Cuisinart PE-50 User manual

Pasta Extruder Attachment
INSTRUCTION
BOOKLET
AND RECIPES
PE-50
For your safety and continued enjoyment of this product, always read
the Instruction Book carefully before using.

2
CONTENTS
Important Safeguards.................... 2
Special Cord Set Instructions ....... 3
Unpacking Instructions.................. 3
Parts and Features ........................4
Attaching to Stand Mixer............... 5
Operation ....................................... 5
Cleaning and Maintenance............ 6
Tips and Hints .............................. 7
Recipes ......................................... 8
IMPORTANT
SAFEGUARDS
When using electrical appliances,
basic safety precautions should
always be taken, including the
following:
1. READ ALL INSTRUCTIONS
BEFORE USING.
2. Turn dial to the OFF position
and unplug the Cuisinart®
Stand Mixer before tting or
removing the pasta extruder
attachment, after use and
before cleaning.
3. Close supervision is necessary
when any appliance is used
by or near children. Cuisinart
does not recommend the use
of this appliance by children
or individuals with certain
disabilities.
4. NEVER FEED FOOD BY
HAND; ALWAYS USE THE
PUSHER. Avoid contact
with moving parts and tted
attachments. To reduce the
chances of bodily injury and/
or damage to the Stand Mixer
or pasta extruder attachment,
keep hands, clothing, cooking
utensils, etc., away from the
moving parts during operation.
5. The use of attachments not
recommended or sold by
Cuisinart may cause re,
electric shock or injury.
6. Do not use more than one
attachment at a time.
7. Do not exceed the maximum
capacities listed in this
instruction booklet.
8. Do not use the Stand Mixer or
attachment if it is damaged
or if the cord is damaged.
Have it checked and serviced
before resuming use.
9. Do not use this attachment
for anything other than its
intended use.
10. Do not use outdoors.
11. To protect against the risk of
electric shock, do not put the
power base unit in water or
other liquids.
12. Do not let cord hang over edge
of table or counter.
13. Never leave your pasta
extruder attachment
unattended while the Stand
Mixer is running.
14. The attachments are intended
for use with the basic
appliance (SM-50).
15. Do not operate your appliance
in an appliance garage or
under a wall cabinet. When
storing in an appliance garage
always unplug the unit from
the electrical outlet. Not doing
so could create a risk of re,
especially if the appliance
touches the walls of the garage
or the door touches the unit as
it closes.

3
SAVE THESE
INSTRUCTIONS
FOR HOUSEHOLD
USE ONLY
SPECIAL CORD SET
INSTRUCTIONS
A short power-supply cord is
provided with the Stand Mixer to
reduce the risks resulting from
becoming entangled in or tripping
over a longer cord.
Longer extension cords are available
and may be used if care is exercised
in their use.
If a long extension cord is used,
the marked electrical rating of the
extension cord must be at least as
great as the electrical rating of the
appliance, and the longer cord
should be arranged so that it will
not drape over the countertop or
tabletop where it can be pulled
on by children or tripped over.
UNPACKING
INSTRUCTIONS
1. Place the gift box containing your
Cuisinart®Pasta Extruder Stand
Mixer Attachment on a at, sturdy
surface before unpacking.
2. Lift the corrugated insert out of
the gift box. Remove the body,
wrench, and pasta plates.
To assemble the pasta extruder
attachment, follow Assembly
Instructions on page 5. Replace all
packaging materials inside box and
save the box for repackaging.
Before using for the rst time: Wash
all parts according to Cleaning and
Maintenance on page 6.
WARNING
RISK OF FIRE OR ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY

4
PARTS AND FEATURES
1. Body
2. Feed Tube
3. Feed Screw
4. Ring Nut
5. Wrench/Pusher/
Feed Screw Remover
6. Pasta Cutter Ring
7. Six Different Pasta Plates
You can make the pasta
of your choice.
7a. Pasta Plate for Spaghetti
7b. Pasta Plate for Small
Macaroni
7c. Pasta Plate for Rigatoni
7d. Pasta Plate for Fusilli
7e. Pasta Plate for Bucatini
7f. Pasta Plate for
Large Macaroni
8. Pasta Plate Storage Case
7a
7d
7b
7e
7c
7f
5
3
1
2
6
4
8

5
ASSEMBLY
INSTRUCTIONS
1. Insert the feed screw, metal
end first, into the front end of
the pasta extruder body.
Rotate until the plastic X on
the feed screw lines up with
the X-shaped groove inside
the pasta extruder body.
2. Fit one of the pasta plates on
top of the feed screw. Make
sure that the notches on the
four sides of the pasta plate
slide securely onto the four
grooves on the front end of
the body.
3. Fit the ring nut over the pasta
plate and turn it clockwise
until it is secured to the body.
4. Attach the pasta cutter by
sliding it over the ring nut and
aligning the two notches on
the side of the cutter with the
two grooves on the pasta
extruder body. Push in firmly,
and while pushing firmly, turn
the cutter clockwise to
secure. It should move freely
around the pasta plate and
extruder body.
5. To s w i t ch the pasta plate, first
remove the pasta cutter, then
the ring nut and current pasta
plate, then follow assembly
instructions 2 to 4 with the
new pasta plate. Make sure
there is no pasta dough
obstructing the round groove
located in the center of the
feed screw.
ATTACHING TO
STAND MIXER
1. Make sure Stand Mixer is OFF.
2. Gently pull outlet
cover off front
of mixer head to
remove.
3. Turn the Stand
Mixer attachment
knob counter-
clockwise until
outlet opening is
unobstructed.
4. Insert the
assembled
extruder
attachment
into the outlet
opening, lining
up the square metal hub on
the extruder with the square
indentation in the outlet
opening.
5. Turn the Stand Mixer
attachment knob clockwise to
secure to mixer.
OPERATION
1. Prepare pasta dough as
directed by recipe, letting it
rest in the refrigerator until it is
ready to be extruded.
2. Cut dough into 1-inch pieces.
Cover with plastic wrap or
a damp paper towel so it
doesn’t dry out.

6
3. Line a sheet tray with parch-
ment paper and generously
dust with semolina our to
keep pasta from sticking. Set
sheet below extruder attach-
ment.
4. Set Stand Mixer to Speed 5
and slowly drop in 4 pieces of
dough, one at a time, without
using the pusher (if making
spaghetti or bucatini, use
Speed 10). Do not overll.
NOTE: Dough will “knead” in
the extruder chute for about
1 minute, before extrusion
begins.
5. When extruded pasta reaches
desired length, use the pasta
cutter ring to cut it, by turning
the cutter rst to the left and
then quickly to the right; let
cut pasta fall onto dusted
sheet tray. If pasta dough
sticks to the back of the cutter
this may lead to unclean cuts.
If this is the case rst stop the
unit, remove the pasta cutter
ring and clean out any stuck
dough. Replace cutter ring
and continue with remaining
dough. If this continues to
occur dough may be too soft.
To prevent this from occur-
ring dust each piece of dough
in “00” our before putting
through the extruder.
6. Drop in more dough pieces,
one at a time, as pasta is
extruded and cut. Generously
dust all cut pasta with more
semolina our.
7. Repeat extrusion and cut-
ting process with remaining
dough pieces. NOTE: Pasta
can be cooked immediately or
generously dusted with semo-
lina our, dried and stored in
airtight bags in the refrigerator.
8. Boil pasta in generously salted
water to desired doneness.
Recommended cooking
time is about 3 minutes for
spaghetti and 6 minutes for al
dente rigatoni, though cooking
times vary (see Tips and Hints
section).
CLEANING AND
MAINTENANCE
1. Remove the pasta cutter
manually by pushing it rmly
and rotating it counter-
clockwise to release the
notches from the grooves on
the pasta extruder body. Then
remove the ring nut manually
or with the wrench if it is
fastened too tightly.
2. Feed screw can be removed
by using the hook on the top
of the wrench/pusher.
Please note: the feed screw
metal washers may be very
hot. Let cool before touching.
3. Allow dough on the pasta
plates to dry before cleaning.
Once dough is dry, separate
the plastic and metal pieces
of the pasta plates and gently
tap out any loose dough. To
remove stubborn dry dough,
using a wooden or plastic
skewer, or toothpick, is help-

