CrimeStopper Cool Start RS-7 User manual

RS-7 2WAYSYSTEMS
REMOTEENGINESTARTINGSYSTEM
INSTALLATION INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS onyourchoiceofa“CoolStart”SystemwithDataPortTechnologyfordirectconnectiontobypass
modulebyCrimestopperSecurityProductsInc.Thisbookletcontainstheinformationnecessaryforinstallingyourremote
starter system.Ifanyquestionsarise,contactyourinstallationdealerorCrimestopperSecurityProductsInc.attheTech
Support number below.
DISCLAIMER:
Thisinstallation bookisdesigned for the installer or individualwithan existing understanding ofautomotiveelectrical
systems,along withthe abilitytotestand connectwiresfor proper operation.Toeaseinstallation,wesuggestthatyou
READ THISMANUAL before beginning your installation.Thisbookisprovided asaGENERALGUIDELINEand the
informationcontainedhereinmaydifferfromyourvehicle.CrimestopperSecurityProducts,Inc.andits’vendorsshallnot
beliableforanyaccidentresultingfromtheuseofthisproduct. Thissystemisdesignedtobeprofessionallyinstalledinto
avehicleinwhichall systemsand associated componentsare inperfect working condition.
TECHNICALSUPPORT:[phone]
Monday-Friday8:00am-4:30pmPacificStd. Time
Web Site: www.crimestopper.com
E-mail: [e-mail]
CRIMESTOPPERSECURITYPRODUCTS, INC.
1770 S. TAPO STREET, SIMIVALLEY, CA. 93063
REV 02-2009
ThisdevicecomplieswithFCC Rulespart15.Operationissubjectto
the following twoconditions:(1)Thisdevicemaynotcauseharmful
interference,and (2)Thisdevicemustacceptanyinterferencethat
maybe recei
ved,including interferencethatmaycauseundesired
operation. The manufacturerisnot responsibleforanyradioorTV
interferencecaused byunauthorized modificationstothisequipment.
Suchmodification couldvoidthe user’sauthoritytousethe
equi
pment.

2
TABLEOF CONTENTS
Pre-Installation Considerations….………...……...………………………………………………………………..….………..2
Installation Cautions&Warnings………………………………………………………………………………..….....……..…3
Wiring……..……………………....…………………………………………………………………………………...………...3-7
Wiring High-Current Wiring…..…….…………………………………………………………………………....….….............8
Power Door Lock Wiring...…………………………………….…………….……..…………...….…………..…..………..9-10
Smart Tachless, TachReference, TachFinder, &Timed CrankModes…………………..…..…….…......…………11-14
DieselGlowPlug Delay..………………….……………………………...……………………...…..…………..…….………15
OptionsProgramming ………..……………………….……………………………..……………..…….....….….....……15-20
Transmitter / Transceiver Programming……………………….……………….….…………..………...…..…..…….....21-22
Troubleshooting “Before You Call”Section……………..……………………………...………….……….……..….………22
ManualTransmission Mode……………………….………………………………...…………………….….……..…………23
Jumper PINDiagram……………………………….………………………………...…………………….….……..…………24
Antenna Diagram……………………….…………………………………………………………..………………………..….25
LowCurrent Plug……………………………………………………..………………………………..………..….……….…..26
High Current Plug………………………………..………………………………………………………………..……….……27
PRE-INSTALLATIONCONSIDERATIONS
BEFORE BEGINNING,check all vehiclemanufacturer cautionsandwarnings regardingelectricalservice (AIR BAGS, ABS
BRAKES, ENGINE / BODYCOMPUTER AND BATTERY).
PLANOUT YOUR INSTALLATION anddeterminemost suitablelocationsfor all components to be placed. These components
include: themoduleitself, valet/program button, possible relays, and antenna/receiver (RS-1, RS-3 and RS-4 only, the RS-00
model does not include antennaor remotes.) Allow enoughwire to create a service loop withstrainrelief, should servicing be
required. This will also allow easier access and mounting.
DAMAGE to the CoolStart unit resulting from incorrect installation or failure to follow guidelines stated in thisbook will not be
covered under warranty and will be subject to repair or replacement charges.
USE AVOLTOHM METER to test and locate all connections. Test Lights candamage a vehicle’s computer systems.
ADDITIONALPARTS,whichare not included withthisunit, may be needed for yourparticular vehicle. These itemsmay include
extra relays or Anti-Theft System Bypass modules.

