Customatic FEATHER LITE User manual

FEATHER LITE
ADJUSTABLE BED
Model Number: RTGFL01
This product and all our bedding products are covered by one or
more of the following issued and pending U.S. patents including
Nos. 7448100, D657157, D663542, D657158, D657156, 8209801,
8209800, D663544, D663543 and other patents pending.
Photos are for illustration purposes only.
COPYRIGHT © 2018 CUSTOMATIC®
Serial Number: _____________________________
(Place your serial number here for ready reference)
Owner’s Manual
“Wake Up to the Future”

NOTE: The serial number of your Feather Lite can be found under the head and foot sections of your adjustable bed.
CUSTOMATIC®is a registered trademark of PPJ, LLC; d.b.a. Customatic Technologies and Customatic Adjustable Bedz.
All other product names, brands, and trademarks are the property of their respective owners.

Safety Precautions
Parts List
Installation Guide
Remote Control Guide
Special Function
Troubleshooting
Warranty & Registration
4
6
7
12
14
15
18
Table of Contents
11.21.2018

4
Safety Precautions
ATTENTION!
IMPORTANT SAFETY INSTRUCTIONS.
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE USING THIS PRODUCT.
FOR OPTIMAL SAFETY, YOUR ADJUSTABLE BED SHOULD BE PLUGGED INTO A SURGE
PROTECTOR (not supplied with this adjustable bed).
ELECTRICAL SAFETY
Always unplug this adjustable bed from the electrical outlet
before any cleaning or maintenance of the bed. To safely
disconnect, make sure all controls are in the off position, then
remove the plug from the outlet.
Keep cord away from heated surfaces. Keep air openings free
of lint, hair and the like. Never operate when air openings are
blocked. Never drop or insert any object into any opening. Use
only indoors.
Cease use of this adjustable bed and contact the Customer Care
Center for repair if: (1) it has a damaged cord or plug, (2) it is not
working properly, (3) it has been dropped or damaged, or (4) it
has been dropped into water.
GROUNDING SAFETY
To reduce the risk of electric shock, electrical fire, or faulty
operation of this product, your adjustable bed may feature a
polarized plug meant to be used only with a grounded electrical
outlet. If this plug does not fit into your outlet, contact a qualified
electrician to install a properly grounded outlet. Failure to use
a properly grounded outlet for this product will compromise
this important grounding safety feature. The use of adapters
is not recommended unless the outlet is checked by a qualified
electrician to ensure the proper grounding of the adapter.
NOTE: Unauthorized modifications to this product could void
the electrical portion of your warranty.
WARRANTY WARNING!
This bed is specifically designed to require no maintenance by
you, the user. Any opening or tampering with the control box,
motors, or hand controls (with the exception of the battery
compartment if equipped) will result in a void of the warranty.
Only those authorized may conduct repairs or part replacement
on your adjustable bed. Unauthorized modifications to this
product could void the electrical portion of your warranty.
IN-HOME USE ONLY
This adjustable bed is designed exclusively for in-home use.
HOSPITAL DISCLAIMER: It is NOT designed for hospital use
and is NOT designed to meet hospital standards. Do not use
this bed with TENT TYPE oxygen therapy equipment or use near
explosive gases.
IMPORTANT SAFETY FEATURES
Weight fail safe feature: In the case that an overload of
weight is placed on the head or foot mechanism, the control
unit will automatically stop all functions. The control unit will
automatically resume all functions 30 seconds after excess
weight is removed.
The recommended weight limitations for your adjustable bed
is 850 lbs. on all sizes. For your adjustable bed to structurally
support the recommended weight, weight must be distributed
evenly across the head and foot sections. The adjustable bed
will not and is not intended to support or lift this amount in just
the head or foot section. Dependent on the size and/or model
of mattress, the available weight limit may be less.
Locking caster feature: This adjustable bed may be equipped
with special locking casters. For your safety, these casters will
prevent bed movement when all casters are in the locked
position. To lock casters, push down the safety latch on the
caster. To resume product mobility, lift the safety latch up.
NOTE: If your adjustable bed is positioned on a hard floor
surface such as hardwood or tile, it is strongly recommended
that rubber caster cups or carpet squares are placed under the
casters in addition to locking them in place. Casters will not roll
when locked, but may slide on an uncarpeted surface.