7
ful. Do not use metal tools to
scrape off dough or you may
cause damage to the plates.
The pasta plate pieces are
marked for easy assembly.
F = Fusilli
B = Bucatini
R = Rigatoni
LM = Large Macaroni
SM = Small Macaroni
S = Spaghetti
4. Do not wash pasta extruder
housing in dishwasher or
immerse in water or other
liquids. Wipe extruder with
damp cloth. Wash ring nut
in warm, soapy water. Do
not put the ring nut or pasta
plates in the dishwasher.
Pasta plates can be washed
in warm, soapy water and are
top-rack dishwasher safe.
5. Any other servicing should be
performed by an authorized
service representative.
Tips and Hints
• It is essential to stir the our
before you measure it. Do not
scoop it right out of the bag.
• The key to making fresh pasta
is to have the right feel of the
dough – not too moist or too
dry. Dough should be pliable
and come together in one ball,
yet should not be sticky to the
touch.
• The humidity of the day can
greatly affect the pasta dough.
If the day is very humid, watch
and feel the dough when you
are nished kneading. If it is
still sticky, knead in one table-
spoon of our at a time until
the stickiness disappears.
• Always add pasta dough to
feed tube slowly, waiting a
couple of minutes for it to
knead in the chute and begin
extruding before adding more.
Do not overll, which will cause
pasta to extrude very slowly.
• If pasta extrudes too slowly,
turn off the Stand Mixer and
carefully remove some dough
from the pasta extruder chute.
• If a piece of pasta gets stuck,
turn off the Stand Mixer and
gently nudge lodged dough
piece with the back of the
wrench.
• A pasta cutter is included to
cut pasta, but a paring knife or
metal bench scraper can also
be used.
• Try to cut pasta into similar
lengths to ensure even
cooking.
• The dough may come out curly
in the rst batch. The dough
should straighten in the sec-
ond batch. Any curled pasta
can be reprocessed.
• Separate pasta as soon as it
is cut from the pasta extruder.
Toss freshly extruded pasta
with semolina our to prevent
sticking. Pile dusted noodles
together in loose bundles on a
at, clean surface.
• To cook pasta, add 1 table-
spoon of salt and 1 tablespoon
of oil to 6 quarts boiling water.
Add pasta slowly and sepa-

8
rately; make sure no pasta is
sticking together before adding
to water. Cook as directed,
stirring occasionally. Drain
in colander.
• Fresh pasta is best if cooked
immediately. Store up to 5
days in the refrigerator, rst
air-drying for one hour, then
sealing in plastic bag.
• Generously dusted fresh pasta
can be “dried” to achieve a
texture more similar to dried,
boxed pasta. Simply let it sit at
room temperature for up to 4
hours before storing.
• Fresh pasta cooks much faster
than dried, boxed pasta, but
cooking times will vary based
on size and thickness of any
pasta. As you work with your
homemade pastas, you will
learn the timing that works
best.
• The Stand Mixer should rest at
least one hour after processing
2 pasta dough recipes.
• Generously dust pasta with
semolina our after extruding
to prevent sticking. Excess
our will fall off during cooking.
Recipes
Basic Pasta Dough
The combination of “00”
and semolina flour gives this
dough the perfect bite when
cooked, compared to traditional
pasta dough made with just
semolina flour.
Makes about 1 pound;
4 to 5 servings
5 large eggs
2½cups “00” flour, plus
more as needed for
kneading
2/3cup semolina flour
1. Put all of the ingredients, in
the order listed, into the
Cuisinart®mixing bowl. At-
tach the dough hook and
mix on Speed 5 to combine,
about 1 minute.
2. Continue mixing until dough
mostly comes together, an
additional 4 to 6 minutes. At
about 5 minutes of mixing,
check the texture. If it is too
dry, add water one table-
spoon at a time; alternatively,
if it is too wet, add the “00”
our one tablespoon at a time
to desired consistency. Keep
in mind, this dough will not
resemble a smooth ball; it will
only just come together in
large chunks with some pos-
sible smaller bits to knead in
by hand. Should any our or
loose dry bits be left behind
at the bottom of the bowl,
leave them there and do not

