Curtis Shg Instruction Manual

Installation Instructions,

Service & Warranty Information

Revised: Oct 2001

MODELS INCLUDEDMODELS INCLUDED

MODELS INCLUDED

••

• SHG

••

• DHG

FIND OUT MORE

ON THE WEB.

WILBURCURTIS.COM

WILBUR CURTIS COMPANY Montebello, CA 90640

DRAFT COPY

NotReleased.ThisVersionExistsasFileNo.

I:\DIAGRAMS\FRANK\FX-134.p65

CURTISCOFFEEGRINDERS

FOR THE LATEST SPEC INFORMATION GO TO WWW.WILBURCURTIS.COM

•

ISO9001REGISTERED

SHGGrinder

DHGGrinder

ImportantSafeguards/Conventions

WILBURCURTISCOMPANY

Montebello,CA90640

CAUTION:CAUTION:

CAUTION: Please

use this setup

procedure before

attempting to use this grinder.

Failure to follow the instructions

can result in injury or the voiding

of the warranty.

WARNING TO AVOID

SCALDING, Do not

remove brewcone whil

brew light is flashing.

ISO9001REGISTERED

Installation Instructions, Service & Warranty Information

FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO

WWW.WILBURCURTIS.COM

This appliance is designed for commercial use.Any servicing other than cleaning and maintenance should be performed by an

authorized Wilbur Curtis service center.

• Do NOT immerse the unit in water or any other liquid

• To reduce the risk of fire or electric shock, do NOT open top panel. No user serviceable parts inside.Repair should be done

only by authorized service personnel.

• Keep hands and other items away from hot parts of unit during operation.

• Never clean with scouring powders or harsh implements.

ConventionsConventions

Conventions

WARNINGS –ARNINGS –

ARNINGS –ARNINGS –

ARNINGS – TT

To help ao help a

o help ao help a

o help avoid personal injurvoid personal injur

void personal injurvoid personal injur

void personal injuryy

yImportant Notes/Cautions – from the factorImportant Notes/Cautions – from the factor

Important Notes/Cautions – from the factorImportant Notes/Cautions – from the factor

Important Notes/Cautions – from the factoryy

QUICK STQUICK ST

QUICK STARAR

ARAR

ART & SETUPT & SETUP

T & SETUPT & SETUP

T & SETUP

SETUPSETUP

SETUP

1. Install the grinder on a firm, level base in a location where it can be connected to a grounded electrical outlet of 120VAC,

rated at 15 amps minimum.

2. Test the unit by running some whole bean coffee through the grinder. If any problems are encountered, refer to the

troubleshooting section complete at www.wilburcurtis.com or call Technical Service at 800-995-0417.

OPERAOPERA

OPERATING INSTRTING INSTR

TING INSTRTING INSTR

TING INSTRUCTIONSUCTIONS

UCTIONSUCTIONS

UCTIONS

1.1.

1. Open the door on top of the grinder and fill with fresh whole bean coffee.

Close the top door.

WILBURILBUR

ILBURILBUR

ILBUR CC

CURTISURTIS

URTISURTIS

URTIS CC

COMPOMP

OMPOMP

OMPANYANY

ANYANY

ANY, I, I

, I, I

, INCNC

NCNC

NC..

211

544

433

877

1010

ModelsIncluded

SHG

DHG

ADJUSTING THE GRINDSADJUSTING THE GRINDS

ADJUSTING THE GRINDS

1. Empty hopper of coffee beans. Run grinder to clear grinding burrs of coffee.

2. Open housing cover to locate adjustment screw (8) and lock nut (7). Loosen lock nut.

3. Run motor during adjustment. Turning adjustment screw clockwise will result in a finer

grind (if, while turning, you hear the grinding burrs starting to touch, immediately, back

off 1/8th turn). Turning counter clockwise will produce a coarser grind.

4. With a screwdriver holding the adjustment screw in place, tighten the locknut.

5. Run some coffee beans through the machine to check the grind adjustment.

6. Replace front cover on machine.

*This adjustment may change the amount of ground coffee dispensed.

CHANGING A BROKEN SHEAR DISKCHANGING A BROKEN SHEAR DISK

CHANGING A BROKEN SHEAR DISK

1. Unplug the power cord.

2. Empty the hopper of beans.

3. Take out the thumb screws (10) to remove the grind cap (6).

4. Pull out the grinding burr/feed worm assembly (2). The inner half of the grinding burr set

will remain in the housing.

5. Separate the shear cap (5) and shear drive (3). The snapped shear disk (4) should fall

out of it’s slot on the shear drive.

6. Inspect and clean housing (1) of any coffee or debris. Especially look for anything that may have broken the shear disk.