5
Safety Precautions
SAVE THESE INSTRUCTIONS.
Proper operation of your adjustable bed is necessary to ensure the long life and durability you expect
from a high-quality product. The manufacturer has tested and inspected this product prior to shipment.
USER-SERVICEABLE PARTS
This bed is specifically designed to have no maintenance by you,
the user. Therefore, you are encouraged not to open any motors,
alter the wiring, or adjust, modify or change the structure of the
product, as it will void the warranty.
RADIO FREQUENCY IS 2.4 GHZ
FCC compliant device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
IMPORTANT NOTE: To comply with the FCC RF exposure
compliance requirements, no change to the antenna or
the device is permitted. Any change to the antenna or the
device could result in the device exceeding the RF exposure
requirements and void user's authority to operate the device.
CONSUMERS WITH PACEMAKERS
It is possible that the (optional) vibrating feature of this adjustable
bed may be misinterpreted by some pacemakers as movement
and/or exercise. This is common with any product that produces
a vibrating motion, and may or may not affect your pacemaker.
Please consult your physician with any concerns.
PRODUCT RATINGS
Lift Motor Restrictions: The lift motors in this bed are NOT
designed to operate continuously for more than three (3)
minutes over a thirty (30) minute time period, or approximately
10% duty cycle. To ensure reliable functionality and full life of
this product, do not attempt to exceed these limits.
NOTE: Attempting to circumvent or exceed this rating will shorten
the life expectancy of the product and may void the warranty.
The structure of the bed will support the recommended
weight when distributed evenly across the bed. The head and
foot sections are not designed to individually support or lift
this amount of weight. For optimal performance, entering
and exiting the adjustable bed with the bed in the flat or level
position is recommended.
NOTE: Exceeding the recommended weight restrictions could
damage your adjustable bed and void your warranty.
SMALL CHILDREN AND PETS WARNING
Immediately dispose of all packing materials as it can pose a
smother risk to small children and pets. Injury could occur also
if children or pets are permitted to play on or under the bed. Do
not allow children to operate this bed without adult supervision.
LIFT WARNING
Do not sit on the head or foot sections while in the raised
position, or during lift or lowering cycles.
MOVING AFTER INSTALLATION
Do not place adjustable bed vertically on its head or foot sections.
This may cause injury to persons or damage to the adjustable
bed. Two people are required for moving this adjustable bed
due to its heavy weight.
SAFETY
Massage motors, if any, will automatically shut off after running
continuously for 15 minutes. All massage functions will be
operational again after 5 minutes.
The input transformer voltage is AC 120V 60HZ; the output
voltage is DC24V 3A. In the case of a short circuit, a fuse on the
transformer will blow to protect the electrical equipment (Fuse:
1A~1.5A). If this occurs, seek professional assistance to replace
the fuse. Contact our Customer Care Center.
NOTICE: The changes or modifications not expressly approved
by the party responsible for compliance could void the user's
authority to operate the equipment.
Read the Owner's Manual carefully and completely before
operating the product. Electric shock may occur if electrical
components are not installed or operated according to these
guidelines.

6
Parts List
Before discarding any packing materials, check the adjustable bed carton and verify that all items in the
parts list are included.
Remote control (1) AA batteries (2) Center support brackets (2) Knob screws &
spring washers (8)
Post bed legs (6) Mattress retainer
bracket (1)
Bed leg strap (1) **
*R pins are attached to both ends of the mattress retainer bracket.
** Only available with Twin XL models.
Headboard Bracket Parts
Inner headboard
bracket (2)
Outer headboard
bracket (2)
Retainer bolt (2) Washer (2) Allen key wrench (1)
NOTE: Headboard bracket parts may be sold separately.
R pins (2) *

7
NOTE: For safety reasons, lifting of the adjustable bed must always be performed by two (2)
people; and the unit should always be on a flat surface before opening.
Installation Guide
Setting up your adjustable bed frame
1
2
Open the box and unfold the bed placing it on a flat surface
with the top side facing downward.
Remove the accessory box and cut the orange ties from
inside the bed frame.
Attaching the center support bracket
Move the three sections of the bed closer together. Make
sure the bars and frames are properly aligned at the center.
To connect the three sections, put the center support bracket
over the bars on one side of the bed frame, lining it up with
the pre-drilled holes.
Thread the big knob screw fitted with a spring washer into
the first pre-drilled hole on the bracket and through the bed
frame. Hand tighten the screw to secure it in place.
Do the same for the rest of the holes on the center support
bracket.
1
2
3
4

