Curt Manufacturing 45950 User manual

CURTMFG.COM •NEED ASSISTANCE? •877.287.8 634 •45950-INS-RA •PAGE 1
Maintenance
Mild automotive detergent may be used to
clean the product. Do not use dish detergent,
abrasive cleaners, abrasive pads, wire
brushes or other similar products that
may damage the finish.
Weight Capacity
Gross trailer weight (GTW) 15,000 lbs.
Tongue weight (TW) 1,500 lbs.
INSTALLATION MANUAL 45950
Tools Required
Socket, 3/4" Torque wrench
Product Photo
Parts List
Item Qty Description
1 1 Adjustable shank*
2 1 Pintle mount
3 2 Pin*
4 2 Clip*
5 4 Hex bolt
6 4 Lock washer
*Sold separately
Level of Difficulty
Easy
WARNING
Never exceed the vehicle manufacturer's recommended towing capacity. The ratings of
the mount system are intended to represent the capability of the product and in no way
reflect the ratings or capacity of the towing system it is being used with. The consumer
or operator are strongly advised to learn the ratings of the various components of the
towing system and never exceed the limits of the lowest rated component being used.
Never hook up trailer safety chains to the mount system. Ensure the safety
chains operate freely around the mount system and do not become entangled.
NOTICE
Before you begin installation, read all instructions thoroughly.
Prior to towing, ensure all fasteners are tight and all structural components are sound.
Using a torque wrench and 1/2" socket, torque hardware to 75 lb-ft.
Product Registration
CURT Group stands behind our products with industry-leading warranties.
Provide feedback and help us to improve our products by registering your purchase at:
warranty.curtgroup.com/surveys

CURTMFG.COM •NEED ASSISTANCE? •877.287.8 634 •45950-INS-RA •PAGE 2
Step 2 - Determine Required Ball / Hook Height
Determine the proper ball / hook height by leveling the trailer and
measuring from the bottom of the trailer tongue to the ground, see below.
Find the hole closest to that measurement on the adjustable shank (#1).
The pintle mount (#2) will be centered on that hole.
Trailer
Coupler
Rebellion™XD
Level Ground
Drop
Rise
Vehicle
Receiver
Tube
BALL HEIGHT
Step 3 - Attach the Pintle Mount
Based on the determined ball / hook height, slide the pintle mount
onto the shank and align with the proper hole locations.
Angle the pintle mount slightly upwards and press in toward the
shank. Insert a pin (#3) into the top tongue hole first. To pin the
bottom pintle mount hole, apply downward force to the mount, and
slide the second pin into place.
Note: The highest mounting position will require the bottom
pin to be installed first with the mount angled downward.
Then, apply force upwards to install the second pin.
Secure all pins with the clips included with your Rebellion™XD.
WARNING
The pins included with your Rebellion™XD shank are specifically
engineered for this system. If replacement pins are needed, they
must be replaced with original factory mount pins (CURT# 45959).
Before you Begin
The Rebellion™XD pintle mount accessory has a built-in anti-rattle feature
located in the channel on the backside to keep your towing system quiet.
See the recommended assembly instructions for optimal performance.
Step 1 - Insert into the Trailer Hitch
Begin by installing the shank (sold separately) into the trailer hitch
receiver and secure it with a hitch pin and clip (sold separately).
Step 4 - Install the Pintle Hook
Install the pintle hook with the supplied
1/2" hardware and torque to 75 lb-ft.
ASSEMBLY & SETUP
Parts List
Item Qty Description
1 1 Adjustable shank*
2 1 Pintle mount
3 2 Pin*
4 2 Clip*
5 4 Hex bolt
6 4 Lock washer
*Sold separately
1
25-6 3
4