3
INSTALLATIONCAUTIONS&WARNINGS
FORSAFETYREASONS,DONOTINSTALL invehicles withMANUALTRANSMISSIONS.** Ifaccidentallyleft in
gear, aremotestarted vehiclecouldbecomeaself-propelled threat tolifeand property.
DO NOT extend the Remotestart ignition harness length. Mount the modulesothat mainharness reachesall ignition
switchwiring. Extending thesewirescouldresult inpoor or improper performance.
DONOT routeanywiring thatmaybecomeentangledwithbrake,gaspedals,steeringcolumnoranyothermovingparts
inthe vehicle.
DONOT exceed the rated outputcurrentofanycircuiton the Remotestartmodule.Failure toobservethiswarning will
result indamage tothe unit not covered under warranty.
DONOT remotestartthe vehicleinaclosed garage!Makesure thatthe garage door isopen or there isadequate
ventilation. Failure toobservethisrulecouldresult ininjuryor deathfrompoisonousCarbon Monoxide fumes.
WIRING
YELLOWWHITE:(-) HORN CHIRPHONK OUTPUT
ConnecttotheLOWCURRENTNegativeHornTriggerwireusuallylocatednearthesteeringcolumn.Ifthevehiclehorn
circuitrequires12V,then arelayisrequired.RELAYWIRING: Connectthe Yellow/Whitewire toterminal#85,connect
relayterminals#86 and #87 to12Vconstant power. Connect terminal#30 tothe 12VpositiveHorn activation wire.
BLACK:MAINSYSTEMGROUND
Connecttochassismetalofthe vehicle.Anexisting boltor screwmayprovide an adequateground,or drill asmall hole,
scrape awaypaintand attachusing asheetmetalscrew&star washer.Thiswire mustbe connectedtoaproperground
or undesirableand inconsistent operation will occur. Donot useFactoryground locations.
YELLOWBLACK:(-) IGNITIONOUTPUT-or-ANTI-GRIND/STARTERDISABLEOUTPUT
Thisnegativeoutputwire isprogrammableand can function twodifferentways.Itcan be used asaNegativeIgnition
outputfor GMAnti-theft and Transponder Bypass modules,or itcan be programmed tofunction asan Antigrind/Starter
Disableoutput. AsaNegativeIgnition wire,thiswire turnson when the remotestartbutton ispressed and stayson
through the duration ofthe remotestart. Asan Antigrind/Starter disablethiswire activateswhen the Lockbutton on the
remoteispressed and during remotestart. When using thiswire for an Antigrind/Starter disable, an optionalRelayis
neededtointerrupttheStartercircuit. Thestarterdisablecircuitaddsananti-theftfeaturetothisremotestartsystemand
preventsaccidentalgrinding of the starter if keyisturned too far after aremotestart. See diagramson NEXTPAGE.

4
WIRING
YELLOWBLACK FORNEGATIVE IGNITIONOUTPUT:(Relayand/orModulenotincluded)
YELLOW/BLACK
85 86
30 87
3rd IGN
(Ifneeded)
IGNSW.
OR ANTI-THEFT/
MODULE
+12VCONSTANT
OR
TRANSPONDER
Diodeisolate
ifusingboth!
ANTI-GRIND/STARTERDISABLEOUTPUT:(Relaynotincluded)
TO IGN 2
ENGINE ACC
START CUT
BROWN
YELLOW/BLACK 86
85
MAKECERTAINTO CONNECT"BROWN"STARTOUTPUTWIRETO
STARTERSIDEOFANTI-GRIND/STARTDISABLERELAY.
IGN 1
MAKESURE86 TERMINALHASPOWERWITHIGNITIONONANDCRANK
IGNITION
SWITCH

5
WIRING
TAN:(-) AUXOUTPUT(TRUNK POP)orDOMELIGHTILLUMINATIONOUTPUT
Thisoutput isprogrammablefor 3modesof operation. See Programming Option #9 Section.
1.30 second DomeLight output.
2.Momentary½second output (Default).
3. MomentaryPushand Hold. The output stayson until Transmitter button isreleased.
Note:SomevehicleslikeLexusand Toyotarequire a2to3second output for the TrunkPop tooperate. Thisoutput is
selectablefor Momentary½second (default)or aMomentaryPress and Holdfunction.
TAN
85 86
30 87
TrunkSoleniod
DomeLight
TRUNK OUTPUTorDOMELIGHT
OR*
(Default)
+12VCONSTANT
+12VCONSTANT
-OR-
Circuit
*Testactivation circuitinvehicle.
Connectto+12VforPositivecircuits
orGround forNegativecircuits.Relay
notincluded.

6
Momentary
Switch
NewTURBOTIMERMODE
GREEN
RS-00 EXPANSION(Default)
RS-00 OEMINTERFACE
GREEN
GREEN
(Notincluded)
(AuxChannel
AFTERMARKET
1sec.(-) pulse
FACTORYKEYLESS
Output)
ALARM/ KEYLESS
MODULE
3Consecutive
(-) pulses
WIRING
GREEN:(-) STARTACTIVATIONINPUT, OEMINTERFACEorTURBO TIMERINPUT
See descriptions&diagramsbelow.
Mode (1) [Default(-) Neg.StartActivation]Thiswire
allowsahost(or parent)alarm’sor keyless entrysystem
toactivateaRemoteStartbysending a1-Second
Negativesignaltothe Green inputwire totrigger a
remoteengine startor stop. Connect the Green wire to
the host system’sAuxiliarychanneloutput wire.
Mode(2)[AlternateOEMInterface]Thismodeallowsthe
systemtoRemoteStartor Stop when 3successive
Negativepulsesare senttothe Green inputwire.
Connectthe Green inputwire tothe Negativelocksignal
wire ofthe factorysystem.If your FactoryOEMsystem
doesnothavethistypeofsignal,thenarelayisrequired.
TURBOTIMERINPUT[3Modes,Option #22 ]Thiswire
allowsthe systemtokeep avehiclerunning for 1-5
minutes[selectively]after removing the key.Thismode
requiresthe useofamomentaryswitchthatisnot
included withthe kit. Connecta2-polemomentary
switchwithone side tochassisGround and the other
side tothe Green input wire.Ifyou ownaturbo or turbo
dieselvehicle,youcannowallowtheCoolStartsystemto
keep your engine running for 1-5 minutesafter
exiting/lockingyourvehicletocool-downwithouttheneed
for an externalTurbo Timer.
NOTE:Theturbo timerbutton will alsotriggera
remote startifitisinadvertentlypressedwhenthe
vehicleisnotrunning.Please note thiswhen
installing thebutton and choose alocation outofharm’sway.

