Cuisinart FP8U User manual

Easy Prep Pro
FP8U

2
Important Safeguards
When using electrical appliances, basic safety precautions should
always be followed, including the following:
1. The appliance is not intended to be operated by means of
external timer or separate remote-control system.
2. This appliance is not intended for use by persons with reduced
physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety.
3. Children should always be supervised to ensure that they do not
play with this product.
4. Not for use by children. Keep out of reach of children during
and after use.
5. Always store blades and discs out of reach of children where
they cannot accidently be touched.
6. Keep hands as well as spatulas and other utensils away from
moving blades or discs while processing food to prevent the
possibility of severe personal injury or damage to the food
processor.
7. Avoid contact with moving parts. Never push food down by hand
when slicing or shredding. Always use the pusher accessory.
8. Make sure motor has completely stopped before removing lid.
9. Never store any blade or disc on motor shaft. Store blades and
discs as you would sharp knives, out of the reach of children.
10. Always inspect the appliance before use for noticeable signs of
damage. Do not use if damaged, or if the appliance has been
dropped. Do not use this appliance if the lead is damaged.
In the event of damage, or if the appliance develops a fault,
contact the Cuisinart Customer Care Line (refer to “UK After
Sales.)

3
Congratulations on your purchase of the Cuisinart Easy Prep Pro.
For over 30 years Cuisinart’s aim has been to produce the very
finest kitchen equipment. All Cuisinart products are engineered for
exceptionally long life, and designed to be easy to use as well as to give
excellent performance day after day.
To learn more about our products and for recipe ideas, visit our website
www.cuisinart.co.uk

4
Contents
Product Description.............................................................................. 5
Safety Cautions &Wiring Instructions ............................................. 6
Before First Use .................................................................................. 8
1 Selecting the Work Bowl............................................................... 8
2 Selecting the Blade/Disc ................................................................ 9
3 Setting Up the Food Processor
A Fitting and Removing the Large Work Bowl .................................................................10
B Fitting and Removing the Large Chopping/Mixing Blade .........................................10
C Fitting and Removing the Reversible Slicing and Grating/Shredding Discs..........11
D Setting Up the Small Work Bowl and Chopping/Mixing Blade ...............................12
E Fitting and Removing the Work Bowl Cover .................................................................12
4 Machine Controls ......................................................................... 13
5 Machine Functions
A Chopping .................................................................................................................................14
B Mixing ...................................................................................................................................... 14
C Puréeing/Blending.................................................................................................................14
D Slicing.......................................................................................................................................15
E Grating/Shredding.................................................................................................................15
6 Cleaning &Maintenance ............................................................. 16
7 Troubleshooting ............................................................................ 17
UK Guarantee...................................................................................... 19
UK After Sales Service ....................................................................... 19
Control Buttons

5
Pusher Accessory
Large Chopping/
Mixing Blade
Medium Slicing &
Medium Grating/
Shredding Disc
Work Bowl Cover
Small Work Bowl (max 0.7L)
Control Buttons
Large Work Bowl
(max 1.9L)
Fine Slicing &Fine
Grating/Shredding Disc
Product Description
Feed Tube
Housing Base
Small Chopping/
Mixing Blade
Rubber Seal

6
Safety Cautions
Carefully read all the instructions before using the appliance and keep in a safe place for
future reference.
Always follow these safety cautions when using this appliance to avoid personal injury
or damage to the appliance. This appliance should be used only as described within this
instruction book.
nEnsure all packaging materials and any promotional labels or stickers are removed from
the food processor before first use.
nDo not use this appliance if the lead is damaged. In the event of lead damage discontinue
use immediately. If the lead is damaged it must be replaced by the manufacturer or its
service agent (see ‘UK After Sales Service’ section).
nUnplug from the mains when not in use, before putting on or taking off parts, before
removing food and before cleaning.
nDo not use any accessories or attachments with this appliance other than those recom-
mended by Cuisinart.
nTo protect against fire, electric shock or personal injury, do not immerse cord, plug or
unit in water or other liquids.
nDo not leave the lead hanging over the edge of a kitchen table or worktop.
nAvoid contact between the lead and hot surfaces.
nFor indoor use only.
nFor domestic use only.
nThis appliance should be used only for preparation of drinks / food as described within
the instructions for use that accompany it. Please retain these instructions for future
reference.
nAlways ensure that your hands are dry before removing the plug from the mains outlet.
Never pull the plug out of the mains outlet by its lead.
nTo avoid injury or possible fire, do not cover the appliance when in use.
nDo not connect this appliance to an external timer or remote control system.
nThis appliance complies with the basic requirements of Directives 04/108/EEC (Elec-
tromagnetic Compatibility) and 06/95/EEC (Safety of domestic electrical appliances).
WARNING: Polythene bags over the product or packaging may be dangerous. To
avoid danger of suffocation, keep away from babies and children. These bags are
not toys.

