Curtis RSTB User manual

G3 Digital Sweet Tea Brewing System
with Rotating Brew Basket
USER GUIDE
READ AND SAVE THESE INSTRUCTIONS
NOTICE TO INSTALLER: Please leave this booklet with the machine.
øøøøøøøø $
'$345#'30/5$07&3 'SFW$

CONTENTS CL14
.H\)HDWXUHV6SHFLÀFDWLRQV6\VWHP5HTXLUHPHQWV..............................................................................................FS14
,PSRUWDQW6DIHJXDUGV............................................................................................................................................... IS2
,QVWDOODWLRQ,QVWUXFWLRQV*HQHUDO.............................................................................................................................. II2
,QVWDOODWLRQ,QVWUXFWLRQV/HYHOLQJ6ZHHWHQHU:DWHU6XSSO\(OHFWULFDO.................................................................. II8
2SHUDWLQJ,QVWUXFWLRQV%UHZLQJ..............................................................................................................................OI9
2SHUDWLQJ,QVWUXFWLRQV6ZHHWHQHU&RQQHFWLRQ5HSODFHPHQW ..............................................................................OI14
&OHDQLQJ,QVWUXFWLRQV%UHZHU .................................................................................................................................CI1
&OHDQLQJ,QVWUXFWLRQV6ZHHW7HD0L[LQJ6\VWHP...................................................................................................CI8
&OHDQLQJ,QVWUXFWLRQV7HD'LVSHQVHU .....................................................................................................................CI6
3URJUDPPLQJ*XLGH ............................................................................................................................................... 3*
5RXJK,Q'UDZLQJ................................................................................................................................................. 5'
,OOXVWUDWHG3DUWV5HFRPPHQGHG3DUWV0DLQ&KDVVLV........................................................................................... IP14
,OOXVWUDWHG3DUWV5HFRPPHQGHG3DUWV7DQN$VVHPEO\'RPHVWLF....................................................................... IP21
,OOXVWUDWHG3DUWV5HFRPPHQGHG3DUWV7DQN$VVHPEO\([SRUW ........................................................................... IP23
(OHFWULFDO6FKHPDWLF'RPHVWLF............................................................................................................................(6
(OHFWULFDO6FKHPDWLF([SRUW ..............................................................................................................................ES114
7URXEOHVKRRWLQJ*XLGH*HQHUDO............................................................................................................................7*
7URXEOHVKRRWLQJ*XLGH7ULDF6\VWHP....................................................................................................................7*
7URXEOHVKRRWLQJ*XLGH6ZHHWHQHU6\VWHP.........................................................................................................7*
(UURU&RGHV .............................................................................................................................................................EC4
3URGXFW:DUUDQW\....................................................................................................................................................3:
345#$0/5&/54-*45ø 113018B
Contact Information
Wilbur Curtis Co., Inc.
6913 Acco Street | Montebello, CA 90640 US
Phone: [phone] | Toll Free: 800-421-6150
Email: [email protected] | Web: www.wilburcurtis.com
'PSUIFMBUFTUTQFDJmDBUJPOTBOEJOGPSNBUJPOHPUPXXXXJMCVSDVSUJTDPN
5PMM'SFF].POEBZ'SJEBZA.M.- 4:00 P.M.PT
Email: [email protected]
%VFUPDPOUJOVFEQSPEVDUJNQSPWFNFOUUIFQSPEVDUTJMMVTUSBUFEQIPUPHSBQIFEJOUIJTHVJEFNBZWBSZTMJHIUMZGSPNUIFBDUVBMQSPEVDU

KEY FEATURES/SPECIFICATIONS/SYSTEM REQUIREMENTS FS14
Key Features
• (%JHJUBM$POUSPM.PEVMFo1SPWJEFTQSFDJTFDPOUSPMGPSHPVSNFUmOFUVOJOHXJUIQVMTFCSFXJOHEFMBZBOEBMM
DSJUJDBMCSFXJOHGVODUJPO
• (&OIBODFE5FB'MBWPSBOE$MBSJUZo8JUIEJHJUBMBDDVSBDZUXPTFQBSBUFQSFDJTJPOWBMWFTQSPWJEF
VOTVSQBTTFEDPOUSPMPWFSDPODFOUSBUFCSFXJOHBOEEJMVUJPODZDMFT
• i'BTU#SFXw0QUJPOo1SPHSBNTFMFDUBCMF4IPSUFOTCSFXUJNFCZBMMPXJOHDPODFOUSBUFBOEEJMVUJPODZDMFTUP
SVOBUUIFTBNFUJNF
• *OUVJUJWF4DSPMM5ISPVHI1SFDJTJPO1SPHSBNNJOHo-BSHFCSJHIUMZMJHIUFEEJTQMBZDPNNVOJDBUFTGVODUJPOTBUB
HMBODF&BTJMZBEKVTUUJNFWPMVNFUFNQFSBUVSFCSFXGVODUJPOTBOENPSF
• $PME8BUFS#SFX-PDL0VUo1SFWFOUTCSFXJOHXIFOXBUFSUFNQFSBUVSFJTCFMPXTFUMFWFM
6SHFLÀFDWLRQV
(OHFWULFDO6XSSO\5HTXLUHPHQWV
MODEL # DESCRIPTION PHASE VOLTS AMPS HEATING CONFIG WIRE WATTS HERTZ CAPACITY
RSTB Sweet Tea Brewing System
with Rotating Brew Basket 1 PH 120 V 13.8 A 1 X 1600 W 2W + G 1650 W 50/60 Hz 12.0 gal/hr [45.4 l/hr]
RSTBA10000-001 Sweet Tea Brewing System
with Rotating Brew Basket, Two Batch 1 PH 120 V 13.8 A 1 X 1600 W 2W + G 1650 W 50/60 Hz 12.0 gal/hr [45.4 l/hr]
RSTB3 Sweet Tea Brewing System
with Rotating Brew Basket, Export 1 PH 230 V 12.4 A 1 X 2500 W 2W + G 2842 W 50/60 Hz 15.0 gal/hr [56.8 l/hr]
'LPHQVLRQV :DWHU6XSSO\5HTXLUHPHQWV
MODEL # HEIGHT WIDTH DEPTH SHIP WEIGHT SHIP CUBE WATER CONNECTOR WATER PRESSURE MIN. FLOW RATE
RSTB
RSTBA10000-001
RSTB3
34.20”
[86.9 cm]
13.16”
[33.4 cm]
22.96”
[58.3 cm]
41.0 lbs
[18.6 kg]
9.14 cu. ft.
[0.26 m3]µÁDUH
20 - 90 psi
[138 - 620 kPa]
1.0 gpm
[3.8 lpm]
345#,&:'&"563&441&$44:45&.3&26*3&.&/54 $
• #SFX5FNQFSBUVSF¡'¡$
• .JOJNVN#SFX5FNQFSBUVSF¡'¡$
• #SFX7PMVNF-BSHF4NBMM
• &OFSHZ4BWF.PEF0GG
'PMMPXJOHBSFUIFGBDUPSZEFGBVMUTFUUJOHTGPSUIFCSFXFS