7
WIRING
GRAY:(-) NEGATIVE HOODPINSWITCH REQUIREDFORPROGRAMMING
Connectthe Graywire toaswitchthatisatground when the hood isopen.Ifan existing switchisnotavailable,then we
recommendonetobeinstalled.Whenthiswireisgrounded,theremotestartisinhibited.Theunitwillnotattempttostart
if hood isopen. The hood pinisalsoused for Option programming.
PINK:NEGATIVE GLOWPLUG
ConnectPinkwire toindicator circuitthatshowsa(-) Signalwhilethe WAITTOSTARTLAMPison.When thiswire is
used, the systemwill wait until light turnsoff before attempting aremotestart.
PURPLE:(12V)BRAKERESET
Connectthe Purplewire tothesideofbrakepedalswitchthatshows12voltsONLYwhenpedalisdepressed.Thisisthe
wire that turnsoff the remotestart oncethe driver’skeyisinthe Ignition and turned tothe ONposition.
ORANGEBLACK:(-) OEMDISARMOUTPUT
Thiswire providesaGround pulsetodisarmthevehicles'Factoryanti-theftsystempriortoaRemoteStart. Connectthis
wire tothe vehicles' anti-theft disarmwire.Thiswire issometimesfound coming offtheDriver'sdoorkeyswitchoratthe
FactoryAnti-theft controlmodule. Thiswire maynot be needed if FactorySecurityonlyrequiresadoor unlockpulse.
ORANGE:(-) OEMREARMOUTPUT
Thiswire providesaground pulsetorearmthevehicles'FACTORYanti-theftsystemafteratimed-outorabortedremote
start. Connect thiswire tothe vehicles' anti-theft rearmwire or tothe door pincircuitdepending on your requirements.
Thiswire maybe needed topulsethe door pincircuit on vehicleswithretained accessorypower.
WHITE:12Vor(-) NEGATIVE PARKING LIGHTOUTPUT:
Connecttovehicleparking light circuit at the backof light switchor if thisisnot possible, connect directlytoone of the
parkinglightsatthefrontofthevehicle.Ifyourvehiclehasamultiplexlightingsystemthatrequiresa(-)Negativeparking
lightoutput, then open the access door on the top ofthe moduleand movethe jumper.See Jumper Pinsection.Some
European vehiclesrequire separateleft and rightcircuits.Useadualrelayor diodestoisolatethe output. Notethe
current limit on the Negativeparking light output. You mayrequire an externalrelaytoprevent damage tothe unit.
(1)Defaultparking lightoutputis12 volts.
(2)Use anexternalrelay forvehicles that drawexcess currentfromextrarunning lights,lightbars,ortrailers.
Parking lightoutputislimitedto(+)10 ampsor(-)500 mAonly.

8
REDWHITE:TACHOMETERINPUT
When installing the systeminTachmode,thiswire mustbe connected toavalidsourceofACvoltage.Thiswire allows
the unit tosensethe engine running and controlthe starter motor.
PROGRAMOVERRIDESWITCH:2PINPLUG (REQUIREDFORPROGRAMMING &LEARNING REMOTES)
Thisswitchisused for programming features,transmitters,valetmode,and tooverride the optionalstarter disable(if
installed) inthe event of anon-operating remotecontrol.
LED:2PINPLUG OPTIONAL
The LEDisused asaVALET/PROGRAMMING indicator and it will alsoFLASHfor useassecuritydeterrentwhen the
optionalANTI-GRIND/STARTERDISABLEoutput isprogrammed.
VALET/ PROGRAMSWITCH
STATUS LED
WIRING:6-PINHIGH-CURRENT CONNECTOR
BROWN:12VSTARTEROUTPUT30A:
Connect tocircuit inthe vehiclethat haspower ONLYwhilethe STARTERMOTORisCRANKING.
GRAY:12VACCESSORYOUTPUT30A:
Connecttocircuitinthe vehiclethatprovidesAccessoryPower for systemssuchasHEATand A/C.Typically,thiswire
turnsONwiththe firstposition ofthe key,DROPS OUTWHENCRANKING, then returnsasthe engine startsand runs.
(2) RED:12VPOWERINPUTWIRES (30AFused):
Connect tobothofthese leadsto12VConstantPower. Werecommend theBATTERYPOSITIVE TERMINAL.
PINK:12VIGNITIONOUTPUT30A:
ConnecttocircuitinthevehiclethatprovidestrueIgnitionPowerforsystemssuchasSparkandFuel.Typically,thiswire
turnsONwiththe second position of the key, STAYSONWHENCRANKING, and continuesONasthe vehicleruns.
PINK WHITE:12VMULTIFUNCTIONOUTPUT30A(JUMPERSELECTABLE):
Thisisan optionalmulti-function outputwire the can be configured asaSecond IGN,ACC or STARTERoutput. Some
vehiclesrequire more than justone IGN,ACC,or STARTERwire inordertostartandrunsuccessfully.Ifthisisthecase
for your particular vehicle,then usethe jumper pinlocated under the access panelon the top ofthe CoolStartcontrol
moduletoconfigurethiswiretosuityourneeds.TheDEFAULTsettingisIGNITION.SeeJumperPinDiagrampage24.