Aditamento extrusor de pasta
MANUAL DE
INSTRUCCIONES/
LIBRO DE RECETAS
PE-50
Para su seguridad y para disfrutar plenamente de este producto,
siempre lea cuidadosamente las instrucciones antes de usarlo.

2
ÍNDICE
Medidas de seguridad importantes .. 2
Uso de extensiones........................ 3
Instrucciones de desembalaje..... .. 3
Piezas y características.................. 4
Conexión a la batidora de pie ........ 5
Operación....................................... 6
Limpieza y mantenimiento .............7
Consejos y sugerencias .................7
Recetas ......................................... 9
MEDIDAS DE
SEGURIDAD
IMPORTANTES
Al usar aparatos eléctricos, siempre
debe tomar precauciones básicas
de seguridad, incluso las siguientes:
1. LEA TODAS LAS
INSTRUCCIONES ANTES DE
USARLO.
2.
Apague (“OFF”) y desconecte la
batidora de pie Cuisinart
®
antes
de instalar/retirar el aditamento
extrusor de pasta, después del
uso y antes de la limpieza.
3. Supervise el uso de este aparato
cuidadosamente cuando sea
usado por o cerca de niños.
Cuisinart no recomienda que
los niños o personas con ciertas
discapacidades usen este
aparato.
4. NUNCA INTRODUZCA LA
MANO EN LA BOCA DE
ALIMENTACIÓN; SIEMPRE
USE EL EMPUJADOR. Evite el
contacto con las piezas móviles y
los accesorios/aditamentos. Para
evitar el riesgo de heridas y/o
daños al aparato o al aditamento,
mantenga las manos, el cabello,
la ropa y los utensilios alejados
de las piezas móviles durante el
funcionamiento.
5. El uso de accesorios/
aditamentos no recomendados
o vendidos por Cuisinart
presenta un riesgo de incendio,
electrocución o heridas.
6. No use más de un aditamento a
la vez.
7. No exceda las capacidades
máximas indicadas en este
manual de instrucciones.
8. No utilice el aparato ni el
aditamento si estuvieran
dañados o si el cable estuviera
dañado;
regréselos a un centro de
servicio autorizado para que los
revisen y los reparen.
9. No utilice este aditamento para
ningún otro fin que no sea el
indicado.
10. No lo utilice en exteriores.
11. Para reducir el riesgo de
electrocución, no coloque la
base del aparato en agua ni en
ningún otro líquido.
12. No permita que el cable
cuelgue del borde de la mesa o
de la encimera.
13. Nunca descuide/deje sin
vigilancia el aditamento
mientras la batidora de mano
está funcionando.
14.
Este accesorio ha sido diseñado
para ser usado con la batidora
de pie Cuisinart SM-50.
15. No haga funcionar el aparato
debajo o dentro de un armario/
gabinete. Siempre desconecte
el aparato antes de guardarlo
en un armario/gabinete.
Dejar el aparato conectado
presenta un riesgo de incendio,
especialmente si este toca las
paredes o la puerta del armario/
gabinete cuando cierra.