7
UK Wiring Instructions
The wires in the mains lead are coloured in accordance with the following code:
nBLUE = NEUTRAL
nBROWN = LIVE
As the colours of the wire in the mains lead of this appliance may not correspond with the
colour marking identifying the terminals on your plug, proceed as follows:
nThe wire which is coloured BLUE must be connected to the terminal which is marked
with the letter N
nThe wire which is coloured BROWN must be connected to the terminal which is marked
with the letter L
nNeither the BLUE or BROWN wires should be connected to the terminal which is marked
with the letter E or the symbol
This appliance is supplied fitted with a BS1363 mains plug and a BS1362 13A fuse. If this
plug is removed from the appliance please ensure it is disposed of safely as a disconnected
plug is dangerous if reconnected to the mains. If any other type of plug is used, a 13A fuse
must be fitted.
The symbol on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused
by inappropriate waste handling of this product. For more detailed information about the
recycling of this product, please contact your local council office or your household waste
disposal service.

8
Before First Use
Take care when unpacking the chopping/mixing blades and the reversible slicing/
grating discs. The blades are very sharp and could cause injury.
To avoid injury, ensure the raised finger grips on the plastic casing are used to remove the
blades from their plastic packaging and carefully remove cardboard and tape from the
reversible slicing/grating discs. Retain the plastic casings for safe storage.
Before using your Cuisinart Easy Prep Pro for the first time, wash the large and small
work bowls, work bowl cover, pusher accessory, chopping/mixing blades, and both slicing/
grating discs.
1. Selecting the Work Bowl
nThe Food Processor is supplied with two work bowls.
nThe large work bowl has a maximum capacity of 1.9L and can be used with the large
chopping/mixing blade and the two reversible slicing and grating/shredding discs.
nThe small work bowl has a maximum capacity of 0.7L and can be used with the small
chopping/mixing blade only. The seal on the inner bowl prevents any leakage into the
large work bowl, allowing you to use the small bowl without the need to wash up the
large bowl after use.
N.B. The large work bowl must always be fitted before the small work bowl can be set up
inside.
It will not always be possible to use the work bowls to their maximum capacity. The
amount of food/liquid you can process in the bowls will depend on the density of the
ingredients in the work bowl and the consistency of the desired end result. For example,
to achieve a consistent result when chopping or pureeing nuts, fruits, vegetables or meats
you may need to process in batches of 300-500g . If you are mixing dough which can be
very dense, you may need to process in batches of around 400g.
If you find that the motor is struggling or that the processing results are uneven, then
we would recommend that you reduce the amount of ingredients in the work bowl and
instead process in batches.
For liquid, we recommend that you do not fill the bowls above the Maximum Liquid Fill
markings on each bowl (900ml on the large work bowl and 300ml on the small work
bowl.) This is to avoid liquid spilling into the central spindle which may cause leakage.

9
2. Selecting the Blade/Disc
For chopping, mixing, blending and puréeing use the chopping/mixing blades.
nThe large chopping/mixing blade can only be used with the large work bowl.
nThe small chopping/mixing blade can only be used with the small work bowl.
For slicing and grating/shredding use one of the reversible discs.
nUse one disc for fine slicing (2mm) and fine grating/shredding.
nUse the other disc for medium slicing (4mm) and medium grating/shredding.
Both discs are labelled accordingly.
Fine Slicing or Fine Grating/Shredding
Medium Slicing or Medium Grating/Shredding
Fine Slicing Fine Grating/Shredding
Medium Slicing Medium Grating/Shredding
FP-8FD
FINE SLICING
MADE IN CHINA
FABRIQUÉ EN CHINE
FP-8FD
FINE SHREDDING
MADE IN CHINA
FABRIQUÉ EN CHINE
FP-8MD
MEDIUM SLICING
MADE IN CHINA
FABRIQUÉ EN CHINE
FP-8MD
MEDIUM SHREDDING
MADE IN CHINA
FABRIQUÉ EN CHINE