9
CrimestopperDoorLock Accessories:
CS-6600DLM: Dual-relayplug-inmoduleforReverse
Polarity, Positive, orAftermarket Motors.
CS-6500DLI: Plug-inpulseinverterthat convertsthe
Negativeoutputsof the systemtoPositivetype forPositive
DoorLock systems.
CS-610S1: Aftermarket doorlock actuator(motor).
POWERDOORLOCK WIRINGCONNECTOR
BLUE: (-) Negativepulsefor UNLOCK
RED: 12VWhen using externalrelays(TERM86)
GREEN: (-) Negativepulsefor LOCK
DETERMININGDOORLOCK TYPE: Werecommend
determining the type of locking systemthe vehiclehasbefore
connecting anywires.Incorrectconnection mayresultin
damage tothe alarmand/or vehiclelocking system.Doorlock
information isprovided asaguide. Your vehiclemaydiffer.
NegativeTrigger(-):ManyImports;Late model Ford&General Motors
Negativetrigger door locksystemssend aNegative(Ground) pulsetoexisting factoryrelaystolockand unlockthe
vehicledoors.
PositiveTrigger(+):ManyGeneral Motors;Chrysler/ Dodge/ Plymouth
Positivetrigger door locksystemssend aPositive(12V)pulsetoexisting factoryrelaystolockand unlockthe vehicle
doors.
Reverse Polarity:ManyFord/Lincoln/Mercury/Dodge/Chrysler/Plymouthand early90’sGMTrucks
ReversePolaritysystemsuseno relays, but instead the door lock/unlockmotorsare controlled directlyfromthe lock
and unlockswitchesinthe door. The lockand unlockwiresrest at NegativeGround when not inuse. When the lock
or unlockbutton ispressed, one of the circuitsis“Lifted” and replaced with+12Vcausing alockor unlocktooccur.
SingleWire(Dual Voltage):Late model Chrysler/Dodge/PlymouthVehicles, some2000-UPGM
DualVoltage systemshavelock/unlockswitchesthat send varying levelsof Positivevoltage ORNegativeground
current tothe SAMEwire for bothlockand unlock. When the vehicle’sBodyComputer Module(BCM)or door lock
modulesensesdifferent voltageson thiswire, the systemwill either lockor unlock. Singlewire door locksystems
require relaysand resistors.
DatabusSystems2003-UPGMTrucks &SUV’s, ‘96-04 JeepGrand Cherokee
Databussystemssend lowcurrent“Datamessages”tothe door lockcontrollerson anetworkinordertolockandunlock
the vehicle.Toinstall aftermarket systemsinthesevehicles, an interfacemoduleisrequired that convertsthe regular
lock/unlockpulsesinto“Datamessages”toallowlocking &unlocking. Interfacemodulesare soldseparately.

10
BASICDOORLOCK DIAGRAMS
AFTERMARKETMOTOR/DOORLOCKWIRING
REVERSE POLARITYDOORLOCKWIRING
GREEN
GREEN FUSED
FUSED RED
RED +12V
+12V BLUE
BLUE +
+
86858685
8685
8685 8787
8787 3087A3087A
3087A3087A
+L
CUT
UL
CUT
MASTER
SWITCH
NEGATIVETRIGGERDOORLOCK WIRING POSITIVE TRIGGERDOORLOCK WIRING
GREEN
GREEN FUSED
RED +12VRED BLUE +
BLUE
86
858685 8787 3087A30
87A
FACTORY
FACTORY
LL
POWER
POWER LOCKING
LOCKING
UL UL
RELAYS RELAYS

11
“SMART TACHLESS”MODE
Your CoolStart systemincludesaunique voltage monitor called “SmartTachless”mode.Thismode allowsthisunitto
efficientlystart an engine withoutthe useofatachsignalwire.Thesemodulesactivelymonitor the voltage levelofthe
vehicletocontrolthe starter motor eachtimearemotestart isrequested.
IMPORTANTNOTES:
(1)SETUPmaybe required for the CoolStart“SmartTachless”Mode.Ifyour vehiclehasnotbeen atrestfor aperiod of
time(Hotengine),thenyoumustdrainthesurfacechargefromthebattery.Unplugmainpowerharnessfromunit,turn
HEADLIGHTSONfor 4minutestodrainoff excess surfacecharge on vehicle’sbatterythen reconnect.
(2)Onthe rare occasion that“SmartTachless”mode doesnotoperatesatisfactorily,change the voltage referencelevel
asdescribed below, or useadifferent mode suchas“Tach” mode, or “Timed Crank”mode.
“SMARTTACHLESS”ADJUSTMENT:
Inthe event“SmartTachless”over-cranksor under-cranksyour starter,the settingscan be changed.The purposeof
adjusting the “SmartTachless”Mode istoraiseor lower the voltage referencethresholdfromthe 93%defaultpoint.
Raisingorloweringthis93%pointshouldincreaseordecreaseyourcrankingtimerespectively.Theadjustmentrangeis
from79%to100%inone percent increments. Followstepsbelowtoadjust the referencelevel.
1.Open hood (or ground Grayhood pinwire if no hood pinisinstalled)
2.Turn the keytothe ONposition (Pinkwire must be connected!)
3.Press programbutton 5times, after afewsecondsthe unit will flashthe lightsand/or honkhorn 5times.
4.Carefullypress the programbutton 21timestogettooptionlevel21.Youmustgetalightflashand/orhornhonkafter
eachpress. If the lightsdidn’tflashand/or horn doesnothonk,then the unitdidnotregister your button press.Only
count the light flashand/or horn honk.
5.PresstheLockButton#1ontheremotetodecreaseby1%(lightswillflashand/orhornhonk1Xforeachpress);Press
the UnlockButton #2 toincreaseby1%(lightswill flashand/or honkhorn 2Xfor eachpress);Press the TrunkButton
#3 toresetto93%(lightswill flash3X).The unitwill stop providing lightflasheswhen you reachthe bottom(79%)or
the top (100%)ofthe adjustmentrange.Ifyou losttrack,then justpress Button #3 toresetbackto93%and begin
raising or lower again.
6.Turn Ignition OFF, Closehood (or un-ground the Grayhood pinwire) and checkoperation.
NOTE:ThisSmartTachless adjustmentfeatureisnotavailableon theRS-00 Modelthat has no remote
transmittersorantenna.Ifyou must use thisfeatureon aRS-00,thenaremote and anantennamodulefroman
RS-3 orRS-4 must beusedtoset thedesiredlevel. Once programmed, remove antenna.

