart
Ultimate 6 in. 2-Way Outdoor Speaker, Ribbon Tweeter, Single


Above-Ground Installation
Use the SPKA-SMK/TREEMK-ULTIMATE-OD6 optional accessory to
install the speakers on a surface or a tree. This accessory must be
purchased separately.
For surface mount installation:
1. Select a suitable mounting location to mount the surface mount
bracket.
2. Install the surface mount bracket as follows:
a. Place the surface mount bracket (not included) in the mounting
location.
b. Hold the surface mount bracket against the surface to mark the
screw holes.
c. Drill holes at the marked screw hole locations and install three
anchors (not included).
d. Route the speaker cable through the center hole and out of the
cable opening on the surface mount bracket.
e. Secure the surface mount bracket to the surface using drywall
screws (not included).
3. Attach the speaker to the surface mount bracket by hand threading
the speaker to the surface mount bracket.
4. For optimal sound coverage, adjust the speaker left or right and up or
down.
a. Adjust the speaker left or right by first loosening the nut. Adjust
the angle to the desired position, then retighten the nut.
b. Adjust the speaker up or down by first loosening the allen screw
on the knuckle adapter bracket. Adjust the angle to the desired
position, then retighten the screw.
3
ULTIMATE OD6T-BRZ-T-EACH and ULTIMATE OD6T-PRIMED-EACH QuickStart
Ultimate 6 in. 2-Way Outdoor Speaker, Ribbon Tweeter, Single

For tree mount installation:
1. Install the tree mount bracket as follows:
a. Place the tree mount bracket (not included) in the mounting
location.
b. Hold the tree mount bracket against the surface to mark the
screw holes.
c. Drill holes at the marked screw hole locations and install three
anchors (not included).
d. Route the speaker cable through the center hole and out of the
cable opening on the tree mount bracket.
e. Secure the tree mount bracket (not included) to a tree using
drywall screws (not included).
2. Attach the speaker to the tree mount bracket by hand threading the
speaker to the tree mount bracket.
3. For optimal sound coverage, adjust the speaker left or right and up or
down.
a. Adjust the speaker left or right by first loosening the nut. Adjust
the angle to the desired position, then retighten the nut.
b. Adjust the speaker up or down by first loosening the allen screw
on the knuckle adapter bracket. Adjust the angle to the desired
position, then retighten the screw.
4
ULTIMATE OD6T-BRZ-T-EACH and ULTIMATE OD6T-PRIMED-EACH QuickStart
Ultimate 6 in. 2-Way Outdoor Speaker, Ribbon Tweeter, Single

Connect the Speaker Cable
1. Run the speaker cable (not included) from theaudio source to the
wire nut, observing all appropriate local codes.
2. Run the speaker cable from the speaker location to the wire nut,
observing all appropriate local codes.
NOTES:
lThe speaker includes a hardwired direct-burial speaker cable.
lMake sure that the positive cable is attached to the red
connection, and the negative cable is attached to the black
connection for 70V/100V installation (see Figure C).
lMake sure that the positive cable is attached to the blue
connection, and the negative cable is attached to the brown
connection for 8 ohm installation (see Figure D).
3. Combine and twist the positive (+) cables together in a clockwise
motion. Repeat this step for the negative (-) cables.
4. Secure the two cables together using the wire nuts ensuring that no
copper is exposed.
5
ULTIMATE OD6T-BRZ-T-EACH and ULTIMATE OD6T-PRIMED-EACH QuickStart
Ultimate 6 in. 2-Way Outdoor Speaker, Ribbon Tweeter, Single

6
ULTIMATE OD6T-BRZ-T-EACH and ULTIMATE OD6T-PRIMED-EACH QuickStart
Ultimate 6 in. 2-Way Outdoor Speaker, Ribbon Tweeter, Single

Visit the Product Page
Scan the QR code to visit the product page.
ULTIMATE OD6T-BRZ-T-EACH
https://www.crestron.com/model/6511868

ULTIMATE OD6T-PRIMED-EACH
https://www.crestron.com/model/6511869

Additional Information

Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Regulatory Model: M202046011
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. Origin Acoustics is
either a trademark or registered trademark of Origin Acoustics, Inc. in the United States
and/or other countries. Other trademarks, registered trademarks, and trade names may
be used in this document to refer to either the entities claiming the marks and names or
their products. Crestron disclaims any proprietary interest in the marks and names of
others. Crestron is not responsible for errors in typography or photography.

©2021 Crestron Electronics, Inc.
Doc. 9039A
08/20/21
7
ULTIMATE OD6T-BRZ-T-EACH and ULTIMATE OD6T-PRIMED-EACH QuickStart
Ultimate 6 in. 2-Way Outdoor Speaker, Ribbon Tweeter, Single