CY MODEL Reggiane RE 2005 User manual

Before commencing assembly,please read these instructions thoroughly.
SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time builders should seek advice from people having building
experience in order toassemble the model correctly and to produce
its performance to full extent. ,
lAssemble this kit only inplaces out of childrens reach!
lTake enough safety precautions prior to operating this model.
,
You are responsible for this models assembly and safe operation!
lAlways keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
lCould cause serious injury or even death
SPECIFICATION
Reggiane RE 2005
Thank you for choosing CYmodel
Global : www.cymodel.com
Australia : www.austars-model.com
Italia : www.biellaexpress.com
Instruction Manual
Wing Span.......2400 mm (94.5 in)
2
Wing Area.......97 dm (1504 sq.in)
Take-off weight....13.5 kg
Length..............1970 mm (78in)
Engine..............50-80cc gas engine
Radio................6 channels, 8 servos
Designed and Manufactured by : CYmodel Http : // www.cymodel.com
Item Nr: CY8146

22
REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)
BEFOREYOU BEGINBEFOREYOU BEGIN
Sharp Hobby Knife Phillips Screw Driver Awl
Needle Nose Pliers Wire Cutters Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local deater.
Symbols used throughout this instruction manual,comprise.
11
22
33
.
.
.
Warning!
£¡
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
2mm
Assemble left and right
Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
BA
Cut off excess.
!
Do not overlook this symbol.
11
Aminimum 6 channel radio for airplanes (with 8 servos).
And dry batteries.
CAUTION: Only use a minimum 6 channel radio for
airplanes! (No other radio may be used!)
!
12 AA-size Batteries
Aminimum 6 channel
transmitter for airplanes.
22
For handing the radio properly.refer to its instruction manual.
Engine and Muffler
Muffler Glow plug
33
Purchase a propeller that
will match your engine
44
Silicone Tube Fuel Filter
55
required for engine starting Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump Plug Wrench
33
Glue
66
Instant glue Epoxy Glue
33
Other equipment for enhancing
airplane operation & perormance
77
12V Battery (for starter)
Engine Starter
Propeller splinner
MA
50-80 cc gas engine
odel irplane engine

!
Accessory list for this page.
3
Install the aileron
2
1
5
4
Epoxy flap hings to trailing edge
33
Install the servo
Epoxy pin hings to aileron steadily
Make sure hings are
mounted in the same line
-----------8
Pin hings
BA
Hinge
-----4
BA
BA
Securely glue together.If comingoff during flights,you'll
lose control ofyour airplane whichleads toaccidents!
Warning!Warning!
Flap Aileron
Tailing edge
Aileron
2mm
Rod adjuster
2.5X85mm rod
- - - - 4
- - - - - - 4
Rod adjuster
- - - - 4
- - - - - - 4
- - - - - - 4
Ball bearing
Ball bearing
3mm washer
- - - - - - 4
3X16mm Screw
- - - - - 4
3mm Lock nut
- - - - - - 4
-------8
Pin hings
Hinge
Rod adjuster
2.5X85mm rod
- - - - 4
- - - - - - 4
Rod adjuster
- - - - 4
- - - - - - 4
Ball bearing
Ball bearing
3mm washer
- - - - - - 4
3X16mm Screw
- - - - - 8
3mm Lock nut
- - - - - - 8
-------8
HORN--8
3X16 Screw--4
3mm Locknut--4
AB
Install the control horn and
connect the linkage
HORN--8
- - - - - - 4

!
8
710
9
44
6
Accessory list for this page.
Mount the landing gear
Instal the main landing gear
502
C.A
4mm Lock nut
- - - - - - 2
- - - - - - 4
3X3mm screw
- - - - - - - 4
M3X5mm Screw
- - - - 4
The hole for servos cable way
HORN--8
3X16 Screw --4
3mm Lock nut--4
4mm Lock nut
- - - - - - 2
- - - - - - 2
3X3mm screw
- - - - - - - 4
M3X5mm Screw
- - - 4
- - - - 2
3mm plywood
- - - - 2
3mm plywood
Mount the landing gear cover
Pleas notice the inner diameter for each
side of the pressure reduction inlet.
Please insure the sealing of the retract
system before flight .
Retainer
Rod adjuster
2X8mm screw
- - - - - 1
- - - - - 1
- - - - - 1
Rod (1.8X80mm)
- - - - 1
2000mm Air line
- - - - - 2
Quick release connector
3-way
pressure inlet
3-way
pressure inlet
Air inlet
Switch
Air tank
Air tank
Two wheel retract system

!
Accessory list for this page.
13
12 15
14
55
11
BB
AA
Carbon tube
- - - - 2- - - - 2
8.2mm
M5X65mm screw
Wing
Fuselage
M5 nut
M5X60mm screw
- - - - - - 4
5mm washer
- - - - - - - - - - - 4
5mm Blind Nut
- - - - - - - - - 4
8.2mm
Assemble the wings
Drill 8.2 mm holes at the place
of main wing
Install the wing to the fuselage
with M5X60mm screws as shown
in the diagrams below.
A = A1
Drill holes in the wings and set the Carbon fibre
dowels in them as below
Drill holes in the wings and set the Carbon fibre
dowels in them as below
Drill holes to relevant position in the fuselage
Assemble the wings to the fuselage with
screw and blind nut as below
55
Carbon tube
- - - - 2
M5X65mm screw
- - - - - - 4
5mm washer
- - - - - - - - - - - 4
5mm Blind Nut
- - - - - - - - - 4
70
70
412mm
72
5mm