12
TACH FINDER&USEFUL TIPS
TACH FINDERMODE:
ThisTachFinder mode can assistinlocating aTachsourcefor your installation.When following the steps,the unitwill
begintoflashthe parking lightsifyou havethe Red/Whitewire connected toatachsource.Iflightsdo notflash,then try
another wire until you locateatachsignalthatwill causethe Parking lightstoflash.NOTE:Onsomevehiclesequipped
withdaytimerunning lights,itmaybe difficulttosee anyflashing parking lights.Inthiscaseyour onlynotification will be
the slight “ticking” sound coming fromthe module’sflashing light relay.
TACH FINDERSTEPS:
1.Open hood (or ground Grayhood pinwire if no hood pinisinstalled)
2.Start Engine withthe key. (Pinkwire must be connected!)
3.Press the Programbutton for 2seconds
4.Lightswill beginflashing if the Red/Whitewire isconnected toavalidtachsource. If not tryadifferent tachwire.
5.OnceTachislocated then turn off engine and closehood toabort (RemoveGrayhood pinwire fromground).
6.Nowfollowthe TachProgramming steps.
TACH FINDERTIP:ColdWeather/ High IdleSimulation:
The tachfinder mode can alsobe used tohelpdetermine howyour CoolStart systemmayoperateinacoldweather
situation. Onceyou haveavalidtachsourceprogrammed intoyour system, followtest stepsbelow.
1.Gointothe tachfinder mode.
2.You shouldhaveaconsistent light flash(likedirectionalor emergencyflashers).
3.Slowlyraisethe RPMlevelon your vehicletosimulatea“warm-up idle” that ishigher than the normalidlelevel.
If and when the lightsSTOPflashing. Meansthat thisisthe point at whichthe tachsignalisout of range of the
system.
4.Werecommend that you bring the RPMlevelup tobetween 1000 and 1500 RPMstosimulateacoldmorning
idle.
5.If the lightsstop flashing too quickly, then werecommend using another tachsource. Thismayhelpprevent
the engine fromstarting and stalling inthe morning or coldweather.

13
TACH PROGRAMMING&TACH SIGNALS
INTRODUCTION
Tachsignalswillvaryinlevelsandfrequenciesdependingonmanyfactorsincludingthetypeofvehicleandthesourceof
the signal.The signalsfromavehicle’sinjector wire and coil packwire can varygreatlyeven on the sameengine.The
tachsignalfroman engine can alsobe affected byother sourcessuchaselectronicnoisefromthe ignition or computer
modules.RecentimprovementshavebeenmadetothecircuitrytoallowthisCoolStartsystemtosenseawiderrangeof
tachsignalsthan previousmodels.
TACH MODE
The Tachmode providesreliableremotestarting performancethrough engine speed(RPM)sensing.WhenusingTach
ReferenceMode,the Red/Whitewire isused for Tachsignal[Engine RPM]input. Mostmodernenginesincludevarious
pointswheretheEngineSpeed[Tach]orA/Csignalmaybeobtained.TachSignalexamples:Negative(-)sideofignition
coil,atthe Distributor or Ignition ControlModule,Coil Pack,Engine Computer,or Crankshaft Sensor.SometimesFuel
injectors,and Alternator stator pinscan be used.TheseTachSignallocationsmentioned are provided asaguide.Your
vehiclemaydiffer. Somelocationswill NOTbe agood location for Tachsourcedue toRFnoiseor Computer Data.
TACH PROGRAMMING:
1.Open hood (or ground Grayhood pinwire if no hood pinisinstalled.)
2.Red Whitewire shouldbe connected toavalidTachsource.
3.Start engine withkey. (Pinkwire must be connected!)
4.Press programbutton 5times, then wait for 5light flashesand/or 5horn honks.
5.Pushprogrambutton oncemore. (You must get one light flashand/or honkafter button ispressed.)Thisunit is
nowat option #1-TachLearning.
6.Press the #1 LockButton on remotetransmitter. The unit will read the Tachsourceand flashthe lightsand or
honkoncefor programconfirmation. (OnRS1300DPII modelswithout remotetransmitters, press the brakepedal
inthisstep.)
7.If lightsdo not flashfor confirmation, then tryanother tachsourceor trythe tachfinder tolocateanother wire
EXAMINING THE TACH FREQUENCYWITH ADIGITAL MULTI-METER
If youownaDigitalMulti-Meter meter withafrequency counter setting, itcanbe helpfulto measureandresearchtherange oftach
signalfrom yourparticular engine. Whenprobingyourchosentachwire, observe thefrequencyreadingfrom themeterat boththe
warm/low engineidleandcold/high engineidlepoints. Tachsignalsrangingbetween70Hzand700Hzare desired. If yourtach
wire has readings that are not inthisrange, theunitmay not operate properly. Thefrequency of thetachwire inthisrange does
not guarantee operation.If youcannot locate agood tachsource from yourengine, thenyoucanswitchyourCoolStartsystemto
the “Smart Tachless” or “Timed Crank”.