8
Installation Guide
Insert the push pin into the pre-drilled hole in the middle
of the bracket and through the bar of the middle frame to
attach it to the rest of the bed.
Repeat steps 2 to 5 to attach the other center support bracket
to the other side of the bed frame.
5
6
Attaching the bed legs
1
2
Take out the six (6) post bed legs from the accessory box.
Attach the post bed leg to the bed frame by threading it in a
clockwise direction into the pre-drilled holes.
Repeat to attach the remaining bed legs.
Setting up the electronics
1Connect the cord for the foot lift motor to the control box.
Plug it into the port labeled "Foot Actuator".
Remove and extend the power cord from the frame.
2
Complete bed legs and
electronics assembly

9
Installation Guide
IMPORTANT!
Make sure power
cords do not obstruct
any adjustable bed
mechanisms.
5
Lift the bed frame and turn it over carefully so the top side is
now facing upward.
NOTE: Do not rest the frame on its side. The weight may
damage the legs.
Plug the power cord into a grounded electrical outlet.
NOTE: For optimal safety, using a surge protector (not
included) is highly recommended.
Install batteries in the remote control. Try all functions on
the remote to make sure all features are operational.
Return bed to flat position before continuing with the
installation.
NOTE: Make sure your bed is in a flat position before using
it. Press the FLAT button on the remote control for over 1.5
seconds after plugging in the power cord.
6
4
Attaching the mattress retainer bracket
Remove the pin from both ends of the retainer bracket.
Align both ends of the retainer bracket with the holes located
at the foot of the bed, and then insert them into the holes.
From under the bed, re-attach the pins to both ends of the
retainer bracket to keep them in place.
1
2
3
If a headboard is to be installed, see “Assembling the
headboard bracket.”
If the adjustable bed is set up without a headboard,
place your mattress on the adjustable bed surface. Your
adjustable bed installation is now complete.
7

10
Installation Guide
Installing the bed leg strap (optional)
Wrap the bed legs (front & back) together tightly using the
bed leg straps.
Fasten the straps to prevent movement & maintain stability.
1
2
To help prevent base separation when using two adjustable beds
together, use the bed leg straps.
Installing on a platform bed (optional)
To install your adjustable bed on a platform bed, do the following:
Assemble the adjustable bed.
NOTE: Do not install the bed legs.
Set up the electronics.
Turn the adjustable bed over carefully and place it on top of
the platform bed.
NOTE: For safety reasons, two (2) people should always lift
the adjustable bed.
Plug the power supply cord to a working electrical outlet, and
then check that the remote control and all bed functions are
working properly.
Install the mattress retainer bracket.
Place your mattress on the adjustable bed surface.
1
2
3
4
5
6

11
Installation Guide
Assembling the headboard bracket (optional)
1Turn the bed frame unit over with the top side facing down.
Remove the leg at the head section of the bed frame by
turning the leg counter-clockwise.
Slide the inner headboard bracket over the hole for the leg
attachment.
Thread the leg back in, turning clockwise. This will secure the
inner headboard bracket between the bed frame and the leg.
Place the open side of the outer headboard bracket onto
the exposed square tube of the inner headboard bracket to
create a tight fit.
Insert a retainer bolt fitted with a washer through the outer
headboard bracket and into the inner headboard bracket.
Tighten the bolt with an Allen key wrench. Leave loose
enough for adjusting.
Repeat steps 2 to 6 to install the brackets on the other side of
the head section of the bed frame.
When the headboard brackets are assembled, make sure
there is a space of 1.5 inches (38.1 mm) to 2 inches (50.8
mm) between the edge of the bed frame and the headboard
brackets.
Securely fasten the headboard bolts (not included with your
parts box) to the end of the headboard bracket assembly.
Turn the bed frame over carefully with the topside facing up.
If you need to adjust the headboard brackets, unscrew
the bolts holding the outer headboard bracket and move
them the necessary distance. Reinstall the bolts and tighten
securely.
2
3
IMPORTANT!
• Failure to follow the installation steps as they appear in this guide could result in damage to your
adjustable bed.
• For safety reasons, lifting of the adjustable bed must always be performed by two (2) people; and the
unit should always be on a flat surface.
• Make sure to position the bottom of the headboard cross member no more than 3 inches (76.2 mm)
between the headboard and the top of the mattress.
4
5
6
7
8
9
10
11
Place your mattress on the adjustable bed surface.
Your adjustable bed and headboard installation is now
complete.