!
Accessory list for this page.
18
17 20
19
66
16
M4x12mm Screw
4
3X3mm Screw
- - - - 4
5mm
B
A
B
A
Make sure hings are
mounted in the same line
-----------3
Pin hings
- - - - 4
8.2mm8.2mm
4mm4mm
Top
Bottow
Ply wooden
B
A
Ply wooden
B
A
Warning!
£¡
!
Securely glue together ,if coming
off during . You will lose control
of your airplane which leads to accidents!
Assemble the elevator to stabilizer
Epoxy pin hings to elevator
B
A
Install the servo
- - - - 4
Ply wooden
M4x12mm Screw
3X3mm Screw
- - - - 4
- - - - 4
-----3
Pin hings
Drill holes in the belly pants appropriate
position
Assemble the belly pants to the wings with
screw
Hardwood
- - - - 4
Hardwood
- - - - 4

!
Accessory list for this page.
23
22
24
7
21
25
Install the nylon control horn and the linkage
LL
RR
Rod adjuster
2.5X85mm rod
- - - - 2
- - - - 2
Rod adjuster
- - - - 2
- - - - - - 2
- - - - - - 2
Ball bearing
Ball bearing
3mm washer
- - - - - - 2
3X14mm Screw
- - - - - 4
3mm Lock nut
- - - - - - 4
HORN--4
3X16 Screw --2
3mm Lock nut--2
2.3x10mm Tp Screw
- - - - 8
The position of the control horn in the elevator
A B
BBB1B1
B=B1 AB
AWLAWL
Secure the servo. Install the nylon control horn
and connect the linkage
Assemble the stabilizer to fuselage as illustration
Assemble the stabilizer to fuselage as illustration
HORN--4
2.3x10mm Tp Screw
- - - - 8
Rod adjuster
2.5X85mm rod
- - - - 2
- - - - - - 2
Rod adjuster
- - - - 2
- - - - - - 2
- - - - - - 2
Ball bearing
Ball bearing
3mm washer
- - - - - - 2
3X14mm Screw
- - - - - 2
3mm Lock nut
- - - - - - 2

!
Accessory list for this page.
28
27
29
8
26
Instal the rudder in to the vertical fin
30
Epoxy pin hinges to elevator
4X15mm
screw
- - - - - - 2
4.2mm
Make sure hings are
mounted in the same line
-----------3
Pin hings
BA
Warning!
£¡£¡
!!
Securely glue together ,if coming
off during . You will lose control
of your airplane which leads to accidents!
BA
Aluminium tube
Rod
Steel wire
Rod adjuster
HORN
3X16 Screw
2
2
2
2
3mm Lock nut
2
2
2
2
AB
Assemble the stabilizer to fuselage as illustration
-------3
Pin hings
Aluminium tube
Rod
Steel wire
Rod adjuster
HORN
3X16 Screw
2
2
2
2
3mm Lock nut
2
2
2
2
Rudder . Connect the linkage
rod to the horn
Rudder . Connect the linkage
rod to the horn

!
Accessory list for this page.
33
32
34
9
31
35
Install the tail wheel
- - - - 1
- - - - 3
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 3
6X9 screw
- - - - 1
- - - - 1 6mm nut
4.5mm
3.2mm Rocker
- - - - - 1
Aluminium tube
Rod adjuster
- - - - - 2
Rod - - - - - 2
- - - - - 2
Steel wire
- - - - - 2
3X3mm Screw
- - - - 1
2
M4X20mm Cap screw
4mm Blind Nut
- - - - - - 2
2.3x10mm Tp Screw
- - - - - - 4
M5x65 screw
3mm plywood
Hardwood
After confirmingthe
position(see frontof
fuel tank).
Insert and tighten
the screw.
3X20mm Screw
- - - - 1- - - - 1
Assembly of the full tank
Assembly of the engine
Assemble the tail landing gear to the fuselage
Fitting of the tail wheel assembly
- - - - 1
- - - - 3
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 3
6X9 screw
- - - - 1
- - - - 1
6mm nut
3.2mm Rocker
- - - - - 1
Aluminium tube
Rod adjuster
- - - - - 2
Rod
- - - - - 2
- - - - - 2
Steel wire
- - - - - 2
3X3mm Screw
- - - - 1
2
M4X20mm Cap screw
4mm Blind Nut
- - - - - - 2
2.3x10mm Tp Screw
- - - - - - 4

!
Accessory list for this page.
38
37
39
10
36
40
Epoxy the fuel tank and rudder servo
in the fuselag
Rod adjuster
- - - 2 Rod - - - 2
Aluminium tube
- - - - - 2
Rudder
servo
BA
Fuel tank
Built nut
3mm ply
Cowling
M3X16 screw
M3X15mm screw
3mm Washer
- - - - - - 5 - - - - - - - - - 5
3mm plywood
- - - - - - 10
3mm Blind Nut
- - - - - - - 5
2.3X10Tpscrew
- - - - 6
BA
Assemble the antenna to fuselage with A/B glue
Assemble the canopy to the fuselage with TP screws
Assemble the cowling to fuselage with screw
Assemble the oil filler pipe to fuselage with A/B glue
Rod adjuster
- - - 2
Rod - - - 2
Aluminium tube
- - - - - 2
2.3X10Tp screw
- - - - 6
M3X15mm screw
3mm Washer
- - - - - - 5
- - - - - - - - - 5
3mm plywood
- - - - - - 1
3mm Blind Nut
- - - - - - - 5

43
42
5
44
Centre of Gravity.
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Never fly before checking the Cg s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
NEVER fly the model
without well balancing.
Warning!
!
41
AILERON
Adjustment.
Top view
Adjust the travel of eachcontrol surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needsand flight level.
Adjustment.
Adjustment.
1111
Top view
Side view
Top view Side view
58mm
58mm
100mm 100mm
CGCG
150-155mm
Take-off Landing