IMPORTANT SAFEGUARDS IS2
Symbols
This is the safety alert symbol. It is used to alert you to potential physical injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury or death.
DANGER - Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING - Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION - Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE - Indicates a situation which, if not avoided, could result in property damage.
IMPORTANT - Provides information and tips for proper operation.
SANITATION REQUIREMENTS
Important Safeguards/Conventions
WARNING:
• Make sure that this appliance is installed and grounded according to the INSTALLATION
*/4536$5*0/4CZRVBMJmFEQFSTPOOFMCFGPSFBUUFNQUJOHUPVTFJU'BJMVSFUPGPMMPXUIF*/45"--"5*0/
INSTRUCTIONS could result in personal injury or void the warranty.
• This appliance is designed for commercial use. Any service other than cleaning and preventive
maintenance should be performed by an authorized Wilbur Curtis service technician.
• 5PSFEVDFUIFSJTLPGmSFPSFMFDUSJDTIPDL%0/05PQFOUIFTFSWJDFQBOFMT5IFSFBSFOPVTFS
serviceable parts inside.
• Keep hands, arms and other items away from hot surfaces of the unit during operation.
• Clean the appliance and any dispensers completelyCFGPSFVTJOHUIFNGPSUIFmSTUUJNFBDDPSEJOHUP
the CLEANING INSTRUCTIONS. Clean them regularly as instructed in the CLEANING INSTRUCTIONS.
• Use this appliance only for its intended use, brewing/dispensing hot and/or cold beverages/water.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
• Avoid spillage onto the power (mains) connector.
$0''&&5&"#3&8&34*.1035"/54"'&(6"3%44:.#0-4 )
WARNING - 5IJTQSPEVDUDBOFYQPTFZPVUPDIFNJDBMTJODMVEJOH"DSZMBNJEFBOE#JTQIFOPM"#1"
which are known to the State of California to cause cancer and birth defects or other reproductive harm.
'PSNPSFJOGPSNBUJPOWJTJUXXX18BSOJOHTDBHPW

IMPORTANT SAFEGUARDS IS2
$0''&&5&"#3&8&34*.1035"/54"'&(6"3%44:.#0-4 )
CE Requirements
• This appliance must be installed in locations where it can be overseen by trained personnel.
• 'PSQSPQFSPQFSBUJPOUIJTBQQMJBODFNVTUCFJOTUBMMFEXIFSFUIFUFNQFSBUVSFJTCFUXFFO¡$UP¡$
• This appliance is not suitable for outdoor use.
• 5IJTBQQMJBODFTIBMMOPUCFUJMUFENPSFUIBO¡GPSTBGFPQFSBUJPO
• "OFMFDUSJDJBONVTUQSPWJEFFMFDUSJDBMTFSWJDFBTTQFDJmFEJODPOGPSNBODFXJUIBMMMPDBMBOEOBUJPOBMDPEFT
'PSTBGFVTFBOBMMQPMFEJTDPOOFDUJPONVTUCFJODPSQPSBUFEJOUPUIFmYFEXJSJOHJOBDDPSEBODFXJUIUIF
XJSJOHSVMFTPVUMJOFEJODMBVTFPG*&$GPSNFFUJOHUIFNJOJNVNFMFDUSJDBMTBGFUZPGUIJTTUBOEBSE
• This appliance must not be cleaned by water jet.
• 5IJTBQQMJBODFDBOCFVTFECZQFSTPOTBHFEGSPNZFBSTBOEBCPWFJGUIFZIBWFCFFOHJWFOTVQFSWJTJPOPS
instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
• ,FFQUIFBQQMJBODFBOEJUTDPSEPVUPGSFBDIPGDIJMESFOBHFEMFTTUIBOZFBST
• "QQMJBODFTDBOCFVTFECZQFSTPOTZFBSTBOEBCPWFXJUISFEVDFEQIZTJDBMTFOTPSZPSNFOUBMDBQBCJMJUJFT
or lack of experience and knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
• $IJMESFOVOEFSUIFBHFPGZFBSTTIPVMECFTVQFSWJTFEUPFOTVSFUIFZEPOPUQMBZXJUIUIFBQQMJBODF
• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel
with a special cord available from the manufacturer or its authorized service personnel in order to avoid a
hazard.
• Machine must not be immersed for cleaning.
• $MFBOJOHBOEVTFSNBJOUFOBODFTIBMMOPUCFNBEFCZDIJMESFOVOMFTTUIFZBSFPMEFSUIBOZFBSTBOE
supervised.
• This appliance is intended to be used in household and similar applications such as:
 oTUBGGLJUDIFOBSFBTJOTIPQTPGmDFTBOEPUIFSXPSLJOHFOWJSPONFOUT
 oCZDMJFOUTJOIPUFMTNPUFMTBOEPUIFSSFTJEFOUJBMUZQFFOWJSPONFOUT
– bed and breakfast type environments.
• This appliance not intended to be used in applications such as:
– farm houses
• Access to the service areas permitted by Authorized Service personnel only.
• 5IF"8FJHIUFETPVOEQSFTTVSFMFWFMJTCFMPXE#"