10
3. Setting Up the Food Processor
A Fitting and Removing the Large Work Bowl
nPlace the food processor base on a dry, flat, sturdy surface.
nPlace the large work bowl over the motor spindle, ensuring that the handle of the bowl
is positioned to the right of the centre.
nTurn the work bowl in a clockwise direction until it locks into position on the housing
base.
nTo remove, grasp the handle and turn the work bowl anti-clockwise until it unlocks. Lift
up and away.
N.B. The work bowl may be stiff during the first few times of use.
B Fitting and Removing the Large Chopping/Mixing Blade
nSet up the large work bowl as directed in 3A.
nHolding the central plastic stem, carefully lift and place the large chopping blade over
the work bowl’s centre spindle. Push the blade down until it can go no further.
N.B. Always fit the blade in the bowl before adding ingredients.
nTo remove, hold the central plastic stem of the blade and lift up and away from the work
bowl’s centre spindle.
WARNING: Take great care when handling the blades; they are sharp and can cause
injury.
Large Chopping/Mixing Blade
Push down
Centre Spindle of Large
Work Bowl

11
C Fitting and Removing the Reversible Slicing &Grating/Shredding Discs
The reversible slicing and grating/shredding discs can only be used with the large
work bowl.
nSet up the large work bowl as directed in 3A.
nChoose the desired disc and place it on the motor spindle, ensuring the text for the
function you wish to use is facing upwards on the disc (see section 2 for your reference).
nSlowly twist until the disc and spindle grooves align; the disc will fall into place.
N.B. Never put either disc on the motor spindle until the work bowl is locked in place.
nTo remove, carefully lift the disc upwards and away from the motor spindle.
WARNING: Take great care when handling either disc; the slicing blades are sharp
and can cause injury.
Place disc on
motor spindle

12
D Setting Up the Small Work Bowl &Chopping/Mixing Blade
The small chopping/mixing blade can only be used with the small work bowl.
nSet up the large work bowl as directed in 3A.
nPlace the rubber seal around the circumference of the small bowl, ensuring the lip
of the band covers the top of the bowl. Make sure the seal is fitted correctly so that
contents do not spill over the edge into the large work bowl. This allows you to use both
bowls for separate tasks without the need for washing up in between.
nPlace the small work bowl onto the large work bowl’s centre spindle.
nHolding the central plastic stem, carefully lift and place the small chopping/mixing
blade over the large work bowl’s centre spindle. Gently push the blade down until it
can go no further.
N.B. Always put the blade in the bowl before adding ingredients.
nTo remove, hold the central plastic stem of the blade and lift up and away from the
centre spindle.
WARNING: Take great care when handling the blades; they are sharp and can cause
injury.
E Fitting and Removing the Work Bowl Cover
nPlace the work bowl cover on top of the work bowl, with the feed tube just to the right
of the centre. Turn clockwise to lock onto the work bowl, ensuring the feed tube aligns
with the handle of the large work bowl.
nAlign the pusher accessory with the feed tube opening on the work bowl cover and slide
down to the bottom.
nTo remove the cover, grasp the feed tube and slide anti-clockwise to unlock and lift
away.
Push
Down

13
4. Machine Controls
High and Low Control Buttons
nThe ‘HIGH’ or ‘LOW’ controls are buttons that allow the machine to run until ‘OFF’ is
selected.
nProperly assemble the machine.
nAdd ingredients to the work bowl, either through the feed tube or directly into the bowl.
Ensure the work bowl cover is correctly fitted.
nPress the ‘HIGH’ or ‘LOW’ button. The blue LED light will illuminate and the motor will
start.
nPress the ‘OFF’ button when finished.
WARNING: The unit has a built in safety mechanism which will automatically turn off the
motor if the work bowl cover is removed. If the ‘OFF’ button hasn’t been pressed, when the
work bowl cover is replaced, the motor will start up automatically. Simply press the ‘OFF’
button to stop the motor.
Pulse Button
The ‘PULSE’ control is a button that allows the machine to run only while it is being
pressed. This capability provides more accurate control of the duration and frequency of
processing. Unless otherwise specified, a ‘PULSE’ should be about one second.
With the machine properly assembled, ingredients in the work bowl and the work bowl
cover correctly fitted, press the ‘PULSE’ button repeatedly as needed. The blue LED High
light will illuminate upon activation. As you get used to using the processor you will get
to know which setting works best for the food you are using.

