Curt Manufacturing 13337 User manual

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
3500 525
4000 525
LEXUS NX200t/NX300h
5/7/2020
13337
40
36
20
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
Scan
for more
information
Parts List
DESCRIPTIONPART NUMBERQTYITEM
HHCS,M12x1.25,35,CL10.9,YZ
10-1027541
WASHER,S-CON,1/2,YZ
30-0014942
1. Lower the exhaust by removing the (3) rearmost rubber exhaust isolators. Note: Support the exhaust during
installation to prevent damage.
(See Rubber Isolator Removal Diagram.)
2. Raise hitch into position and loosely secure hitch with M12 bolts and conical washers.
3. Torque all M12 fasteners to 60 ft-lbs.
4. Raise exhaust and reinstall the rubber isolators.
EXISTING WELDNUTS
(BOTH SIDES)
PASSENGER SIDE
FRAME RAIL
DRIVER SIDE
FRAME RAIL
2
1
- LOWER EXHAUST
- NO DRILLING
TOOLS REQUIRED
RATCHET
TORQUE WRENCH
19mm SOCKET
SAFETY GLASSES

MAKE: STYLE:
MIN.
20
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
For more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com
WEIGHT CARRYING:
INSTALLATION TIPS:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY:
EASY
MODERATE CHALLENGING
Safety glasses should be
worn at all times while
installing this product
.
YEARS: 2015-PRESENT LEXUS MODEL: NX200t/NX300h SUV
3500
525
TRAILER WEIGHT:
TONGUE WEIGHT:
13337 INSTALLATION INSTRUCTIONS
LBS.
LBS.
WEIGHT DISTRIBUTION: TRAILER WEIGHT:
TONGUE WEIGHT:
4000
525
LBS.
LBS.
MIN.
40
IF YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
NOVICE INSTALL TIME:
PRO INSTALL TIME:
SCAN FOR
MORE INFO
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product
voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.com
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
5/7/2020
EASY
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
INSTRUCTIONS THOROUGHLY.
2. TO EASE INSTALLATION, 2 PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL AND REDUCE THE
TIME REQUIRED.
4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 877-287-8634
RATCHET
TORQUE
WRENCH SOCKET
19mm
REMOVE (3) EXHAUST HANGERS
WELDNUT CLEANING
NO DRILLING
SAFETY
GLASSES

INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
HHCS,M12x1.25,35,CL10.9,YZ10-10275
4
1
WASHER,S-CON,1/2,YZ
30-0014942
2
1
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
EXISTING WELDNUTS
(BOTH SIDES)
1. Lower the exhaust by removing the (3) rearmost rubber
exhaust isolators. Note: Support the exhaust during
installation to prevent damage.
(See Rubber Isolator Removal Diagram.)
2. Raise hitch into position and loosely secure hitch with
M12 bolts and conical washers.

INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
3. Torque all M12 fasteners to 60 ft-lbs.
4. Raise exhaust and reinstall the rubber isolators.