CTC Union FMC-1000-PH User manual

CTC Union Technologies Co., Ltd.
Far Eastern Vienna Technology Center
(Neihu Technology Park)
8F, No. 60, Zhouzi St., Neihu District, Taipei 114
Taiwan
T+886-2-26591021
F+886-2-26590237
E[email protected]
© 2015 CTC Union Technologies Co., Ltd.
All trademarks are the property of their respective owners.
Technical information in this document is subject to change without notice.
Introduction
FMC-1000-PH & FMS-1000S-PH are unmanaged Gigabit PoE
(Power over Ethernet) converters that provide stable and reliable
Fast and Gigabit Ethernet transmission. PoE technology describes
a system to pass electrical power safely, along with data, on
Ethernet cabling. The original IEEE 802.3af-2003 PoE standard
provides up to 15.4W of power to the connected device. The
updated IEEE 802.3at-2009 PoE standard also known as PoE+ or
PoE plus, provides up to 30W of power. FMC-1000S-PH gives you
the freedom to extend your 10/100/1000Mbps cabling distance
by allowing connectivity up to 120KM over fiber. LED indicators
signal the power status, UTP link & speed, fiber link & speed and
PoE status.
Features
Conversion between 10/100/1000Base-T and 1000Base-X or
100/1000Base-X SFP Fiber cable interface
Support IEEE802.3at/af PoE
Support LFPT (Link Fault Pass Through)
Support DIP Switch setting
Support jumbo frame 9K bytes packet
Support wall-mounting installation
Compact size for easy installation
Specifications
Ethernet Interface
Standards: IEEE802.3 (10Base-T), 802.3u (100Base-TX), 802.3ab
(1000Base-T)
Interface: 1 x RJ-45 (shielded) connector
Speed: 10/100/1000M (Auto)
Optical Interface
Standards: IEEE802.3u (100Base-FX), 802.3z (1000Base-X)
Interface: 1 x fixed fiber (FMC-1000-PH) or 1 x SFP slot (FMC-
1000S-PH)
Speed: 1000M (FMC-1000-PH) or 100/1000M (FMC-1000S-PH)
Quick Installation Guide
FMC-1000-PH
FMC-1000S-PH
10/100/1000Base-T to 1000Base-FX or 100/1000Base-X SFP
with PoE+ (PSE) Fiber Converter
Specifications (Cont.)
Switch Features
Store & Forward Switch mode or Pass Through Converter mode
Packet Size: 9K bytes
Supports IEEE802.3x Flow Control
Auto MDI/MDI-X
Duplex: Full/Half
Power over Ethernet
1 PoE enabled port, End-span, Alternate A Mode
Supports IEEE802.3af 15.4watts PoE per port
Supports IEEE802.3at 30watts PoE+ per port
Positive (VCC+) pins 1,2; Negative (VCC-) pins 3,6
Data: 1, 2, 3, 6, 4, 5, 7, 8
Power
DC Input Power: 48~57VDC
Reverse Polarity Protection: Yes
PoE Power Budget: 30W
Consumption:
Model
Power
FMC-1000-PH
FMC-1000S-PH
Input Power Consumption
32.3W
31.7W
PoE Power Budget (W)
30W
30W
Mechanical
Dimensions: 108 mm (D) x 74 mm (W) x 23 mm (H)
Mounting: Wall mounting (optional)
Weight: 90g (FMC-1000-PH), 80g (FMC-1000S-PH)
Environmental
Operating Temperature: 0°C~50°C
Storage Temperature: -40°C~85°C
Humidity: 10%~90% (Non-condensing)
MTBF (MIL-HDBK-217)
FMC-1000-PH: 774,378 Hours
FMC-1000S-PH: 749,556 Hours
Certifications
EMC: FCC Class A, CE
V1.0
- 2 -
- 1 -
[email protected]
www.ctcu.com

Panels
FMC-1000-PH
FMC-1000S-PH
No.
Description
1
LAN connection
2
Fixed Fiber interface
3
SFP Fiber slot
4
LED indicators
5
DIP Switch
6
Power input
Table 1: Index Reference
DIP Switch Function Descriptions
Pole No.
Status
Setting
Function Description
1
OFF *
Disable
Disable link fault pass
through.
ON
LFPT
Enable link fault pass
through.
2
OFF *
Switch
Store & Forward
Switching mode.
ON
Pass
Thru
Pass through converter
mode.
3
OFF *
FX Auto
Fiber duplex auto mode.
ON
Force
Fiber force mode.
4
For FMC-1000S-
PH Only
OFF *
1000
Force Fiber speed to
1000Mbps.
ON
100
Force Fiber speed to
100Mbps.
NOTE 1: By default, all DIP switches are set to OFF (marked with *).
NOTE 2: When LFPT is enabled, the LAN port (Fiber port) link down will
force Fiber port (LAN port) link down.
LED Indicators
LED
Color
Description
PWR
Green
Lit if power is connected and active.
Off
Power is not connected.
1000
Green
The connected LAN speed is 1000M.
Off
No 1000M Ethernet link.
100
Green
The connected LAN speed is 100M.
Off
No 100M Ethernet link.
DUP/COL
Green
Full duplex mode.
Green Blinking
Collisions occur on the link.
Off
Half duplex mode.
Fiber
LNK/ACT
Green
The connected LAN speed is 1000M.
Off
No fiber link.
PoE
Green
The LAN port has successfully
negotiated PoE and is supplying output
power to the remote connected PD.
Green Blinking
One of the PoE faults (overload, short
circuit, port failure at startup) occurs.
Off
PD is not connected or output power is
not provided.
LAN and Fiber Connection
FMC-1000-PH & FMC-1000S-PH PoE have 1 electrical LAN port
and 1 fixed fiber port or 1 SFP-based slot on the front panel. The
LAN port utilizes shielded RJ-45 connector that supports
10/100/1000M; while the fiber SFP port supports 1000M (FMC-
1000-PH) or 100/1000M (FMC-1000S-PH).
PoE Port
The LAN port supports PoE (Power over Ethernet) per
IEEE802.3af (15.4W) or IEEE802.3at (30W) for connection to
standard PoE PD (Power Devices) such as IP Cameras, Access
Points, IP Phones, Digital Signage, etc. PoE eliminates the need to
run separate power to these devices thereby simplifying
deployment and reducing expenses.
The LAN ports may also connect to any non-PoE device for
normal Ethernet transmission without any damage to the non-
PoE device or to this device.
RJ-45 Ethernet Port Pinouts
Figure 4. RJ-45 Ethernet Port Pinouts
RJ-45 Ethernet & PoE Pin Assignments
Pin
No.
RJ-45 Ethernet
PoE
Output
100Base-TX
1000Base-T
1
RX+
TRD 0+
V+
2
RX-
TRD 0-
V+
3
TX+
TRD 1+
V-
4
-
TRD 2+
5
-
TRD 2-
6
TX-
TRD 1-
V-
7
-
TRD 3+
8
-
TRD 3-
Wall Mounting Option
FMC-1000-PH & FMC-1000S-PH standalone converters have
the option of adding wall mount capability. One wall mount kit
is required for installing a single standalone unit on the wall.
Each wall mount kit provides all the necessary hardware for a
complete installation.
Application
- 6 -
- 5 -
www.ctcu.com
- 3 -
- 4 -
6
6
2
1
5
1
4
5
4
3
Figure 1.
Rear Panel
Figure 2. Top Panel
Figure 3. Front Panel
Figure 5. Converter with Wall Mounting Bracket
Figure 6. Application for FMC Series Converter