14
5. Machine Functions
A Chopping
nYou can use your machine for a wide range of chopping tasks, including chopping
meats, fish, fruits, vegetables, cheeses and nuts.
nSet up your chosen bowl and the appropriate mixing/chopping blade.
nFor raw ingredients: peel, core and/or remove seeds and pips. For best results ensure
that the pieces of food you add to the work bowl are approximately the same size, i.e.
2.5cm cubed.
nAdd ingredients and pulse food in 1-second increments to chop. For the finest chop,
either hold the ‘PULSE’ down or press ‘HIGH’ or ‘LOW’ to run the machine continuously.
Watch ingredients closely to achieve desired consistency and scrape the work bowl as
necessary.
nHigh speed is recommended for most chopping.
WARNING! Never try to process ingredients that are too hard to cut with a knife. You may
damage the blade or the appliance.
B Mixing
nYou can produce dips, dressings, sauces, cake mixture, bread dough, pastry and crumble
toppings.
nSet up your chosen bowl and the appropriate mixing/chopping blade.
nAdd ingredients to the selected work bowl and use the ‘PULSE’ function or ‘LOW’ speed
(recommended for making doughs and batters).
nWatch ingredients closely to achieve desired consistency and scrape the work bowl as
necessary.
nLiquids can be added through the feed tube while the machine is running.
C Puréeing/Blending
nSet up your chosen bowl and the appropriate mixing/chopping blade.
nIngredients should be cut into 2.5cm pieces; a smooth purée is best achieved when all
the pieces are of equal size.
nPulse to initially chop and then process ‘HIGH’ or ‘LOW’ until food is puréed/blended;
scrape the work bowl as necessary.
N.B. Do not use this method to purée cooked white potatoes. They develop a gluey texture
when processed with the metal blade.
nPurée solid ingredients and add any liquids slowly via the feed tube as required.

15
D Slicing
nUse the slicing discs for perfect 2mm or 4mm slices.
nSet up your chosen slicing disc with the large work bowl and fit the work bowl cover.
nTurn the machine onto ‘HIGH’.
nEnsure the pusher accessory is removed, then place the food into the feed tube. For best
results, always pack food evenly into the tube. Ingredients should fit snugly, but not so
tightly that it prevents the pusher accessory from moving.
nUsing the pusher accessory, slowly push the food down the feed tube until it makes
contact with the disc and is sliced.
N.B The position of the food in the feed tube will determine the shape and size of the
slices. For example, if you insert a whole carrot vertically you will get round slices. To
change the shape and size of the slices change the position of the food in the feed tube.
The type/texture of the food will dictate the amount of pressure required. Use light
pressure for soft foods, medium pressure for medium foods, and firm pressure for harder
foods. Always process with even pressure.
WARNING: Never put fingers into the feed tube; always use the pusher accessory
provided. If food becomes stuck, turn the machine off, unplug from the main electric
supply and dismantle the processor. Do not attempt to remove food whilst the disc
is in operation.
E Grating/Shredding
nUse the grating/shredding discs for fine or medium shredding/grating.
nSet up your chosen grating/shredding disc with the large work bowl and fit the work
bowl cover.
nTurn the machine onto ‘HIGH’.
nEnsure the pusher accessory is removed, then place the food into the feed tube. For best
results, always pack food evenly into the tube. Ingredients should fit snugly, but not so
tightly that it prevents the pusher accessory from moving.
nUsing the pusher accessory, slowly push the food down the feed tube until it makes
contact with the disc and is grated/shredded.
The type/texture of the food will dictate the amount of pressure required. Use light
pressure for soft foods, medium pressure for medium foods, and firm pressure for harder
foods. Always process with even pressure.
WARNING: Never put fingers into the feed tube; always use the pusher accessory
provided. If food becomes stuck, turn the machine off, unplug from the main electric
supply and dismantle the processor. Do not attempt to remove food whilst the disc
is in operation.