14
TIMEDCRANK MODE
Thisfeatureprovidesaneasymethodofstartingthevehiclewithoutlocatinganexacttachwire.Thesystemusesatimed
cranking outputcombined withthe useofthe Red/Whitetachwire asan engine ON/OFF monitor.The Red/WhiteTach
wire muststill be used inthismode ofoperation.THISFEATUREMUSTBE PROGRAMMEDBEFOREUSE!THERE
ARE2LEVELSofprogrammingrequired:First,setthesystemfor“TimedCrank”operation,andsecondlyyoumayneed
toadjustthe amountofcranking time.There are 4differentcranktimesavailablefor use.SEE OPTION
PROGRAMMING CHARTONPAGE16-17 FORSETTINGS.
HOWTO USE THISFEATURE:
1.Gotothe “ProgrammableOptions”section ofthismanual,and turn “ON”Option #15 "TimedCrank".(Itisnormallyon
TachMonitor)
2.With“Timed Crank”turned ON,you will STILL havetoconnectthe Red WhiteTachwire toatachsourceon the
engine. The Red/WhiteTachwire becomesasimple“Engine Monitor”. Although the unit will not be using the Red
Whitewire tostartthe motor,itwill be using thiswire todetermine whether the motor isrunning or not. Thisisa
mandatoryconnection. A“crude” or “less exact”tachsourcecan be used onlywhen in“TimeCrank”mode.
3.Using the vehiclekey, start the engine afewtimestogeta“feel”ofhowlong the cranking timeis.Oncethe “Timed
Crank”modeisturnedon,thedefaultcrankingtimeissettoadefaultof0.50seconds.Werecommendbeginningwith
thissetting. Tryaremotestart and see if the cranking isappropriatefor your vehicle
4.If0.50 secondsisnotan appropriatestarter cranking time,thengotoProgrammingOption#18andchangethecrank
timesetting toalonger value. The valuesare asfollows: 0.5, 0.75, 1.0, and 1.5seconds.
WARNING:Thismethod ofstarting thevehicleisnotas reliableas using regular“Tach”orSmartTachless
modes.Thismethod shouldbeusedonlyintheeventthat atachwirecannotbelocatedusing thenormaltach
programming and tachfinder.Whenusing thismethod,theremaybecertainoperating anomalies requiring
seasonal adjustments. These are, butnotlimitedto:
•Starter mayunder-crankinextremecoldweather.Vehiclemaynotstarton 1st attemptand mayrequire a2nd or 3rd try.
•Inwarmweather when your vehiclemaystart veryquickly, “Timed Crank”mode maytend toover-crankthe starter.
•The onlywaystocorrect the aboveissuesare togo toOption #18 and adjust the cranking time.
•Whenin“TimedCrank”mode,thecrankingtimecanonlybeadjustedmanuallythroughoption#18.Whenthesystem
isinTachor Smart Tachless modesthe cranking timeiscontrolled automaticallybythe microprocessor.

15
DIESEL GLOW PLUGDELAY
Thisfeature providesasolution for dieselvehicleswithouthaving toconnecttothe GlowPlug-WaittoStartCircuit. This
maybeneededforvariousreasons.IfyourvehicledoesnothaveaviableWaittoStartCircuit,oryoucannotlocateand
identifythe circuit, then change your systemtoDieselGlowPlug Delaymode.You can choosefromaselection ofpre-
cranking delaytimes.Oncethismode isactivated,the systemwill NOLONGERmonitor the PINKglowplug inputwire
and will useadelaysetting chosen bythe installer inthe option chart.
NOTES:Thisfeature isOFF bydefaultand mustbe programmed before use.Oncethisfeature isturned ON,the Pink
Glowplug inputwire isnotused.The Remotestartunitwill alwayswaitthe programmed timebefore cranking EVENIF
the glowplug warmsup first. There are 3differentDelaytimesavailablefor use:10,20,or 30 seconds.SEE OPTION
PROGRAMMING CHARTon Pages16-17.
HOWTO USE THISFEATURE:
1.See the Option Programming section on Pages17-18 and change Option #19 fromMonitor GlowPlug Light toone
of the delayed timevalues. (Default setting istoalwaysmonitor the PINKGlowPlug input wire.)
2.Oncethisoption haschanged, the systemwill wait for the selected timebefore cranking.
OPTIONPROGRAMMING
ThisCoolStartunithasover23programmablecontroloptionstocustomizethesystemforvariousoperatingfeaturesand
installer preferences.Examinethechartonthepages16-17alongwithreadingthedescriptionsthatfollowonpages18-
20.You maychange one option atatime,or programmultipleoptionsinone session.Ifyou startwiththe lowestoption
and continue on tohigher options,you donotneedtorepeatsteps#1-3eachtime.Forexample,youcanchangeOption
#2 to“ON”, then you can continue pressing the programbutton toget toahigher number option and change itaswell.
You can onlygo fromlowtohigher optionsnumbersinone session.
OPTIONPROGRAMMING CHARTBEGINSONNEXTPAGE

