CTC Union IMC-100-PH12 User manual

Installation
The converter comes with both wall mount and DIN rail
hardware brackets. When installing the DIN rail bracket, be sure
to correctly align the orientation pin.
Figure 7. DIN Rail Figure 8. Wall Mount
The converter with DIN Rail bracket has a steel spring in the
upper rail of the bracket. This spring is compressed for mounting
and un-mounting by applying downward force.
Figure 9. Mounting Figure 10.Un-mounting
Introduction
IMC-100-PH(E)12 are Fast Ethernet PoE (Power over Ethernet)
media converters that support conversion between electrical
10/100Base-TX and optical 100Base-FX Ethernet. Housed in
rugged DIN rail or wall mountable enclosures, these converters
are designed for harsh environments, such as industrial
networking and intelligent transportation systems (ITS) and are
also suitable for many military and utility market applications
where environmental conditions exceed commercial product
specifications.
Features
12/24/48VDC (9.6~57VDC) redundant dual input power and
built-in very high efficient power booster
Constant and regulated PoE output voltage at 55VDC
IP30 rugged metal housing
Wide temperature range -20°C ~75°C (IMC-100-PHE12)
Power loss and port link loss alarm indication
Remote PD device reset feature
Industrial grade EMS, EMI, EN50121-4, EN61000-6-2,
EN61000-6-4
Specifications
Optical Interface
Standards: IEEE 802.3u
Speed: 100M
Connector: SC or ST
Multimode (2km) 50/125um, 62.5/125um
Single mode (30km or 50km) 9/125um
Wavelength: 1310nm (S/M or M/M)
Ethernet Interface
Standards: IEEE 802.3, 802.3u
Connector: RJ-45 (shielded)
Auto MDI/MDI-X
Speed: 10/100Base-TX (Auto)
Duplex: Full/Half (Auto)
MTU: 9600K
Link Fault Pass Through (LFP)
Power over Ethernet
1 PoE Enabled port
Supports IEEE 802.3af 15.4W PoE & IEEE 802.3at 30W PoE+
Positive (VCC+) pins 1, 2; Negative (VCC-) pins 3, 6
Data: pins 1, 2, 3, 6
Quick Installation Guide
IMC-100-PH12
IMC-100-PHE12
Industrial Grade Fast Ethernet PoE+ Fiber Converters
Specifications (cont.)
Power
Absolute Range: 9.6~57VDC
Reverse Polarity Protection: Yes
Dual Power Inputs: Yes
Connector: Removable terminal block
Consumption:
Items
Input Voltage
Total Power
Consumption
Device Power
Consumption
PoE
Budget
Boost
Efficiency
12VDC
34W
3.5W
30W
98.4%
24VDC
34.4W
4.1W
30W
99.0%
48VDC
34.9W
4.3W
30W
98.0%
Mechanical
Water & Dust Proof: IP30 Protection
Dimensions: 106 mm (D) x 62.5 mm (W) x 135 mm (H)
Mounting: DIN-Rail, Wall Mount (Kits included)
Weight: 655 g
Environmental
Operating Temperature: -10°C~60°C －IMC-100-PH12
-20°C~75°C －IMC-100-PHE12
Storage Temperature: -40°C~85°C
Humidity: 5%~95% (Non-condensing)
Certifications
EMC: CE
EMI (Electromagnetic Interference): FCC, FCC Part 15 Subpart
B Class A, CE EN55022 Class A
Railway Traffic: EN50121-4
Immunity for Heavy Industrial Environment: EN61000-6-2
Emission for Heavy Industrial Environment: EN61000-6-4
EMS (Electromagnetic Susceptibility) Protection Level:
EN61000-4-2 (ESD) Level 3, Criteria B
EN61000-4-3 (RS) Level 3, Criteria A
EN61000-4-4 (Burst) Level 3, Criteria A
EN61000-4-5 (Surge) Level 3, Criteria B
EN61000-4-6 (CS) Level 3, Criteria A
EN61000-4-8 (PFMF, Magnetic Field) Field Strength:
300A/m, Criteria A
Safety: UL60950-1 (Pending)
Shock: EN60068-2-27
Freefall: EN60068-2-32
Vibration: EN60068-2-6
MTBF (MIL-HDBK-217): 419,822 hours
[email protected]
V1.0
- 2 -
- 1 -
- 7 -
To download this QIG or a more complete user manual, please visit
http://www.ctcu.com/Industrial/
T+886-2-26591021
F+886-2-26590237
E[email protected]
CTC Union Technologies Co., Ltd.
Far Eastern Vienna Technology Center
(Neihu Technology Park)
8F, No. 60 Zhouzi St., Neihu District, Taipei 114
Taiwan
© 2014 CTC Union Technologies Co., Ltd.
All trademarks are the property of their respective owners.
Technical information in this document is subject to change without notice.
www.ctcu.com

Connectors
LAN and Fiber Connection
IMC-100-PH(E)12 media converters have one electrical LAN
port and one fiber port on the front panel. The LAN port that
utilizes shielded RJ-45 connectors supports 10/100M; while the
fiber port supports fixed speed 100M.