INSTALLATION INSTRUCTIONS II2
Installation Instructions
Installation Requirements
• A secure surface capable of supporting the weight of the appliance.
• For units without an attached cord set attached or dual voltage units set up for use with 220 - 240 Volts:
"QQSPQSJBUFMZTJ[FE6-MJTUFEHSPVOEJOHUZQFQPXFSDBCMFUPNFFUUIFFMFDUSJDBMTQFDJmDBUJPOTGPSUIF
BQQMJBODF*GZPVIBWFRVFTUJPOTBCPVUUIFDPSSFDUDBCMFTJ[FBOEMFOHUIDPOTVMUBRVBMJmFEJOTUBMMFS*GUIF
appliance will be hard wired to a junction box, the power cable must be long enough so that the unit can be
moved for cleaning underneath.
• "HSPVOEFEFMFDUSJDBMDPOOFDUJPOUPBOFMFDUSJDBMDJSDVJUUIBUNFFUTUIFFMFDUSJDBMTQFDJmDBUJPOTPGUIF
appliance (see SPECIFICATIONS). The circuit must be protected by the appropriate sized circuit breaker. If
you are not certain that the existing circuit meets the requirements for your unit, consult a licensed electrician.
• "XBUFSmMUSBUJPOTZTUFNJTSFRVJSFEUPNBJOUBJOUSPVCMFGSFFPQFSBUJPO8JMCVS$VSUJT$P*ODSFDPNNFOETB
8JMCVS$VSUJTBQQSPWFEXBUFSmMUFS4FFUIF$VSUJT&RVJQNFOU$BUBMPHGPSBGVMMMJOFPG8JMCVS$VSUJTBQQSPWFE
XBUFSmMUFST
• 1PUBCMFXBUFSTVQQMZMJOFDPOOFDUJPOGSPNUIFXBUFSmMUFSDBQBCMFPGTVQQMZJOHUIFNJOJNVNnPXSBUFSFRVJSFE
CZUIFTQFDJmDBUJPOT5IFXBUFSTVQQMZMJOFNVTUCFBCMFUPDPOOFDUUPUIFnBSFmUUJOHPOUIFCBDLPGUIF
VOJU4FFUIFSPECIFICATIONS section for the correct size. The water line should also be capable of being
controlled by a shut off valve. Do not connect the water line to a saddle valve or needle valve.
*&$SFRVJSFTUIFGPMMPXJOHXBUFSDPOOFDUJPO
1A quick disconnect or additional coiled tubing (at least two times the depth of the appliance) is required
so that it can be moved for cleaning underneath.
2 5IJTFRVJQNFOUJTUPCFJOTUBMMFEXJUIBEFRVBUFCBDLnPXQSPUFDUJPOUPDPNQMZXJUIBQQMJDBCMF
federal, state and local codes.
 8BUFSQJQFDPOOFDUJPOTBOEmYUVSFTEJSFDUMZDPOOFDUFEUPBQPUBCMFXBUFSTVQQMZTIBMMCFTJ[FE
installed and maintained in accordance with federal, state and local codes.
WARNING:*OTUBMMBUJPOJTUPCFQFSGPSNFEPOMZCZBRVBMJmFEJOTUBMMFS
WARNING: Improper electrical connection may result in an electric shock hazard or damage the unit. This
appliance must be properly grounded.
NOTICE: DO NOT connect this appliance to a hot water supply. The water inlet valve is not rated for hot
water. Do not exceed the maximum water pressure stated in the SPECIFICATIONS section.
IMPORTANT: Observe all governing codes and ordinances.
#3&8&34=41&$*"-5:%*41&/4&34(&/&3*$*/45"--"5*0/*/4536$5*0/4 F
5IF*OUFSOBUJPOBM1MVNCJOH$PEFPGUIF*OUFSOBUJPOBM$PEF$PVODJMBOEUIF'PPEBOE%SVH"ENJOJTUSBUJPO
'%"'PPE$PEFNBOVBMEJSFDUUIBUUIJTFRVJQNFOUNVTUCFJOTUBMMFEXJUIBEFRVBUFCBDLnPX
QSFWFOUJPOJODPNQMJBODFXJUIGFEFSBMTUBUFBOEMPDBMDPEFT'PSVOJUTJOTUBMMFEPVUTJEFPGUIF64"
make sure that the installation is in compliance with the applicable plumbing/sanitation code for your area.

Installation
Leveling
1 Position the brewer on the countertop. Level it left to
right and front to back by turning the bottom of the
legs.
Connect the Water Supply
2 Flush the water supply line prior to installation to
QVSHFBJSBOEEFCSJTGSPNUIFXBUFSmMUFSBOEUVCJOH
3 $POOFDUUIFXBUFSTVQQMZMJOFUPUIFnBSFmUUJOHPO
the back of the brewer. Leave the water supply valve
closed until the power is connected.
Connect the Brewer Wiring
Brewers With a Power Connector Mounted on the Back
4 Connect a C20 IEC power cord (not supplied)
compatible with the electrical outlet installed in the
GBDJMJUZBOEUIBUNFFUTTQFDJmDBUJPOT
INSTALLATION INSTRUCTIONS II8
DECANTER/DISPENSER BREWERS, INSTALLATION INSTRUCTIONS 081519C
WARNING: Use the leveling legs to level the
brewer only. Do not use them to adjust brewer
height. Do not extend them higher than necessary.
Front
panel
or
Style
varies
Brewers With a Strain Relief Mounted on the Back
5 Remove the front panel.
6 Loosen the strain relief on the back of the brewer.
7 On dual voltage units being operated at 220-240 Volts
(nominal) disconnect the existing power cable from
the terminal block and remove. Disconnect and cap
the jumper wire between the “C” and “N” terminals on
the terminal block.
8 Feed the 220-240 Volt power cable into the brewer.
The brewer may be wired for connection directly to
a junction box or (if local ordinances permit) for use
with a power plug that connects to an electrical outlet
meeting the brewer SPECIFICATIONS.
9 Connect the wires on the power cable to the terminal
block inside the brewer.
10 Tighten the strain relief and replace the front panel.
Terminal
block