16
OPTIONPROGRAMMING
To EngageOption Programming:
1. Open hood,Ifno hood pinswitchisinstalled,then ground the Grayhoodpinwire.TurnKeytotheONposition.Donot
start vehicle(Pinkwire must be connected!)
2.Press the programValet button 5times. Wait for the unit toflashthe lightsand/or horn honk5times.
3.Pushthe valet programbutton the number of timesthat correspondstothe option number desired (1-23X). You
must get alight flashand/or honkafter eachbutton press. If the systemdidnot flashthe lightsand/or honk, then it
didnot register your press. Press carefullyand do not losecount.
4.When you reachthe desired option #, Press button #1 Lockor #2 Unlocktochange the option. (Someoption
numbersuseALL 4remotebuttonstoselect settings). You can alsotap the brakepedaltotogglethrough the
option values: Tap brakeonce(lightsflash1X)Tap the brakepedalagain(Lightsflash2X)tap 3or 4timesfor
optionsthat have3or 4values.
5.When finished, turn Ignition OFF, closehood (or un-ground Grayhood pinwire) and checkfor changed features.
OPTIONPROGRAMMINGTABLE
Option
#Option Description TXButton #1 TXButton #2 DefaultValue TXButton #3 TXButton #4
1 EngineMonitoring LearnTach *Tachless*
2 Autolock withRPM/Ignition ON *OFF*
3 DoorLock Pulse Time 3 Sec. *0.50 Sec.*
4 DoubleUnlock Pulse 2 Pulses *1Pulse*
5 DataPortProtocol OFAorSLSeries OFASeries *SLSeries*
6 RemoteStart&AuxiliaryOutput
ButtonPress Selection DoubleButton Press *½SecondPress* Press and Hold
7 HornChirpsonRemoteStart ON *OFF*
8 Lock AfterRemoteStart/Abort OFF *ON*

17
Option
#Option Description TXButton #1 TXButton #2 DefaultValue TXButton #3 TXButton #4
9 Brownwirefunction DomeLight *Trunkpop* Press and
Hold
10 “Wake Up"pulse onUnlock
(1-sec. +12VtoIGN) ON *OFF*
11 Manual TransmissionMode ON *OFF*
12 Yellow/black wirefunction Anti-Grind *IgnitionOutput*
13 HornChirpConfirmation 1Press *2Press*
14 Unlock withTrunkPop Unlock/Trunkpop
*Trunkpop only*
15 TimedCrankorTachMonitor Pre-Set *TachMonitor*
16 HornPulse (Chirp) Long0.04 Sec. *Short0.02
Seconds*
17 OEMInterface Greeninputwire
(RS-1300DP) 3pulse *1Pulse*
18 StarterCrankingTime
(Option#15 issettoTimedCrank) 0.75 Sec. *0.5Sec.* 1.0Sec. 1.5Sec.
19 Diesel Glow PlugDelay 10 Seconds *MonitorGlow
Plug 20 Seconds 30 Seconds
20 RemoteStartEngineRun Time 12 Minutes *24 Minutes* 36 Minutes 48 Minutes
21 SmartTachless VoltageAdjustment
79-100%-1% +1% Setto93% default
22 Turbo TimerMode1to5Minutes Brake Pedal Set
Mode *AlwaysSetMode* IdleDown Mode
23 ResetOptionstodefault(*) *ResetAll Options*
OPTIONDESCRIPTIONS:
1. EngineMonitoring:
Thisoption setshowthe unitmonitorsyour engine.YoucanprogrameitherforTachmodeinwhichtheunitusesaTach
signal(RPM)or for Tachless mode thatmonitorsvoltage level.See pages12-15 for more information and additional
stepsfor actualTachlearning and Tachfinder modes.

18
OPTIONDESCRIPTIONS
2. AutoLock Unlock:
The option controlswhether the doorswill automaticallylock/unlockon your vehiclewhen driving or withturning the
Ignition ON/OFF. If the AutoLockfeature isturned on,and the systemisinTachmode,then the doorswill lockasthe
engine RPM’sincrease(driving).Ifthe AutoLockfeature isturned on,and the systemisinSmartTachless mode,then
the doorswill lockwhen the Ignition isturned on. When the AutoLockfeature isturned on, the systemwill unlockthe
doorswhen the Ignition isturned off. Withthisfeature OFF,the systemwill notautomaticallylockor unlockthe vehicle.
3. DoorLock Pulse Time:
Controlsthe amountoftimefor lock/unlockpulse.The standard setting is0.5for mostvehicles.A3sec.setting is
required for 1980’s/90’sEuropean Vacuumor Pneumaticdoor locksystems.
4. DoubleUnlock Pulse:
Theunitwillsend2unlockpulseswhenthe#2Unlockbuttonispressed.Thisfeaturemayberequiredforinterfacingthis
alarmwithan existing FactoryKeyless Entryor Alarmsysteminavehicle.Thesesystemsare found on someChrysler,
Nissan, VW, Toyota, and Lexusvehicles.
5. Data PortProtocol:
ThisoptioncontrolstheDataPortProtocolforOFASeriesmodulesorSLSeriesmodules.ThedefaultissetforSLSeries
Protocol.Thisoption hasno effectonconventionalwiringofBypassmodules.BothOFAseriesandSLseriesarenow2-
WayProtocol.
6. Remote Start&AuxiliaryOutput–Button Press Selection:
Toeliminatethe possibilityofaccidentallyopening the trunkor starting the vehicle,there are (3) optionsfor button press
selection. Thisoption will allowyou tochange whether the Remotestarter and Trunkreleaseactivatebya:
4.Doublebutton -½second presses.
5.Single½second press.
6.Press and Hold2seconds.
7. HornChirpson Remote Start:
Thisoptionallows theunitto provide 3short chirps for audibleconfirmationof aremote start. Thehornoutputwire must be
connected for this feature.
8. Lock During AfterRemote Start:
This optioncontrols whether the unit will automatically lock during and after a remote Start abort or time-out.