7. Re-insert the feed worm and grinding burr on to the motor shaft.

8. Push shear drive through burr/feed worm assembly and align large slot with tongue on the motor shaft.

9. Rotate burr/feed worm assembly to align slot with narrow slot on shear drive.

10. Insert a new shear disk into slot. Cover with the shear cap.

11.Replace grind cap and thumb screws.

2.2.

2. Place a new paper filter into the brewcone.

3.3.

3. Insert the brewcone into the basket holder arms on the grinder.

4.4.

4. Press the grind switch. Allow the grind motor to completely stop before removing

the brewcone.

5.Transfer the filled brewcone to the brewer and press the desired brew

button. Brew cycle is complete when the brew light stops flashing.

FINDIND

INDIND

IND

OUTOUT

OUT

MOREMORE

ONON

THETHE

THE

WEBWEB

WEB.....

WILBURWILBUR

WILBURCURCUR

CURCUR

CURTIS.COMTIS.COM

TIS.COMTIS.COM

TIS.COM

TIMER SETTING – DHGTIMER SETTING – DHG

TIMER SETTING – DHG

1.3

1.5

1.8

2.0

2.5

3.0

3.7

4.5

6.2

7.6

8.8

10.0

11.8

13.5

1. To set the timer, press PROGRAM/SAVE button on timer (switches on front cover will begin flashing).

2. Select one of the switches on the front cover, REGULAR or DECAF, and press.

3. The lighted digital display on the timer will show the present time setting on this switch.

4. Press the UP or DOWN button to change the amount of seconds you want to add or subtract from the switch you choose.

5. Press the PROGRAM/SAVE button again to set time.

6. Repeat steps 1 to 5 for each switch

NOTE:NOTE:

NOTE: Time settings in

this table are only

approximate. Amounts

will vary with grind texture and

specific coffee bean. Weigh your

output, then make adjustments as

necessary

ILLUSTRAILLUSTRA

ILLUSTRATED PTED P

TED PTED P

TED PARAR

ARAR

ARTSTS

TSTS

LISTLIST

LIST

GRINDERMOTOR

Seconds OuncesSeconds Ounces

PARTS

DIAGRAMS SHG Hopper & CoversSHG Hopper & Covers

SHG Hopper & CoversSHG Hopper & Covers

SHG Hopper & Covers

1919

3434

2121

2222

MOTOR, GRINDER 120VAC

CAPACITOR, COFFEE GRINDER ASSY

SHEAR DRIVE COFFEE GRINDER

SHEAR DISK

CAP,SHEAR DISK GRINDERS

COVER,GRINDER HOUSING W/LABEL

SCREW & THRUST PIN ADJUSTING ASSY

SPRINGBAFFLE LONG, NITRIC ACID COLORING

SPRING BAFFLE SHORT, NITRICACID COLORING

BAFFLE, SPOUT

SPOUT,GRINDERHOUSING

BURRS, SET CRUSH HIGH FLOW

SPRING, TENSION COFFEE GRINDER

WORM FEEDING ASSY CCG

WC-91022

WC-91026

WC-91024

WC-91025

WC-91016

WC-91017

WC-91015

WC-91029

WC-91027

WC-91028

WC-91023

WC-91045

WC-91021

WC-91020

DESCRIPTIONITEM PARTN°

ItemItem

Item Part No.Part No.

Part No.Part No.

Part No. DescriptionDescription

DescriptionDescription

Description

Hopper & Top CoverHopper & Top Cover

Hopper & Top Cover

DHG OnlyDHG Only

DHG Only

PARTS

DIAGRAMS

COVER, TOP ASSEMBLY

HOPPER, COFFEE BEAN SHG

COVER,FRONTSHG

LABEL, SHG

TOP COVER, DUAL HOPPER

ACRYLIC GLASS WINDOW

SPACER, 5/16 x 1/2 x 5/8 (OPTIONAL)

STAR WHEEL (OPTIONAL)

SPACER, 5/16 x 1/2 x 9/32 (OPTIONAL)

DIVIDER, DUAL HOPPER SS DHG, ILGD (OPTIONAL)

DIVIDER, W/HOLE ILG-11/DHG-11

SHAFT FOR STAR WHEEL (OPTIONAL)

HOPPER,DUAL

AUGERANCHOR

BEARING,AUGER

DRIVE FOR AUGER

WRAP, HOPPER ASSY DHG, ILG

PANEL, TOP BACK

FUNNEL, DUAL HOPPER

CAP SEAL, S/S

GEARMOTOR

CIRCUIT BREAKER, 10A

COVER ASSEMBLY, SPOUT & ARM

SWITCH, DECAF, 115V (H/W)

SWITCH, REGULAR COFFEE (BRW)