Power Up the Brewer
14 Turn on the water supply valve.
15 On units with a power plug, connect it to the appropriate
electrical outlet.
11 If the power cord will be connected directly to the
junction box, connect the power cable wires to the
terminals in the junction box. See the ELECTRICAL
SCHEMATIC for the power supply requirements.
INSTALLATION INSTRUCTIONS II8
DECANTER/DISPENSER BREWERS, INSTALLATION INSTRUCTIONS 081519C
Connect the Brewer Wiring (cont.)
Brewers That Come With A Cord Attached
12 If not already installed, install the appropriate type of
power plug for your locality. Consult local electrical
codes to determine the approved type of power plug
for your region.
WARNING: Connect the power cord only to the
appropriate type and size electrical outlet. If it is not
compatible, either have the cord replaced or have
the electrical outlet upgraded by a licensed
electrician. Do not use an extension cord. Do not
use a power cord/plug that is damaged.
WARNING: Turn off power to the junction box at
the circuit breaker panel before connecting the
power cable to the brewer. Lock out and tag the
circuit breaker.
Power cable from brewer
Connect the Bag-in-Box (BIB) Sweetener -
Units Equipped for Brewing Sweet Tea Only
13 Connect two bag-in-box (BIB) sweeteners to the
brewer sweetener supply hoses as instructed in the
OPERATING INSTRUCTIONS section. Connecting two
bags allows the brewer to continue operating if one
bag runs out. The length of the tubing from the transfer
valve to each bag-in-box connector is should be 1 ft.
(30.5 cm) to 3 ft. (91.4 cm). The total length of tubing
from each bag-in-box connector to the brewer can be
up to 6 ft. (183 cm) under optimal conditions.

Power Up the Brewer (cont.)
16 Make sure that the circuit breaker supplying power to
the unit is on.
17 Turn the toggle switch on the back of the brewer to the
0/QPTJUJPO5IFXBUFSUBOLXJMMTUBSUUPmMM8IJMFUIF
UBOLJTmMMJOHJOTQFDUUIFXBUFSTVQQMZMJOFGPSMFBLT
18 When the water in the tank rises to the correct level, the
heating elements will turn on automatically. Depending
on the incoming water temperature and the electrical
TQFDJmDBUJPOTUIFXBUFSUBOLUZQJDBMMZSFRVJSFTUP
minutes to reach the factory set operating temperature.
When the water has heated, Ready to brew will be
displayed on the LCD screen.
19 Perform a brew cycle of a least 12 oz. (350 ml) to purge
any remaining air from the system. See OPERATING
INSTRUCTIONS. During the initial brew cycle and
XIFOFWFSUIFmMUFSJTSFQMBDFEZPVNBZIFBSUIF
TPVOETPGBJSCFJOHQVSHFEGSPNUIFmMUFSUVCJOHBOE
water tank.
20 *GUIFVOJUJTFRVJQQFEXJUIBIPUXBUFSGBVDFUmMMB
coffee cup with hot water to purge air from the hot water
line.
INSTALLATION INSTRUCTIONS II8
DECANTER/DISPENSER BREWERS, INSTALLATION INSTRUCTIONS 081519C
IMPORTANT: When operating the brewer at
higher elevations, reduce the factory set operating
temperature (204°F/96°C) by 2°F/1°C for each
1000 ft. (300 m) of elevation above 2000 ft.
(600 m). See PROGRAMMING GUIDE.

OPERATING INSTRUCTIONS OI9
Brewing Instructions
G3 ROTATING TEA BREWERS, OPERATING INSTRUCTIONS 082216NC
2 Remove/open the lid from
an empty tea dispenser and
position it on the brew deck.
Center it under the brew
basket.
TEA
DISPENSER
3 *OTFSUBDMFBOQBQFSmMUFSJOUP
the brew basket.
4 Fill with the proper amount of
leaf tea. Level the tea in the
mMUFS
5 4MJEFUIFmMMFECSFXCBTLFU
into the brew rails under
the control panel. Slide it all
the way back until it stops.
Rotate the brew basket to
EJSFDUUIFnPXJOUPUIFMFGUPS
right tea container.
The brewer will brew coffee or tea based on the settings programmed into the universal control module (UCM). To
change the settings, see the PROGRAMMING GUIDE.
1 The brewer should be ON.
$POmSNUIJTBUUIFSFBSUPHHMF
switch. “Ready to brew”
should be on the display.
6 Press the brew button. Brewing
will begin immediately.
WARNING - TO AVOID SCALDING, AVOID SPLASHING. Keep body parts clear of the brewer during
brewing. Do not remove the brew basket while “Brewing” appears on the display.
WARNING - DO NOT refrigerate unused tea overnight for later consumption.
The G3 Tea Brewer is factory preset for optimal performance.

OPERATING INSTRUCTIONS OI14
SWEETENER REPLACEMENT/CONNECTION, OPERATING INSTRUCTIONS 100117A
Sweetener Bag-in-Box BIB Replacement/Connection Instructions
The sweet tea mixing system is designed to provide continuous
operation, provided that two BIBs are always connected. When one
BIB becomes empty, the system automatically switches over to the
other one. Replace empty BIBs immediately to assure continuous
operation.
2 Slide the QCD sideways off
of the BIB spout.
3 Place the new BIB container
on the rack and remove the
cardboard spout cover.
4 Pull off the shipping cap that
covers the spout on the bag.
5 Place the QCD next to the
spout, then slide sideways
until it stops.
The brewer will prime the new bag and begin to use the contents when the other bag runs out of sweetener. If the
hoses are empty (for example on new units), place a container under the brew basket and press the PRIME button
until sweetener comes out of the spout.
1 Release the quick connect/
disconnect connector (QCD)
by pulling up on the hose
and cap assembly on the
opposite side. The plunger
will pop up in the center of
the QCD.
6 Push in on the QCD plunger
until it snaps into place.
Pull plunger out
before removal

