curt 11291 User manual

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing LLC. may repair or replace
the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement
of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
MAKE: STYLE:
MIN.20
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
WEIGHT CARRYING:
INSTALLATION TIPS: INSTALLATION TIME:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY: MODERATE
EASY MODERATE CHALLENGING
THE INSTALL TIME LISTED IS FOR PROFESSIONAL
INSTALLERS. IF YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
INSTRUCTIONS THOROUGHLY.
2. TO EASE INSTALLATION, 2 PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL AND REDUCE THE
TIME REQUIRED.
. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 800.798.0813
Safe y glasses should be
worn a all imes while
ins alling his produc
.
YEARS: 2012-PRESENT SCION MODEL: iQ COMPACT
1,000
150
TRAILER WEIGHT:
TONGUE WEIGHT:
11291 INSTALLATION INSTRUCTIONS
LBS.
LBS.
3/22/2013
WARNING:
WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER
(WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT
WWW.CURTMFG.COM FOR FURTHER INFORMATION.
DIE GRINDER
RATCHET
SAFETY
GLASSES
SOCKET
9/16"
11/16"
SOCKET
EXTENSION
6"
TORQUE
WRENCH
- HOLE ENLARGEMENT
- FISHWIRE HARDWARE

HOLE ENLARGEMENT DIAGRAM
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
Parts List
DESCRIPTIONPART NUMBERQTYITEM
HEX FLANGE NUT7/16-14
21
HEX BOLT3/8-16 X 1 1/242
WASHER3/8"43
CARRIAGE BOLT7/16-14 x 1 1/224
.250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP725
7/16" FISHWIRE7_16 FISHWIRE
26
HEX FLANGE NUTHFN381647
EURO MOUNT OPTION AVAILABLE
#45571 (1-7/8") AND #45572 (2" BALL)
DESIGNED FOR USE WITH
BALLMOUNT # D-55001 / 45501
1
3
2
6
4
5
7
1. Enlarge existing hole to allow 7/16" carriage bolts and
SP7 spacers to pass through, both sides.
ENLARGED ACCESS HOLE
NOTE: ENLARGE EXISTING
HOLE TOWARDS OUTSIDE
OF FRAME RAIL.
EXISTING
HOLE
2. Reverse fishwire 7/16" carriage bolts and SP7 spacers
through enlarged access holes, both sides.

INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
3. Raise hitch into position and loosely secure to carriage
bolts using 7/16" hex flange nuts. Note: The side plates
will slide between the inside of the tow loops.
4. Align holes in side plates with holes in tow loops and
secure using 3/8" hex bolts, 3/8" washers and 3/8" hex
flange nuts, as shown.
5. Torque all 7/16" hardware to 70 ft-lbs.
Torque all 3/8" hardware to 45 ft-lbs.

HOLE ENLARGEMENT DIAGRAM
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
1,000 150
22
20
SCION iQ
3/22/2013
11291
40
Parts List
DESCRIPTIONPART NUMBERQTYITEM
HEX FLANGE NUT7/16-1421
HEX BOLT3/8-16 X 1 1/242
WASHER3/8"
4
3
CARRIAGE BOLT7/16-14 x 1 1/224
.250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP7
25
7/16" FISHWIRE7_16 FISHWIRE
26
HEX FLANGE NUTHFN381647
ENLARGED ACCESS HOLE
ENLARGED
ACCESS HOLE
EXISTING HOLES
(BOTH SIDES)
EXISTING HOLE
ENLARGED ACCESS HOLE
NOTE: ENLARGE EXISTING HOLE
TOWARDS OUTSIDE OF FRAME RAIL
TOW LOOP
(BOTH SIDES)
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
- HOLE ENLARGEMENT
- FISHWIRE HARDWARE
1. Enlarge existing hole to allow 7/16" carriage bolts and SP7 spacers to pass through, both sides.
See Hole Enlargement Diagram.
2. Reverse fishwire 7/16" carriage bolts and SP7 spacers through enlarged access holes, both sides.
See Reverse Pull Fishwire Technique
3. Raise hitch into position and loosely secure to carriage bolts using 7/16" hex flange nuts.
Note: The side plates will slide between the inside of the tow loops.
4. Align holes in side plates with holes in tow loops and secure using 3/8" hex bolts, 3/8" washers
and 3/8" hex flange nuts, as shown.
5. Torque all 7/16" hardware to 70 ft-lbs.
Torque all 3/8" hardware to 45 ft-lbs.
2
1
7
4
5
TOOLS REQUIRED
RATCHET
TORQUE WRENCH
6" EXTENSION
DIE GRINDER
9/16" SOCKET
11/16" SOCKET
SAFETY GLASSES
EURO MOUNT OPTION AVAILABLE
#45571 (1-7/8") AND #45572 (2" BALL)
DESIGNED FOR USE WITH
BALLMOUNT # D-55001 / 45501
3
6