Crestron CHV-TSTAT-FCU-PIR-10 Owner's manual

CHV-TSTAT-FCU-PIR-10
Heating and Cooling Fan-Coil Thermostat
Supplemental Guide
Crestron Electronics, Inc.

The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible
for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2017 Crestron Electronics, Inc.

Supplemental Guide – DOC. 7964A Contents
•
i
Contents
Introduction 1
Set Up the Thermostat 1
Enter Setup Mode................................................................................................... 1
Navigate Setup Mode ............................................................................................. 1
Configure the Thermostat........................................................................................ 2

Supplemental Guide – DOC. 7964A CHV-TSTAT-FCU-PIR-10: Heating and Cooling Fan-Coil Thermostat
•
1
CHV-TSTAT-FCU-PIR-10: Heating and
Cooling Fan-Coil Thermostat
Introduction
After installation, the Crestron®CHV-TSTAT-FCU-PIR-10 needs to be set up. Refer to the
information that follows for an overview of the setup procedure.
For more information on the CHV-TSTAT-FCU-PIR-10, refer to the
CHV-TSTAT-FCU-PIR-10 DO Guide (Doc. 7915).
Set Up the Thermostat
A qualified technician should set up the thermostat locally. Navigate through the setup
screens and make the changes necessary for the HVAC system.
In most cases, default functionality is sufficient to run the system.
Enter Setup Mode
Press and hold the down button. While holding the down button, simultaneously press and
hold the mode and fan buttons until the SETUP: SYSTEM screen is displayed.
NOTE:
To exit Setup mode, press and hold the down button. While holding the down
button, simultaneously press and hold the mode and fan buttons until the main screen is
displayed.
SETUP: SYSTEM Screen
Navigate Setup Mode
When the device is in setup mode, press the MODE button to advance to the next screen,
press the FAN button to scroll vertically through the setup options on the screen, and press
the up and down buttons to change the value for the selected item.

2
•
CHV-TSTAT-FCU-PIR-10: Heating and Cooling Fan-Coil Thermostat Supplemental Guide – DOC. 7964A
Configure the Thermostat
SETUP: SYSTEM Screen
Use the Heat Type option to select the type of HVAC system that the thermostat is
controlling.
SETUP: SYSTEM PERF Screen
Use the Heat Anticipator and Cool Anticipator to control the steady-state regulation band
size. A lower setting results in more frequent cycles and faster response; a high setting
results in less frequent cycles and a slower response.
SETUP: DEVICE OPTS Screen
The Network ID must match the NET ID specified in the system program.
Use the LCD Contrast to change the contrast of the LCD screen.
BOOKED TIMEOUT Screen
The BOOKED TIMEOUT determines how long the room must be empty, as determined by
the PIR, before the room enters the vacant state. Vacancy state is defined in the control
system program.

Supplemental Guide – DOC. 7964A CHV-TSTAT-FCU-PIR-10: Heating and Cooling Fan-Coil Thermostat
•
3
UNBOOKED TIMEOUT Screen
The UNBOOKED TIMEOUT determines how long the room must be empty, as determined
by the PIR, before the room enters the vacant state. Vacancy state is defined in the control
system program.
SETUP: MIN/MAX Screen
Set the minimum (Min) and maximum (Max) temperature set point for HEAT, COOL, and
AUTO modes.
SETUP: SERVICE/TEST Screen
The SETUP: SERVICE/TEST screen allows testing of the unit while bypassing all system
delays. The Heat, Cool, and Fan calls are settable via 0.1 V increments. When the device
operates as a relay, Heat Call is relegated to ON or OFF.
The PIR displays DETECTED when motion is detected.
SETUP: DISP OPTIONS Screen
The SETUP: DISP OPTIONS screen allows adjusting of both the displayed and the
regulated temperatures.

4
•
CHV-TSTAT-FCU-PIR-10: Heating and Cooling Fan-Coil Thermostat Supplemental Guide – DOC. 7964A
SETUP: FAN VOLTAGE Screen
Use the SETUP: FAN VOLTAGE screen to select the voltages corresponding to the high,
medium, and low fan speeds.

Supplemental Guide – DOC. 7964A CHV-TSTAT-FCU-PIR-10: Heating and Cooling Fan-Coil Thermostat
•
5
This page is intentionally left blank.

Crestron Electronics, Inc. Supplemental Guide – DOC. 7964A
15 Volvo Drive Rockleigh, NJ 07647 (2048038)
Tel: 888.CRESTRON 01.17
Fax: [phone] Specifications subject to
www.crestron.com change without notice.