NOTICE - Do not use cleaning liquids, compounds or powders containing chlorine (bleach) or corrosives.
5IFTFQSPEVDUTQSPNPUFDPSSPTJPOBOEXJMMEBNBHFUIFmOJTIFT USE OF THESE PRODUCTS WILL VOID
THE WARRANTY.
CLEANING INSTRUCTIONS CI1
Cleaning The Brewer - Daily
BREWERS - GENERIC, CLEANING INSTRUCTIONS 080416B
WARNING: HOT SURFACES - To avoid injury, allow the brewer and dispenser(s) to cool before cleaning.
The brewer should be OFF.5VSOUIFCSFXFSPGGCZnJQQJOHUIFSFBSUPHHMFTXJUDIUPUIF0''QPTJUJPO
1 Remove the dispenser(s). Wipe exterior brewer surfaces with a damp cloth to remove spills and debris.
2 Remove the brew basket(s) and clean them in a mild detergent solution. Use a soft bristled brush for hard to
clean areas. Rinse with clean water, then dry.
3 Wipe the spray head area with a cloth soaked in a mild detergent solution. Rinse with a cloth soaked with
clean water removing any residual detergent. Use a clean, soft cloth to dry.
4 Dump out the drip tray(s) (if applicable). Rinse with clean water, then dry with a soft, clean cloth.
Cleaning The Brewer - Weekly
The brewer should be OFF.5VSOUIFCSFXFSPGGCZnJQQJOHUIFSFBSUPHHMFTXJUDIUPUIF0''QPTJUJPO
1 Remove the spray head(s), unscrewing counterclockwise from the dome plate.
2 Thoroughly clean and rinse the dome plate area.
3 Clean the brew basket rails with a brush soaked with a mild detergent solution. Rinse the area with a cloth
soaked with clean water, removing any residual detergent.
4 Dry the area with a soft, clean cloth.
5 Reattach the spray head(s).
WARNING: DO NOT immerse the brewer in water or any other liquid.

CLEANING INSTRUCTIONS CI8
48&&55&".*9*/(4:45&.(&/&3*$$-&"/*/(*/4536$5*0/4øø "
Sweet Tea Mixing System Cleaning and Sanitizing (Weekly)
Use a concentrated sanitizing-cleaning solution to simplify the cleaning procedure. This procedure requires a
TPMVUJPOPGXBSNXBUFSBOEBHSBOVMBUFEDPODFOUSBUFETBOJUJ[FSDMFBOFSEJMVUFEBTTQFDJmFECZUIFNBOVGBDUVSFS
JOBPOFHBMMPOCVDLFUPGDMFBOXBSNXBUFSNBYJNVN'
 3FNPWFCPUIRVJDLDPOOFDUEJTDPOOFDU2$%
DPOOFDUPSTGSPNUIFTXFFUFOFSCBHJOCPY#*#
QSPEVDUCBHT
 1VMMUIFDBQTPGGPGUIF2$%TBOEJNNFSTFUIFN
in the container containing the sanitizing-cleaning
solution.
3 1MBDFBMBSHFFNQUZDPOUBJOFSPOUIFCSFXEFDL
CFMPXUIFTQSBZIFBE
4 1SFTTUIF13*.&CVUUPOVOUJMTBOJUJ[JOHDMFBOJOH
solution is coming out of the spout instead of
sweetener.
5 1VTIEPXOPSQVMMVQPOUIFLOPCPOUIFUPQ
of the transfer valve until the arrow changes
EJSFDUJPOTFFEJBHSBN1VTIUIF13*.&CVUUPO
VOUJMUIFSFNBJOJOHTXFFUFOFSIBTCFFOQVSHFE
from the hose system.
6 "MMPXUIFCSFXFSUPTJUGPSUIFBNPVOUPGUJNF
TQFDJmFECZUIFTBOJUJ[FSDMFBOFSNBOVGBDUVSFS
XJUIUIFDMFBOJOHTPMVUJPOJOUIFTXFFUFOFSIPTFT
lines.
 'MVTIUIFTZTUFNCZmMMJOHBPOFHBMMPODPOUBJOFS
XJUIDMFBOXBSNXBUFSOPDMFBOJOHTPMVUJPO
1SFTTUIF13*.&CVUUPOVOUJMPOMZDMFBSXBUFS
comes out of the system.
8 1VTIEPXOPSQVMMVQPOUIFLOPCPOUIFUPQ
of the transfer valve until the arrow changes
EJSFDUJPO1VTIUIF13*.&CVUUPOBHBJOVOUJMUIF
SFNBJOJOHDMFBOFSIBTCFFOnVTIFEPVUPGUIF
hose system.
9 3FNPWFUIF2$%TGSPNUIFCVDLFUDPOUBJOJOHUIF
hot water and replace the caps. Reconnect the
2$%TUPUIF#*#QSPEVDUCBHT
 1SFTTUIF13*.&CVUUPOVOUJMTXFFUFOFSJTDPNJOH
out of the dilution spout.
 %JTDBSEUIFTPMVUJPOUIBUIBTQPVSFEJOUPUIF
DPOUBJOFSPOUIFCSFXEFDL
Sanitizing and Cleaning - Steps 1 to 6
Transfer Valve
Rinsing - Steps 7 to 11
To transfer
valve
Dilution
spout
Sweetener
pump
Container
to catch
used
solution
Container
to catch
used
solution
Mix sanitizer-
cleaner in 1 Gal.
of hot water
Hot rinse
water
Cap
QCD
Sweetener
hose assembly
Transfer
valve
Knob

