Crestron CHV-TSTATEX User manual

1
quickstart guide
CHV-TSTATEX
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
CHV-TSTATEX
For details, refer to the latest version of the
CHV-TSTATEX Operations & Installation Guide, Doc. 6989.
QUICKSTART DOC. 6990B (2027559) 01.12
infiNET EX®Thermostat
DIP Switch Settings
# DESCRIPTION
4 System Type Heat/Cool Heat Pump
3 Heat Pump Mode Aux Heat Dual Fuel
2 Cool/HP Stages 1 2
1 Heat Stages 1 2
ON OFF
# DESCRIPTION
4 Fan In Heat Disabled Enabled
3 Change Over Outputs Disabled Enabled
2 Cool SP Range Normal Extended
1 N/A N/A N/A
ON OFF
LEFT SWITCH
RIGHT SWITCH
STEAL
(LEFT)
24VAC
(RIGHT)
Power Steal Switch
ON
1 2 3 4
1 2 3 4
ON
Single Stage Heat-Only Application Single Stage Cool-Only Application
Mount the thermostat directly to
drywall or to a single-gang box in
accordance with accepted building
codes and practices. If using the
single-gang box, be sure to fill it with
thermal insulation material.
For additional details and installation
options, refer to the latest version of
the CHV-TSTATEX Operations &
Installation Guide (Doc. 6989). It is
available from the Crestron® Web site
(www.crestron.com/manuals).
Mounting
1
2
Connections
Connect the thermostat using the four most typical wiring configurations shown below as a guide. Refer to“DIP Switch Settings” on the left to
configure each application. For more information, refer to the latest version of the CHV-TSTATEX Operations & Installation Guide (Doc. 6989).
Heat Pump Application With
Integrated Controller Heat - Cool Application With
Integrated Control Unit
Transformer
Heat
Relay
Optional, for power
R
C
System
DIP Switch Settings
ON
1 2 3 4
1 2 3 4
ON
R
C
C
Y
G
R
Compressor
Relay
Fan
Relay
DIP Switch Settings
ON
1 2 3 4
1 2 3 4
ON
R
C
C
W
Y
G
R
Optional, for power
RH and RC must be
jumpered together.
Heat
Relay
Fan
Relay
Cool
Relay
DIP Switch Settings
ON
1 2 3 4
1 2 3 4
ON
R
C
C
Y
G
O
E - U - W
R
Compressor
Relay
Fan
Relay
Changeover
Valve
Aux Heat
Relay
RH and RC must be
jumpered together.
DIP Switch Settings
ON
1 2 3 4 1 2 3 4
ON
Optional, for power
Optional,
for power
System
Transformer
System
Transformer
System
Transformer

2
quickstart guide
CHV-TSTATEX
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
CHV-TSTATEX
For details, refer to the latest version of the
CHV-TSTATEX Operations & Installation Guide, Doc. 6989.
QUICKSTART DOC. 6990B (2027559) 01.12
infiNET EX®Thermostat
13Basic Thermostat Setup 5System Modes and Fan Operation
4Basic infiNET EX®Setup
Use k or jto choose the temperature units: F (Fahrenheit),
C1 (Celcius, whole degree set points), or C2 (Celcius, half
degree set points).
F
AUTO
H
C
F
HOLDAUTO
H
C
F
A
OFF
FAN IN AUTO MODE
SYSTEM OFF
HOLD MODE
AMBIENT
TEMPERATURE
SET
POINT
HEAT MODE
COOL MODE ALWAYS
DISPLAYED
AUX HEAT CALL
FAN CALL
COOL CALL
HEAT CALL
FAHRENHEIT
CELSIUS
Press the MODE button to cycle the unit
through available modes: Off, Heat,
Emergency Heat (for heat pump and dual-fuel
systems), Cool, and Auto.1
• Mode changes take place upon release of
the MODE button.
• The selected mode becomes operational
three seconds after the mode has been
entered.
Press the FAN button to toggle between Fan
Auto and Fan Always On modes.
• The fan icon is always displayed.
• When set to Fan Auto, the fan operates only
when there is a cool or heat call.1, 2
• In system Off mode, the fan still runs if
set to Fan Always On mode.
Press MODE and FAN simultaneously to enter
Hold mode. Hold mode ignores scheduled set
point values from the control system.
Use the k and jbuttons to choose the
desired temperature set point.
Thermostat Display Key
Typical Heat
Mode Display
AUTO
OFF
F
AUTO
C
F
Typical Cool
Mode Display
Typical Off
Mode Display
Install two AA batteries in the battery compartment. 1
CAUTION: Replace all batteries in the CHV-TSTATEX at the same time. Mixing old
and new batteries in the CHV-TSTATEX may result in battery leakage and
equipment damage.
To enter Setup mode2, press and hold FAN, then simultaneously press and hold k
and jfor about five seconds.The display shows the Temperature Scale function
(FC).
F
AUTO
A
Typical
Emergency Heat
Mode Display
1. Refer to the latest version of the CHV-TSTATEX Operations & Installation Guide
(Doc. 6989) for detailed information on setup and operating modes.
2. Fan only runs during heat calls if the thermostat has been configured to do so.
1. Expected battery life is 1 year using quality alkaline batteries.
2. Refer to the latest version of the CHV-TSTATEX Operations & Installation Guide (Doc. 6989) for detailed
information on setup and operating modes.
Flashing
F
AUTO
A
Typical
Auto Heat/Cool
Mode Display
In Setup mode,press MODE until the infiNET EX ID (RF ID)
function is displayed (id). Use k and jto choose the infiNET
EX ID. Press MODE until the Start infiNET EX Acquire function is
displayed (AC).
Put an infiNET EX gateway (e.g., CEN-RFGW-EX or MC3) into
Acquire mode, from the unit itself or from Crestron Toolbox™, as
described in the latest revision of the CEN-RFGW-EX Operations
& Installation Guide (Doc. 6706) or MC3 Operations &
Installation Guide (Doc. 7095).
Press k or jto start the acquire process: display shows flashing - - (in progress).
When finished, display shows 00 (finished, found gateway) or E# (finished, could not
find gateway), where # represents an error code.
Once all devices have been acquired, take the CEN-RFGW-EX or MC3 out of Acquire
mode. Press FAN on the thermostat to exit Setup mode. The specific patents that cover Crestron products are listed at www.crestronpatents.com.
Crestron, the Crestron logo Crestron Toolbox and infiNET EX are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their
products. Crestron disclaims proprietary interest in the marks and names of others.
©2012 Crestron Electronics, Inc.
!