19
OPTIONDESCRIPTIONS
9. BrownOutputWireFunction:TrunkPop orDomeLightOutput
This optioncontrols how the Brownoutput wire of the unit functions, either for Trunk pop or for Dome light illumination.
10. 12V“Wake up”Pulse:
Thisoptionallows theunitto provide a1-secondpulse onthePinkmainignitionoutputwhenunlocking. TheIgnitionpulseserves
to “Wake up” vehiclecontrolmodules or body computers that “time out” or go into power savingmode. Thisisrequired onmany
late modelFord vehicles with a“Slam” lock system in order to actuallyunlock thevehicleafter ithas beenshutdownfor ashort
period of time.
11. Manual Transmission Mode:AuthorizedCrimestopperDealersOnly. Call TechSupportforInstructions.
12. Yellow Black WireFunction:(-) NegativeIGNorANTI-GRIND / StarterKill Output
Thisoptioncontrolstheunits Negative multi-functionoutput. Default: Negative IGN outputthat turnsON andstays onfor the
durationof theremote start. Use thiswire to turnonAnti-theft bypass adapters for GM or Transpondersystems. Whenchangedto
anAnti-Grind, thisoutputactivates whentheLock buttonontheremote ispressed andactivates duringaremotestart. Anti-Grind
is designed for use withanoptionalStarter disable relay (Not included).
13. HornChirpwithLock and Unlock- 1or2Button Press (WhenOptional HornOutputinstalled):
Thisoptionallows thesystem to chirp thevehiclehornfor Lock/Unlock confirmationon1buttonpress or a2nd press within3
seconds. The hornoutput must be connected to use this feature.
14. Unlock WithTrunkPop orTrunkPop Only:
Thisoptioncontrolswhether thesystem will provide anUnlock/Disarm pulse whentheTrunkrelease isactivatedfrom theremote
control. This may be required to prevent unnecessary triggering of a factory alarm onsome vehicles.
15. TimedCrankModeorTachMonitor:
This optioncontrols whether the system uses a tachwire to controlthe starter or uses a pre-set starter cranking time.
16. AdjustableHornPulse:
Some vehicles require anextended hornpulse to activate theFactory horn.Use thisoption#16 to EXTEND thehornpulse
slightly.

20
OPTIONDESCRIPTIONS
17 OEMInterface (RS-00 Add on Model):
ThisoptioncontrolstheinputselectionfortheGreenNegativeStartTriggerWire.WhenusinganAftermarketHostAlarm
or Keyless EntrySystem:Leavethe setting as“1 pulse” and connectthe Green wire tothe (-) Auxiliaryoutputwire ofthe
Alarmor Keyless EntrySystem.For FactoryKeyless entrysystems(withouta(-) Negativeauxiliaryoutput),change the
option to“3 Pulse” and tap the green wire intoaNegativesignalwire on the vehiclesuchasaNegativedoor lockwire.
Pressing the Factoryremotelockbutton 3timeswill produce3short negativesignalstotrigger aremotestart.
18. Pre-Set StarterCranking Time:(Requires Option #15 tobeset toTimedCrank)
Thisoption controlsthe starter output cranking time. Choicesare 0.5, 0.75, 1, or 1.5seconds.
19. Diesel Glow Plug Delay:
Thisoptioncontrolsthesystem’sDieselvehicleinterface.Usingthisoptionyoucancontrolwhethertheunitmonitorsthe
vehicle’sglowplugcircuitusingthePinkinputwire(Default),oryoumayselectaspecificdelaytimebeforecranking.This
option ishelpfulifyou are unabletolocateaglowplug signal.Justselectadelaytimeand do notconnectthe PinkGlow
Plug wire. Selections: 10, 20, 30 seconds, or Monitor PinkWire (Default).
20. Remote StartRun Time:
Thisoption controlsthe engine run timefor remotestart. Usethe buttonson the remotecontroltosetachoiceof12,24,
36, or 48 minutes. The default setting is24 minutes.
21. SmartTachless VoltageAdjustment:
Thisoption controlsthe voltage referencepointwhen using smartTachless mode.Pressing the Lockor Unlockbuttons
on the remoteraisesor lowersthe referencelevelin1%incrementsfrom79%-100%. Button #3 resetsthe unit tothe
factorydefaultreferencepointof93%.The default93%setting worksfor mostvehicles.See page 12 for additional
Smart Tachless mode information.
22. Turbo TimerMode:
The optionalTurbo Timer mode allowsthe CoolStartsystemtokeep aTurbo or Turbo Dieselvehiclerunning for 1to5
minutes[selectively]afteryouremovethekeyandexitthevehicle.Thisishandyforturbocool-downwithouttheneedfor
expensiveturbotimers.Thismoderequirestheuseofanextrapartcalledamomentaryswitch/buttonthatisnotincluded
withthe kit. There are (3) modesof operation for the Turbo Timer Mode. See ownersmanual.
23. Option Reset:(RESTORETO DEFAULT)
Thisoption restoresall programmableoptionstofactorydefault. Gotothe option 23 and press the UnlockButton #2 on
the remote. The unit will flashthe lights2timesand all valueswill be reset tofactoryoriginalsettings.