CLEANING INSTRUCTIONS CI6
TEA DISPENSER, CLEANING INSTRUCTIONSø B
Cleaning the Tea Dispenser (Daily)
The following cleaning process requires a mild solution
of dish-washing detergent and warm water, and One-Pro
#FWFSBHF&RVJQNFOU$MFBOFS$VSUJT1/8$.JYUIF
0OF1SPDMFBOFSBUBSBUJPPGP[HQFSHBM-PG
IPUXBUFS¡'¡$NJO
Container
 1SFQBSFBNJMETPMVUJPOPGEFUFSHFOUBOEXBSNXBUFS
Remove the dispenser from the brewer and remove the
MJE3JOTF
 Wash8JQFUIFFYUFSJPSTVSGBDFTXJUIBTQPOHFBOE
UIFEFUFSHFOUTPMVUJPOUPSFNPWFTQJMMTBOEEFCSJT6TF
the detergent solution and a soft bristled brush to wash
UIFJOTJEFPGUIFDPOUBJOFS
3 Rinse3JOTFXJUIDMFBOXBSNXBUFS
4 Sanitize'JMMUIFDPOUBJOFSUPUIFUPQXJUI0OF1SP
DMFBOJOHTPMVUJPONJYFEBTTQFDJmFEBCPWF"MMPX
UIFNJYUVSFUPTPBLGPSNJOVUFTUIFOESBJO'JMMUIF
DPOUBJOFSUPUIFUPQXJUIXBSNDMFBOXBUFSUIFOESBJO'JMM
XJUIXBUFSBOEESBJOBTFDPOEUJNF
 Disassemble the faucet - Unscrew the faucet assembly
GSPNUIFEJTQFOTFS5IFOVOTDSFXUIFIBOEMFCPOOFU
BTTFNCMZGSPNUIFUPQPGUIFGBVDFUBOESFNPWF*OTQFDU
UIFTFBUDVQGPSXFBS3FQMBDFUIFTFBUDVQJGJUJT
EBNBHFE
6 Air Dry - Turn the container upside down and allow to
BJSESZ
Faucet, Lid and Drip Tray
 Wash - Wash the lid, drip tray and faucet parts with the
EFUFSHFOUTPMVUJPO
 Rinse - Thoroughly rinse all parts with clean, warm
XBUFS
 Sanitize - After rinsing, place the faucet parts in One-
1SPTPMVUJPONJYFEBTTQFDJmFEBCPWFBOEBMMPXUIFN
UPTPBLGPSNJOVUFT
 Air Dry3FNPWFUIFQBSUTGSPNUIFTBOJUJ[FSSJOTF
UIFNPGGUIPSPVHIMZBOEBMMPXUIFNUPBJSESZ
 3FBTTFNCMF8IFOESZSFBTTFNCMFUIFIBOEMFCPOOFU
)BOEUJHIUFOUIFIBOEMFCPOOFUPOUPUIFUPQPGUIFGBVDFU
BTTFNCMZ)BOEUJHIUFOUIFGBVDFUBTTFNCMZPOUPUIF
EJTQFOTFSPVUMFU
Seat cup
Faucet
Handle
Bonnet
WASH
RINSE
SANITIZE

With unit OFF, press and hold
bottom right BREW button (4).
Then press and release ON/OFF
button. Continue to hold down
BREW button until Enter Code
appears.
To enter programming mode:
Entering
Programming Mode
Enter Code
- - - -
Curtis
Program Menus
<-- Select -->
continued...
Tea Recipes
<-- Select -->
Tea by Volume
<-- Select -->
Enter 4 digit code.
(factory default = 1-2-3-4)
PROGRAMMING GUIDE PG4
IMPORTANT: All programming functions are performed with the
three center buttons.
The symbols below the buttons are:
 Ż Scroll UP (1)
~SELECT or ENTER to save new parameter (2)
ŹScroll DOWN (3)
Once you enter programming mode, press Żor Źto scroll UP or DOWN
through the various functions/features. Press ~(Select) to make changes
to the function/feature displayed. Then press Żor Źto scroll through
the various available settings. See Programming Options for detailed
descriptions.
Actual label appearance
varies with model
8$130(3"..*/((6*%&ø B
Programming Options
To exit, press Źuntil Exit appears on the display, then press ~.
Tea Recipes - sets the tea recipe. Press ~to access. Press Żor Źto
choose from standard-gray, standard-purple, Standard-Amber, Tropical-
Gray, Tropical-Purple, 76/308-Gray or 76/308-Purple. Press ~to save and
exit programming mode.
Tea by Volume - sets the tea brewing volume. After selecting this feature
(~), press the BREW button for which the brew volume needs to be changed
(SHIFT+BREW selects half batch on some models). Place an empty
container under the (empty) brew basket. Press the same BREW button
again to start. When the desired volume is reached, press the BREW button
BHBJOUPTUPQUIFnPX5IFWPMVNFIBTCFFOTFU1SFTTŹto display the
subsequent menu features.

Programming Options (cont.)
PROGRAMMING GUIDE PG4
8$130(3"..*/((6*%&ø B
continued
continued...
Tea by Time
<-- Select -->
Tea Dilut. Delay
<-- Select -->
Tea Dilut. Volume
<-- Select -->
Tea Dilut. Time
<-- Select -->
Tea Dilut. Stir
<-- Select -->
Tea Pulse Brew
<-- Select -->
Tea by Time - sets the amount of tea brewed according to time. Once accessed (~),
press the BREW button for which the brew time needs to be changed (SHIFT+BREW
selects half batch on some models). Press Żor Źto highlight minutes or seconds.
Press ~to change the setting. The range is 0:00 to 9:59. Once the amount of time
is entered, press ŹVOUJMFYJTnBTIJOHUIFOQSFTT~to save. Press Źto display the
subsequent menu features.
Tea Dilut. Delay - sets the delay until tea dilution begins. Once accessed (~), press
the BREW button for which the dilution delay needs to be changed (SHIFT+BREW
selects half batch on some models). Press Żor Źto increase or decrease time. The
range is 0:30 to 10:00. Press ~to save. Press Źto display the subsequent menu
features.
Tea Dilut. Volume - sets the tea dilution volume. Once accessed (~), press the
BREW button for which the dilution volume needs to be changed (SHIFT+BREW
selects half batch on some models). Place an empty container under the (empty) brew
basket. Press the same BREW button a second time to start. When the desired dilution
WPMVNFJTSFBDIFEQSFTTUIF#3&8CVUUPOBHBJOUPTUPQUIFnPX5IFEJMVUJPOWPMVNF
has been set. Press Źto display the subsequent menu features.
Tea Dilut. Time - sets the amount of tea dilution according to time. Once accessed
(~), press the BREW button for which the dilution time needs to be changed
(SHIFT+BREW selects half batch on some models). Press Żor Źto highlight minutes
or seconds. Press ~to change the setting. The range is 0:00 to 9:59. Once the
amount of time is entered, press ŹVOUJMFYJTnBTIJOHUIFOQSFTT~to save. Press Ź
to display the subsequent menu features.
Tea Dilut. Stir - turns the dilution stir feature On and Off. Once accessed (~), press
the BREW button for which stir needs to be turned On or Off (SHIFT-BREW selects
half batch on some models). Press Żor Źto toggle between On and Off. Press ~to
save. Press Źto display the subsequent menu features.
Tea Pulse Brew - turns pulse brew On and Off and adjusts the pulse brew settings
when set to On. Once accessed (~), press the BREW button for which pulse needs
to be turned On or Off (SHIFT+BREW selects half batch on some models). Press ~to
save. If On is selected, subsequent screens will appear to adjust the Pulse Count, On
Time and Off Time. Press Żor Źto select the setting for each screen, then press ~
to move to the next screen. Press Źto display the subsequent menu features.