16
6. Cleaning &Maintenance
nWhen not in use, leave your food processor unplugged.
nKeep the blades and discs out of the reach of children.
nAll parts except the housing base are dishwasher safe. We recommend washing
them in the dishwasher on the top rack. Due to intense water heat, washing the
work bowl(s), cover and accessories on the bottom rack may cause damage over
time. Insert the work bowl(s) and pusher accessory upside down for drainage.
Take extra care when loading and unloading blades and discs in the dishwasher.
N.B Due to food staining, it is normal for the rubber seal to become discoloured over
time. We recommenced to remove, clean and replace the rubber seal on the small work
bowl after each use.
nTo simplify cleaning, rinse the work bowls, work bowl cover, pusher accessory and blade
or disc immediately after use so food won’t dry on them. If food lodges in the pusher
accessory, remove it by running water through it, or use a bottle brush.
nIf you wash the blade and discs by hand, do so carefully. When handling, use the plastic
stems. Avoid leaving them in soapy water where they may disappear from sight. To
clean the metal blade, fill the work bowl with soapy water, hold the blade by its plastic
stem and move it rapidly up and down on the centre spindle of the bowl.
nThe work bowls are made of SAN plastic. They should not be placed in a microwave
oven.
nDo not use abrasive cleaners on the housing base, simply wipe with a damp cloth and
dry thoroughly. Apply any cleaning agent to the cloth, not the base.
nIf the feet leave spots on the counter, spray them with a spot remover and wipe with
a damp sponge.
nIf any trace of the spot remains, repeat the procedure and wipe the area with a damp
sponge and non-abrasive cleaning product.
IMPORTANT: Never store any blade or disc on the motor spindle. No blade or disc should
be placed on the spindle except when the processor is about to be used.
MAINTENANCE: Any other servicing should be performed by an authorised service
representative.

17
7. Troubleshooting
Q The food is unevenly processed.
A: The ingredients should be cut evenly into 2.5cm pieces before processing.
A: Process in batches to avoid overloading.
Q: Slices are uneven or slanted.
A: Place evenly cut food, cut side down, into the feed tube. Apply even pressure on the
pusher accessory.
Q: Food falls over in feed tube.
A: Feed tube should be packed full and evenly for best results. Ingredients should fit
snugly, but not so tightly that it prevents the pusher accessory from moving.
Q: Some food remains on top of the disc.
A: It is normal for small pieces to remain; cut remaining bits by hand and add to processed
ingredients.
Q: The motor does not start.
A: There is a safety interlock to prevent the motor from starting if it is not properly
assembled. Make sure the work bowl(s) and work bowl cover are securely locked into
position. If the motor still will not start, check the power cord and outlet.
Q: The food processor shuts off during operation.
A: The cover may have become unlocked; check to make sure it is securely in position. A
safety protector in the motor prevents the motor from overheating, which is caused by
excessive strain. Press the ‘OFF’ control button and wait 20 to 30 minutes to allow the
food processor to cool off before resuming.
Q: Unable to lock the work bowl cover
A: Ensure the rubber seal is fully fitted to the small work bowl, making sure the lip of the
band is covering the bowl’s circumference and isn’t raised/loose at any point.
Q: The motor slowed down during operation.
A: This is normal as some heavier loads e.g slicing/shredding cheese may require the motor
to work harder. Simply reposition the food in the feed tube and try again.
A: Alternatively, the maximum load capacity may have been exceeded. Remove some of
the ingredients and continue processing.
Q: The food processor vibrated/moved around the countertop during processing.
A: This is normal as some heavier loads (e.g. slicing/ shredding cheese) may require the
motor to work harder.
A: Make sure the rubber feet at the bottom of the unit are clean and dry. Also make sure
that the maximum load capacity is not being exceeded.

18
Q: Liquid is leaking from the small bowl into the large work bowl beneath
A: Check that the rubber seal is correctly fitted on the small work bowl.
A: Check that the maximum liquid fill mark has not been exceeded. If you are processing
liquid above the maximum fill line then it is possible for liquid to leak down through the
central spindle.

19
UK Guarantee
nThis Cuisinart Food Processor has a 5 year guarantee for domestic use.
nThe guarantee covers defects under normal use from date of purchase and ceases to be
valid in the event of alteration or repair by unauthorised persons.
nIf the appliance does not perform satisfactorily due to defects of material or manufacture,
it will be repaired or replaced by the manufacturer (see ‘UK After Sales Service’ for
details).
nThis guarantee is only valid in the United Kingdom and Eire (includes Channel Islands
and Isle of Man).
nNo responsibility will be accepted for any damage caused in transit.
nA charge may be made if goods are returned outside the relevant guarantee period or if
the product is returned unnecessarily.
nThe manufacturer reserves the right to amend terms and specifications without prior
notice.
nThis guarantee in no way affects your statutory rights.
UK After Sales Service
For further advice on using the appliance or should you need to return your product,
please contact the Conair Customer Care Line on 03702 406 902 (09:00 to 17:00
Monday to Friday) or email your enquiry to [email protected]
Customer Care Centre,
Conair Logistics
Unit 4, Revolution Park
Buckshaw Avenue
Buckshaw Village
Chorley
PR7 7DW
Please enclose your returns number, name and address details, together with a copy of
proof of purchase and details of the fault.

www.cuisinart.co.uk
IB-15/334