LABEL, FRONT SWITCH

MOTOR, 1/2 HP, 120V, 1725 RPM

TIMER, DIGITAL DHG 115-230VAC INPUT

TIMER, 120V .5-60 SEC SHG-10

BASE, STAINLESS STEEL

BUMPER LEG, 8-32 THREAD

BASKET HOLDER

SPRING, BASKET HOLDER

NUT, HEX,5/8 X 11/16 LONG

SCREW, 5/16 x 5/8 LONG SHOULDER

WC-9129

WC-9117

WC-9165

WC-3891

WC-9118

WC-9131

WC-9143

WC-9160

WC-9144

WC-9132

WC-9188

WC-9142

WC-9116

WC-9158

WC-9183

WC-9157

WC-9161

WC-9146

WC-9130

WC-9134

WC-9151

WC-1504

WC-9164

WC- 124

WC- 122

WC-3892

WC-9135

WC- 635

WC- 628

WC-9101

WC-3502

WC-9141

WC-9155

WC-9123

WC-4813

10A

27A

1616

1212

1010

1111

1313

131414

1414

1717

2424

24 2525

2525

2323

1919

2020

1919

1818

27A27A

27A

2929

2828

3232

3030

3131

2626

2727

3333

Center Cover & GearCenter Cover & Gear

Center Cover & Gear

Motor DHG OnlyMotor DHG Only

Motor DHG Only

Motor & BaseMotor & Base

Motor & Base

DHG & SHGDHG & SHG

DHG & SHG

1515

2121

2222

ELECTRICAL SCHEMAELECTRICAL SCHEMA

ELECTRICAL SCHEMATICTIC

TICTIC

TIC

FOR THE LATEST SPECIFICATION INFORMATION GO TO WWW.WILBURCURTIS.COM

10/15/01.13.0 . edr 3167 Rev NC

Printed in U.S.A. 10/01 F-3209-S Rev NC

WARRANTY We hereby certify that the products manufactured by the Wilbur Curtis Company, Inc., are, to the best of our knowledge, free from all defects and faulty workmanship.

The following warranties and conditions are applicable:

• 90 Days for Labor and 1 Year Parts from Date of Purchase from Factory: This warranty covers all electrical parts, fittings and tubing.

• 40 Months or 40, 000 Pounds of Coffee on a set of Grinding Burrs. (ADS Grinders)

• 2 Years from Date of Purchase: This warranty covers electronic control boards and leaking or pitting of a stainless steel body of a Brewer or Urn.

• 90 Days from Date of Purchase: On replacement parts that have been installed on out of warranty equipment

All in-warranty service calls must have prior authorization from the manufacturer. For an RMA(Return MerchandiseAuthorization) number, call the Technical Service Department at 1-800-995-0417. The Wilbur Curtis

Company will allow up to 100 miles, round trip, per in-warranty service call.

CONDITIONS & EXCEPTIONS

The warranty covers original equipment at time of purchase only. The Wilbur Curtis Company, Inc., assumes no responsibility for substitute replacement parts installed on Curtis equipment that have not been purchased

from the Wilbur Curtis Company. Inc The Wilbur Curtis Company will not accept any responsibility if the following conditions are not met. The warranty does not cover and is void under these circumstances:

1) Improper operation of equipment. The equipment must be used for its designed and intended purpose and function.

2) Improper installation of equipment. This equipment must be installed by a professional, certified technician and must comply with all local electrical, mechanical and plumbing codes.

3) Wilbur Curtis Company will not be responsible for the operation of equipment at other than the stated voltages on the serial plate.

4) Abuse or neglect (including failure to periodically clean or remove lime accumulations). Manufacturer is not responsible forvariation in equipment operation due to excessive lime or local water

conditions.

5) Replacement of items subject to normal use and wear. This shall include, but is not limited to, light bulbs, shear disks, “0” rings, gaskets, canister assemblies. whipper chambers and plates, mixing

bowls, agitation assemblies and whipper propellers.

6) Any faults resulting from inadequate water supply. This includes, but is not limited to, excessive or low water pressure, and inadequate or fluctuating water flow rate.

7) All repairs and/or replacements are subject to our decision that the workmanship or parts were faulty and the defects showed up under normal use.

8) All labor shall be performed during regular working hours. Overtime charges are the responsibility of the owner.

9) Charges incurred by delays, waiting time, or operating restrictions that hinder the service technician’s ability to performservice is the responsibility of the owner of the equipment.

This includes institutional and correctional facilities.

10) All claims under this warranty must be submitted to the Wilbur Curtis Company Technical Service Department before return of the unit to the factory.

11) All equipment returned to us must be repackaged properly in the original carton. No units will be accepted if they are damaged in transit due to improper packaging.

12) Damaged in transit.