Crosley Furniture CO600142-BK User manual

CO600142-BK
42”CAST ALUM. DINING TABLE

HARDWARE LIST
6
78
9
PARTS LIST
Cylinder Bolt
(M8*25)
4 PCS
Leg
4 PCS
Top
1 PC
Stretcher
1 PC
Bolt
(M6*30)
8 PCS
Flat washer
(M6)
8 PCS
Bolt cap
(M6)
8 PCS
Wrench
(M6)
1 PC
(M8) (M8) (M8) (M8)
4444
PCS PCS PCS PCS

3 of 4
STEP 1
Figure 1
Place Top (A)
upside down on a soft cloth.
Insert all Cylinder Bolts (Part #1) into
.
B
B
B
B
C
A
Nut Cap
(M8)
(M8)
(M8)
(M8)
Nut
Spring Washer
Flat Washer
(M6)
Flat Washer
Bolt(M8*25)
Bolt
(M6*30)
Bolt Cap
(M6)
Figure 2
Flathead screw
driver(not included)
Figure 2
8
6
7
5
4
2
3
1
Step 1:
Step 2: Attach two adjacent Legs (B)
to Top (A) by inserting the Cylinder
Bolts (Part #1)
the ends of the Legs (B). Now secure
through the holes in
the Legs (B) using Flat Washers
(Part #3),Spring Washers (Part #2)
& Nuts (Part #4).
Note - -Tighten Nuts only half way
using wrench (#9) .
Step 3: Attach Stretcher (C) to
attached Legs (B) using Flat Washers
(Part #7),and Bolts (Part #6) as shown.
Note - Tighten Nuts only half way with
wrench (#9).Now attach the other two
Legs (B) to Top (A) & Stretcher (C)
using the same method as the first
two legs.Tighten all bolts completely
with wrench (#9).
Step 4: Cover all Nuts and bolts with
Nut Caps (Part #5) & Bolt Caps (Part
#8).Turn the table over into the upright
position.
Congratulations! You are finished.
f Tthe pre-drilled holes o op (A).

CAST ALUMINUM
HIGHBACK ARM CHAIR
CO6102-BK

910
Spring Washers
(M8)10PCS
Spring Washers
(M6)4PCS
(M6*25)
Short phillips Heat Bolt
(M6*30)
Wrench
(M6 & M8)
1 PC
11
Flat Washer(M6) Flat Washer(M8)
PARTS LIST
Seat
1 PC
Back
1 PC
Left Arm
1 PC
Leg
1 PC
Right Arm
1 PC
Long phillips Heat Bolt

Step:2 Attach Back (B) to Seat(A) with Flat Washers(Part #2),Spring Washers(Part #10)
& Nuts(Part #4).Note - Do not tighten Nuts(Part #4) completely at this time.
3 of 5
Step:1 Place seat (A) upside down on a soft cloth. Seat (A) with,
Attach Legs (C) to
Flat washers(Part #2), Spring washers(Part #10),and Nuts(Part #4).Note -
Do not tighten Nuts(Part #4) Completely at this time.
C
A
B
Washer (M8)
Nut (M8)
Nut Cap (M8)
4
8
10
Flat
2
Spring Washer (M8)
Washer (M8)
Nut (M8)
Nut Cap (M8)
4
10
Flat
2
8
Spring Washer (M8)

Step:4 Congratulation!
You are finised
Step:3 Attach Arms (E&D) with Short Phillips Head Bolts(Part #5),
Long Phillips Head Bolts(Part #6),Flat Washers(Part #1),
Spring Washers(Part #9) & Nuts(Part #3).Completely
tighten all Nuts(Part #’s 3 & 4) and cover with Nut Caps
(Part #’s 7 & 8).
4 of 5
Spring Washer (M6)
Flat Washer (M6)
Nut (M6)
Nut Cap (M6)
1
3
9
7
Short Phillips Head Bolts (M6)
5
Long Phillips Head bolts (M6)
6
Nut Cap (M6)
7
Nut (M6)
3
Spring Washer (M6)
9
Flat Washer (M6)
1
D
E