12
Remote Control Guide
Understanding the remote control features
• The adjustable bed uses RF (radio frequency) 2.4 GHz remote control system.
• It is not necessary to face the receiver when operating the remote control. Remote signal is best transmitted
within 9 feet (3 meters) of the bed.
NOTE: The bed may show minor intermittent performance because of typical radio frequency interference. This
is normal in the operation of the bed, not a defect.
Head Position Adjustments (1, 2)
Press the button to raise or lower the head section of your adjustable bed.
Foot Position Adjustments (3, 4)
Press the button to raise or lower the foot section of your adjustable bed.
Flat (5)
Press and hold this button to return the bed to a flat position.
NOTE: Make sure your bed is in a flat position before using it. Press the Flat button on the remote
control after plugging in the power cord.
1
2
3
4
5

13
Remote Control Guide
Synchronizing two beds for tandem operation
To operate two adjustable beds simultaneously, you must pair both beds (Bed A and Bed B) to one remote control
(Remote A).
LED light on the control box
Plug both Bed A and Bed B to working and grounded electrical
outlets. A surge protector is recommended.
Before starting the sync process, press the FLAT button on
Remote A and Remote B to align the beds properly.
On Bed B, the LED light on the control box blinks three (3) times
once the power cord is plugged in, and is in learning mode for
seven (7) seconds.
During learning mode, use Remote A and press the HEAD UP
and FOOT UP buttons at the same time for three (3) seconds.
The LED light on the control box will light up and remain on,
which means the pairing is successful. Bed A and Bed B can
now be controlled simultaneously using Remote A.
NOTE: When operating beds in tandem, both beds should be
plugged into working and grounded electrical outlets.
1
2
3
4
Resetting your system
Unplug the power cord of your adjustable bed from the
electrical outlet.
Press and hold the FLAT button (without releasing) to continue
sending a signal.
Plug the power cord back to the outlet and wait for seven (7)
seconds, then release the FLAT button.
NOTE: The control box must receive the Flat signal from the
remote control for at least five (5) seconds after the power cord
is plugged back in. The reset is complete.
1
2
3
Resetting the system is sometimes necessary to:
• Restore the system to its factory setting.
• Clear a system error.
• Synchronize tandem units that no longer work in tandem.
• Change a tandem system back to a single system or to two independent systems.

14
Special Function
Activating the emergency power down feature
Locate and remove the cover on the 9V battery compartment
of your control box.
Install two (2) alkaline 9V batteries (not included with the
adjustable bed).
Replace the battery cover.
When the 9V batteries are installed and a power failure occurs,
press the FLAT button on the remote control for the bed to
return to a flat position.
NOTE: The 9V batteries are for single use only. After lowering
the adjustable bed once during a power failure, replace with a
new set of batteries.
1
3
2
4
Your adjustable bed supports the emergency power down feature for when a power failure occurs while the head
and/or foot sections are raised.

15
In the event the adjustable bed fails to operate, investigate the symptoms and possible solutions below.
Troubleshooting
• Check that the power cord is plugged into a working
electrical outlet. Unplug the power cord from the
outlet. After 30 seconds, plug it back in. Press any
button on the remote control and check if the bed
responds.
• Check if the control box is working properly. Make
sure the control box is properly connected to the
power supply unit by checking if the LED light turns
on when the power cord is plugged in.
• Check the batteries in the remote control. Replace
with new batteries, if necessary.
• Make sure batteries are properly installed. Follow the
markings on the battery compartment.
• Remove batteries. Leave them out for 30 seconds
before putting them back into the remote control.
• Scratch the terminals inside the remote's battery
compartment with a coin or key.
• Check that the surge protection device or electrical
outlet is not defective. Test the outlet by plugging in
another working appliance.
The adjustable bed does not respond
when the remote is used. The remote
does not work.
• Make sure the remote control is paired with the
adjustable bed.
• Check that the power cord is plugged into a working
electrical outlet. Unplug the power cord from the
outlet. After 30 seconds, plug it back in. Press any
button on the remote control and check if the bed
responds.
• Check that the surge protection device or electrical
outlet is not defective. Test the outlet by plugging in
another working appliance.
No features or function of the
adjustable bed activates.
SYMPTOM SOLUTIONS