PROGRAMMING GUIDE PG4
Programming Options (cont.)
8$130(3"..*/((6*%&ø B
continued
continued...
Tea Half Batch
<-- Select -->
Tea Fast Brew
<-- Select -->
Sweetener Time
<-- Select -->
Sweetener Delay
<-- Select -->
Swtnr-Dil Pulse
<-- Select -->
Tea Drip-Out
<-- Select -->
Tea Fast Brew - turns fast brew On and Off and adjusts the Delay Time when set
to On. Once accessed (~), press the BREW button for which fast brew needs to be
turned On or Off (SHIFT+BREW selects half batch on some models). Press Żor Źto
toggle between On and Off, then ~to save. If On is selected, the Delay Time screen
will appear. Press Żor Źto change the setting, then ~to save. Press Źto display
the subsequent menu features.
Tea Half Batch - turns half batch On and Off. Once accessed (~), press Żor Ź
to toggle between On and Off. Press ~to save. Press Źto display the subsequent
menu features.
Tea Drip-Out - sets the Tea Drip-Out time. Drip-out allows additional time for tea
to drain from the brew basket before “Brewing” disappears from the display. Once
accessed (~), press the BREW button for which the drip-out feature needs to be
changed (SHIFT+BREW selects half batch on some models). Press Żor Źto
change the drip-out time. The range is Off to 15:00. Press ~to save. Press Źto
display the subsequent menu features.
Sweetener Time (units equipped for brewing sweet tea only) - adjusts the amount
of time sweetener is dispensed when brewing sweet tea. Once accessed (~), press
the BREW button for which the sweetener time needs to be changed (SHIFT+BREW
selects half batch on some models). Press Żor Źto highlight minutes or seconds.
Press ~to change the setting. The range is 0:00 to 9:59. Once the amount of time
is entered, press ŹVOUJMFYJTnBTIJOHUIFOQSFTT~to save. Press Źto display the
subsequent menu features.
Sweetener Delay (units equipped for brewing sweet tea only) - sets the delay until
sweetener begins pour. Once accessed (~), press the BREW button for which the
sweetener delay needs to be changed. (SHIFT+BREW selects half batch on some
models). Press Żor Źto increase or decrease time. The range is Off to 10:00. Press
~to save. Press Źto display the subsequent menu features.
Swtnr-Dil Pulse (units equipped for brewing sweet tea only) - turns the Sweetener
Dilution Pulse On and Off. Once accessed (~), press the BREW button for which
dilution pulse needs to be turned On or Off. Press Żor Źto toggle between On and
Off. Press ~to save. Press Źto display the subsequent menu features.
1Models TEA/IC-1BATCH, TEA/IC-2BATCH, TEA/IC-3BATCH, TEA/IC- 4BATCH, DUAL-DILUTION,
TEA-SWEET, DUAL-SWEET and COMBO only.
2Models TEA SWEET, DUAL-SWEET and COMBO-SWEET. only.
1
2
2
2

Coffee Pre-Infusn (combo units only) - sets the brewer Coffee Pre-Infusion time
(Pulse Brew must be Off to access). Pre-Infusion increases control of coffee clarity and
extraction. Once accessed (~), press the BREW button for which pre-infusion needs
to be changed. Press Żor Źto change the setting. The range is Off to 60 seconds.
Press ~to save. Press Źto display the subsequent menu features.
When Coffee Pre-Infusion is On, Coffee Pulse Brew is disabled.
Programming Options (cont.)
PROGRAMMING GUIDE PG4
8$130(3"..*/((6*%&ø B
Setting Description
A Starts at beginning of brew cycle. 4 cycles of 10 seconds on and 5 seconds off, then on until end of brew cycle.
B Starts towards end of brew cycle. 4 cycles of 5 seconds off and 4 cycles of 10 seconds on. Ends when brew cycle ends.
C Starts at beginning of brew cycle. 5 cycles of 25 seconds on and 10 seconds off, then on until end of brew cycle.
DManually set. Starts at beginning of brew cycle. Number of pulses is adjustable from 1 to 20. Pulse on time and off time are
both adjustable from 5 to 150 seconds, in 5 second increments.
EManually set. Starts at beginning of brew cycle. Number of pulses is adjustable from 1 to 8. Pulse on time and off time are
both adjustable from 1 to 150 seconds.
continued...
continued...
Coffee Pulse Brew
<-- Select -->
Coffee Pre-Infusn
<-- Select -->
Coffee by Volume
<-- Select -->
Coffee by Time
<-- Select -->
Coffee by Volume (combo units only) - sets coffee brewing volume. Once
accessed (~), press the BREW button for which the brew volume needs to be changed
(SHIFT+BREW selects half batch on some models). Place an empty container under
the (empty) brew basket. Press the same BREW button again to start. When the
EFTJSFEWPMVNFJTSFBDIFEQSFTTUIF#3&8CVUUPOBHBJOUPTUPQUIFnPX5IFWPMVNF
has been set. Press Źto display the subsequent menu features.
Coffee by Time (combo units only) - sets the amount of coffee brewed according to
time. Once accessed (~), press the BREW button for which the brew time needs to be
changed (SHIFT+BREW selects half batch on some models). Press Żor Źto highlight
minutes or seconds. Press ~to change the setting. The range is 0:00 to 9:59. Once the
amount of time is entered, press ŹVOUJMFYJTnBTIJOHUIFOQSFTT~to save. Press Ź
to display the subsequent menu features.
Coffee Pulse Brew (combo units only) - selects the Coffee Pulse Brew pattern (Pre-
Infusion must be Off to access). The pulse brew pattern selected “tunes” or changes
UIFnBWPSPGUIFDPGGFF0ODFBDDFTTFE~), press the BREW button for which Pulse
Brew needs to be changed. Press Żor Źto select the desired setting (see guidelines
below for information on various settings). Press ~to save. Press Źto display the
subsequent menu features.
When Coffee Pulse Brew is on, Pre-Infuson is disabled.
continued...
3
3
3
3
3 Models COMBO, COMBO/IC and COMBO-SWEET only.