PoE Port
The LAN port supports PoE (Power over Ethernet) per
IEEE802.3af (15.4W) or IEEE802.3at (30W) for connection to
standard PoE PD (Power Devices) such as IP Cameras, Access
Points, IP Phones, Digital Signage, etc. PoE eliminates the need to
run separate power to these devices thereby simplifying
deployment and reducing expenses.
The LAN port may also connect to any non-PoE device for
normal Ethernet transmission without any damage to the non-
PoE device or to this device.
RJ-45 Ethernet Port Pinouts
Figure 2. RJ-45 Ethernet Port Pinouts
Operation Mode Switch
DIP
No.
Status
Function
Description
1
OFF *
Enable
Power Alarm
Provide an alarm indication when either
power input loses power.
ON
Disable
Power Alarm
No alarm when either power input loses
power.
2
OFF *
Enable
Port Alarm
Provide an alarm indication when either
copper or fiber port loses link.
ON
Disable
Port Alarm
No alarm when either copper or fiber port
loses link.
3
OFF *
Disable LFP
Disable LFP (Link Fault Pass through).
ON
Enable LFP
LFP (Link Fault Pass through) allows a link
condition to be passed from fiber to TP or
from TP to fiber.
NOTE: LFP is available when the converter is set
to 'Switch' mode (DIP No. 4 is OFF).
4
OFF *
Switch Mode
The device acts as a store & forward device
supporting MAC learning and filtering.
ON
Pass Through
Mode
The device acts as pure 'converter' that the
internal switch is bypassed, enabling low
latency and jumbo (unlimited) frame
support. Do not enable LFP in this mode or
fiber may not link.
NOTE: LAN and Fiber speed must match when
configured in converter mode. If fiber speed is
100M, UTP speed must be 100M.
5
Reserved for future use
6
OFF*
Enable PoE
Enable PoE power output function.
ON
Disable PoE
Disable PoE power output function.
7
OFF*
Disable
Remote PD
Reset
Disable remote PD reset function.
ON
Enable
Remote PD
Reset
When DIP 7 is set to ON, the PSE deice
upon the loss of fiber link will stop supply
power to the connected PD device for 3
seconds. This will force the PD device to
power off and then power on.
8
Reserved for future use
NOTE 1: By default, all DIP switches are set to OFF (marked with *).
NOTE 2: After changing the DIP switch setting, you must restart the device to activate the
setting.
RJ-45 Ethernet & PoE Pin Assignments
Pin
No.
RJ-45 Ethernet
100Base-TX
PoE Output
1
RX+
V+
2
RX-
V+
3
TX+
V-
4
-
5
-
6
TX-
V-
7
-
8
-
Power and Alarm
Power
(PWR1, PWR2)
There are input connectors for two power
sources on the terminal block. Only one
power source is required for normal
operation. The second power source input
may be provided for redundancy.
Alarm
The alarm relay contact can be wired into an
alarm circuit which senses an alarm condition
when the contact is broken. The alarm relay
is normally closed when there is no alarm
condition (See Figure 4). The alarm
conditions are selectable through DIP Switch
to include power and link faults. Please note
that the alarm relay contact can only support
1A current at 24VDC. Do not apply voltage
and current that exceed these specifications.
LED Indicators
LED
Color
Definition
PWR1/
PWR2
Green
Power is connected and active at the
PWR1/PWR2 input terminal connection.
Off
Power is not connected.
Fault
Amber
Fiber link loss, TP link loss or either one
power loss
Off
Normal operation with no power, fiber or
TP faults.
Fiber
LINK/ACT
Green
Fiber port has optical link.
Blinking
Blinking when there is data traffic.
Off
No optical link.
Fiber
Speed
Green
The fiber connected speed is 100M.
LAN
LINK/ACT
Green
LAN port has a link.
Blinking
Blinking when there is Ethernet traffic.
Off
No Ethernet link.
LAN Speed
Green
The UTP (LAN) speed is 100M.
Off
The UTP (LAN) speed is 10M.
PoE
Green
The respective LAN port has successfully
negotiated PoE and is supplying output
power to the remote connected PD.
Blinking
One of the PoE faults (overload, short
circuit, port failure at startup) occurs.
Blinking
twice
The remote PD device performs power
reset.
Off
PD is not connected or output power is not
provided.
Remote PD Reset Application
Figure 1. IMC-100-PH(E)12 Front Panel
Figure 5. DIP Switch
Figure 6. IMC-100-PH(E)12 Remote PD Reset Function
- 6 -
- 5 -
Figure 3. Terminal Block
- 3 -
DIP 6 OFF
DIP 7 ON
www.ctcu.com
2
PSE stops supply PoE
power to PD device for
3 seconds
Fault
Figure 4. Alarm
Relay Circuit
Normally Closed (NC)
PD device
performs a
power reset
Manually disable
or disconnect
fiber link
Power
off
Power
on
IMC-100-PH(E)12
Fiber
PD Device
Switch
1
3
3 seconds
- 4 -