16
In the event the adjustable bed fails to operate, investigate the symptoms and possible solutions below.
Troubleshooting
SYMPTOM SOLUTIONS
• Your adjustable bed may be obstructed
preventing smooth operation. Remove
obstructions from around and under the bed.
• Check that the head section is not too close to
the wall.
• If a headboard is installed, check that it is not
too close to the edge of the mattress. Make sure
there is enough distance between the headboard
bracket and the mattress.
Head or foot section elevates adjustable
bed but does not return to flat position.
• Check the batteries in the remote control.
Replace with new batteries, if necessary.
• Make sure that you are following the duty
cycle of the motors. Do not operate for more
than two minutes over a 20-minute period or
approximately 10% duty cycle.
• Press the lift buttons firmly and accurately.
• Wireless remote control may be experiencing
common radio frequency interference from
other radio transmitting devices. Wait several
seconds and then try pressing the lift buttons
again.
Head or foot lift function has minor
interference during operation.
This is normal. The lift motors click when they are
engaged. No action is required.
A clicking noise is heard under the bed
when raising or lowering the sections.

17
Troubleshooting
In the event the adjustable bed fails to operate, investigate the symptoms and possible solutions below.
1. Remove any pin, nut, bolt, or white bushing one at a
time.
2. Lubricate it by applying the grease with a cotton
swab. Using a lithium or spray lubricant is
recommended. (Lubrication can be obtained by
contacting Customatic's Customer Care Center).
3. When placing the lubricated pin, nut, bolt, or white
bushing back onto the adjustable bed, make sure
there is a looser tightening on the nut.
4. Additional solution: After completing these steps,
spray the pins, nuts, bolts, and white bushings with a
lubricant.
The adjustable bed is squeaking.
1. Clear any clutter or obstructions under and around
the adjustable bed. Radio frequency interference
from other remotes or electronic devices may affect
normal operation.
2. Check the batteries in the remote.
3. Press the lift buttons on the remote control firmly
and accurately.
The adjustable bed stutters when in
motion.
Sync one remote to both adjustable beds. For more
information, see "Synchronizing two beds for tandem
operation" on page 13.
Split or tandem system is out of sync.
Only one of the two adjustable bed
raises or both beds raise but one side is
higher than the other.
SYMPTOM SOLUTIONS