PROGRAMMING GUIDE PG4
Pulse Brew Guidelines
• Filter pack type coffees typically extract better with the A and B pulse setting.
• Decaffeinated coffees typically extract better with the B pulse setting.
• High-yield coffees typically extract better with the C pulse setting. Of course,
BOZPGUIF"#PS$TFUUJOHTNBZCFVTFEUPTVJUZPVSUBTUFQSPmMF
• Settings D and E are manual pulse counts.
8$130(3"..*/((6*%&ø B
continued
continued...
Safety Sw On/Off
<-- Select -->
Energy Save Mode
<-- Select -->
Brew Count Odom
<-- Select -->
Brew Count Total
<-- Select -->
Temperature
<-- Select -->
Coffee Drip-Out
<-- Select -->
Coffee Drip-Out (combo units only) - sets the Coffee Drip-Out time. Drip-out allows
additional time for coffee to drain from the brew basket before “Brewing” disappears
from the display. Once accessed (~), press the BREW button for which the Drip-Out
time needs to be changed (SHIFT+BREW selects half batch on some models). Press
Żor Źto increase or decrease time. The range is Off to 5:00. Press ~to save. Press
Źto display the subsequent menu features.
Safety Sw On/Off (combo units only) - turns the feature On and Off. Once accessed
(~), press Żor Źto toggle between On and Off. Press ~to save. Press Źto display
the subsequent menu features.
Temperature - adjusts the maximum tank water temperature. Once accessed (~),
press Żor Źto increase or decrease the temperature. The setting range is 170ºF
to 208ºF (77ºC to 98ºC). Press ~to save. Press Źto display the subsequent menu
features.
Energy Save Mode - saves energy during periods when the brewer is not in use.
When set to On, the brewer automatically shuts off four hours after the last brew
cycle. Press the ON/OFF button to return to normal operation. When set to On-140ºF
(60ºC), the brewer shuts off four hours after the last brew cycle, but the water tank
temperature remains at 140ºF. Use the On-140ºF setting to reach brewing temperature
faster after periods of non-use. Once accessed (~), press Żor Źto choose the
desired setting. Press ~to save. Press Źto display the subsequent menu features.
Brew Count Odom - When accessed, this feature displays the total brew cycles
since the odometer was last reset. Press Źto go back without resetting or ~to reset.
Press Źto display the subsequent menu features.
Brew Count Total - when accessed (~), displays the total brew cycles on the brewer.
It cannot be reset. The display returns to the previous screen automatically after a few
seconds. Press Źto display the subsequent menu features.
3
3
3 Models COMBO, COMBO/IC and COMBO-SWEET only.
continued...

PROGRAMMING GUIDE PG4
8$130(3"..*/((6*%&ø B
Programming Options (cont.) continued
continued...
Master Reset
<-- Select -->
Cold Brew Lock
<-- Select -->
Access Code
<-- Select -->
Banner Name
<-- Select -->
Service Call
<-- Select -->
P-Maintenance
<-- Select -->
Cold Brew Lock - adjusts the temperature at which the brewer will brew when a
BREW button is pressed (Ready to brew appears on the display). This feature also
adjusts the temperature at which the heating element turns on to reheat the water
in the tank. The available settings are 5°F/3°C, 15°F/8°C (below the water tank
temperature settings) and Off. Off is within 30°F/17°C below the tank temperature
setting. Once accessed (~), press Żor Źto select the desired setting. Press ~to
save. Press Źto display the subsequent menu features.
Master Reset - resets the brewer universal control module (UCM) to the factory
default settings. Once accessed (~), “Are You Sure?” will appear on the display. Press
Żfor Yes or Źfor No. If you press No, the display goes back to the programming
menu. If you press Yes, the UCM will reset and exit programming mode.
Service Call - sets the service phone number that appears on the display when the
UCM detects a SENSOR ERROR or WATER ERROR. Once accessed (~), press Ż
or Źto select the number to be changed. Press ~repeatedly to change the number
value. Press Żor Źto select the next number to change. When done, press Ź
VOUJMFYnBTIFTPOUIFEJTQMBZBOEQSFTT~. Press Źto display the subsequent menu
features.
Access Code - sets the access code entered to access programming mode (the
factory default is 1-2-3-4). Once accessed (~), press Żor Źto select the number to
be changed. Press ~repeatedly to change the number value. Press Żor Źto select
the next number to change. When done, press ŹVOUJMFYnBTIFTPOUIFEJTQMBZBOE
press ~. Press Źto display the subsequent menu features.
Banner Name - changes the banner name that appears on the display. No banner
name appears when all blanks are entered. Once accessed (~), press Żor Źto
select the letter to change. Press ~repeatedly to change the letter. When done, press
ŹVOUJMFYnBTIFTPOUIFEJTQMBZBOEQSFTT~. Press Źto display the subsequent
menu features.
P-Maintenance - adjusts the P-Maintenance (preventive maintenance) brew monitor.
When on, the UCM measures the number of gallons brewed before the P-Maintenance
reminder appears on the display. The range is Off to 3000 gallons (11,000 liters).
Once accessed (~), press Żor Źto select the desired setting, then press ~to save.
Press Źto display the subsequent menu features.
continued...