18
Warranty
Limited Warranty For Adjustable Beds
LIMITED WARRANTY: Subject to the terms and conditions
set forth herein, the manufacturer of this product, PPJ, LLC
(“Customatic®”) warrants to the original retail purchaser
for the time periods stated herein that the adjustable bed
system purchased from an authorized reseller of genuine
Customatic® products is merchantable and free of defects and
materials and is fit for the purpose of residential, non-hospital
bedding. Floor samples are not warranted and are purchased
AS IS. This warranty applies only to genuine Customatic®
products, and without limiting the foregoing, does not apply
to power cords or other accessories supplied by the seller or
other parties.
20-Year Period for Bed Frame: The above warranty will apply
for 20 Years to the bed frame, defined as follows: the metal
structure of the adjustable bed system only, and specifically
does not include its cover, side rails, decking or legs, or other
attachments thereto, such as actuator lift motors, control box,
WiFi modules, power supply, power cords, control box or other
electrical or mechanical components.
5-Year Period for All Other Components: The above
warranty will apply for 5 years for all components other than
the bed frame as defined above, including, without limitation,
electronics, electrical components, drive motors, WiFi module,
power supply and power cords, and massage motors.
Start of Warranty Period: The warranty periods stated above
will commence on the date of the first retail purchase of the
adjustable bed system from an authorized Customatic reseller,
provided that proof of purchase and warranty registration
occur within the time and in the manner set forth below. In
the case of replacement parts provided by Customatic, the
warranty will apply to the original warranty period and will not
extend beyond such period.
NO OTHER WARRANTY EXPRESS OR IMPLIED: The foregoing
express warranty is the only warranty by Customatic and
all other express warranties or warranties implied by law
or otherwise (including without limitation, any implied
warranty of fitness for a particular purpose) are hereby
denied and disclaimed to the full extent permitted by
applicable law.
EXCLUSIONS FROM WARRANTY: Loss, damage, malfunctions
or other defects caused in whole or in part by any one or
more of the following are not covered by any warranty and
neither Customatic nor the seller shall be responsible for
them: ordinary wear and tear; damage not directly caused by a
defect covered by this express warranty; failure to comply with
this user Manual and/or any other user instructions issued
by Customatic for use and maintenance, including without
limitation, weight limits and operation; modifications not
performed by Customatic; use of any parts, components, or
accessories that are not supplied by Customatic for the specific
product and installed by an authorized Customatic service
provider; use of the product for purposes or in a manner
not expressly intended by Customatic as described in this
Manual or any other misuse or abuse; storage or use outside
of home or other exposure to the elements; dampness;
or transportation or other handling by anyone other than
Customatic.
EXCLUSIVE LIMITED REMEDY: The sole and exclusive
remedy for any item which fails to meet the express
written warranty set forth above shall be, at Customatic’s
option, either repair or replacement of the defective
item. Customatic may require reasonable evidence of the
existence of a defect, and Customatic customer service staff
will discuss specific requirements with the purchaser based
on the defects identified by the purchaser. Replacement parts
will be provided at no cost to the purchaser, provided that the
defective parts are delivered to Customatic, unless Customatic
instructs otherwise in the claims process (see below). Subject
to advance approval by Customatic, it will also pay reasonable
labor by an authorized Customatic service technician or other
qualified person approved by Customatic and shipping costs
for returns requested by Customatic and replacement parts or
bedding systems.
CLAIMS PROCESS: Prior to contacting Customatic, please
refer to the TROUBLESHOOTING section of this Manual and
also ensure that use and maintenance instructions in this
Manual have been followed. The following process must
be followed to initiate a warranty claim: (1) during the
applicable warranty period stated above, contact Customatic
customer service to initiate the claim and provide proof of
status as the original retail purchaser from an authorized
Customatic® products reseller and prior timely registration of
the product (see PRODUCT REGISTRATION); (2) identification
of suspected defect and compliance with Customatic requests
for documentation or other evidence of the defect, such as

19
Registration
NAME ________________________________________________
PHONE _______________________________________________
ADDRESS _____________________________________________
CITY _________________________________________________
STATE __________________________ ZIP CODE ___________
EMAIL ADDRESS ______________________________________
STORE WHERE PURCHASED __________________________
SERIAL NO. ___________________________________________
INVOICE NO. _________________________________________
MODEL NO. __________________________________________
SURVEY
GENDER: __ M __ F
AGE: __ 18-30 __ 31-40 __ 41-50
__ 51-60 __ 61-70 __ 71 & up
Reason for purchasing an adjustable bed:
___ Health ___ Comfort ___ Other
How did you find out about our beds?
___ Advertising ___ A friend
___ Store ___ Article
___ Internet ___ Other
Please mail to:
CUSTOMATIC® TECHNOLOGIESTM
Customer Care Center
550 Crescent Blvd., Gloucester City, NJ 08030
WARRANTY REGISTRATION FORM
You can also register your bed online at www.customaticbeds.com.
return of parts to Customatic, the cost of which will be paid
by Customatic if the defect is confirmed by it or inspection by
an authorized Customatic service technician or other person
approved in writing for that purpose by Customatic; and (3)
remedy by Customatic as stated herein.
LIMITATION OF LIABILITY: In no event shall Customatic
be liable for incidental or consequential damages of any
kind or nature whatsoever caused by or arising out of any
product defects, and the sole and exclusive remedy shall be
repair or replacement of defective items within warranty
to the extent and in the manner provided herein.
“Wake Up to the Future”

IF YOU EXPERIENCE ANY TROUBLE WITH YOUR ADJUSTABLE
BED WITHIN THE WARRANTY PERIOD, PLEASE CONSULT THE
TROUBLESHOOTING GUIDE PROVIDED WITH YOUR BED AND
ONLINE, IF APPLICABLE. IF PROBLEMS PERSIST, PLEASE CALL:
CUSTOMER SERVICE TOLL FREE NUMBER
1-720-458-5955
Please have your receipt ready and available.
THANK YOU AND ENJOY YOUR ADJUSTABLE BED!
POWERED BY
“Custom Sleep to Fit Your Life”