CYBELEC CybTouch 12 User manual

User Manual
for Synchronized Press Brakes
Sept14
V3.1

© 2014 Cybelec S.A.
All Rights Reserved
Copying, reproduction, modification, distribution, display or transmission of any of the contents of
this manual for any purpose without the prior consent of Cybelec S.A. is strictly prohibited.

The Intuitive Programming
Table of conTenT
Safety......................................................................................................................1
General Safety............................................................................................................................... 1
Signs and Icons appearing in this Manual.................................................................................. 2
General warning............................................................................................................................. 2
Information.................................................................................................................................... 2
Settings.......................................................................................................................................... 2
Navigation .................................................................................................................................... 2
Getting started with CybTouch 12 ..........................................................................3
General navigation ....................................................................................................................... 4
Menu Button ................................................................................................................................ 4
Status Pages Zone ........................................................................................................................... 4
Screen Cleaning .............................................................................................................................. 4
Status page .................................................................................................................................... 5
User Preferences .......................................................................................................................... 5
Language ...................................................................................................................................... 6
Length Units .................................................................................................................................. 6
Show Y1-Y2 position values.............................................................................................................. 6
Show page L-alpha num .................................................................................................................. 6
Show bent part................................................................................................................................ 6
Materials ....................................................................................................................................... 7
BDC correction ............................................................................................................................... 7
Clear indexation ............................................................................................................................. 8
USB Explorer.................................................................................................................................. 8
Default retraction............................................................................................................................ 8
Set Clock........................................................................................................................................ 8
Touchscreen Calibration................................................................................................................... 8
Brightness xx% Eco xx% ................................................................................................................ 9

The Intuitive Programming
Manual Axes Movement............................................................................................................... 9
Desynchronized Beam....................................................................................................................... 9
Service Page ................................................................................................................................ 10
Set Axis ........................................................................................................................................10
Maintenance.................................................................................................................................10
Defrag..............................................................................................................................................................11
Format .............................................................................................................................................................11
Internal backup ..............................................................................................................................................11
Information...................................................................................................................................11
Configuration options.....................................................................................................................12
Serial number .................................................................................................................................................12
Computer ID...................................................................................................................................................12
Option list .......................................................................................................................................................12
New option code.............................................................................................................................................12
USB Transfer............................................................................................................................... 13
Importing parts from other Cybelec NCs .............................................................................................13
Basic Page Description..........................................................................................14
Bend Numerical Page ................................................................................................................ 14
More Page................................................................................................................................... 14
Available functions on the More page................................................................................................15
Material ...........................................................................................................................................................15
Material thickness...........................................................................................................................................15
Material sigma.................................................................................................................................................15
Back gauge retraction ....................................................................................................................................15
Speed change threshold and bending speed ...............................................................................................15
Bending length ...............................................................................................................................................15
Step bending...................................................................................................................................................16
Slow speed return ...........................................................................................................................................16
Dwell time .......................................................................................................................................................16
Force................................................................................................................................................................16

The Intuitive Programming
Opening (TDC)..............................................................................................................................................17
Crowning.........................................................................................................................................................17
Back gauge finger type ...................................................................................................................................17
Number of parts .............................................................................................................................................17
Back gauge manual control ...........................................................................................................................17
Tools Management ................................................................................................18
Punches....................................................................................................................................... 18
How to create or modify a punch?.....................................................................................................19
Dies.............................................................................................................................................. 20
How to create or modify a die?..........................................................................................................21
Naming Tools.............................................................................................................................. 22
Punches........................................................................................................................................22
Dies..............................................................................................................................................22
Creating a Part Program........................................................................................23
TouchProfile Mode .................................................................................................................... 23
Automatic Bend Sequencing (optional)................................................................................... 24
Numerical Mode......................................................................................................................... 26
L-Alpha Mode............................................................................................................................. 27
Bend Correction......................................................................................................................... 28
Angle Correction (Y axis) ................................................................................................................28
Crowning......................................................................................................................................29
Back gauge (X & R axes) Correction ................................................................................................29
Saving and Loading a Program..............................................................................30
Saving a Program........................................................................................................................ 30
Loading a Program..................................................................................................................... 30
Deleting a Program .................................................................................................................... 30
EasyBend Page......................................................................................................31
Making a bend on the EasyBend Page...................................................................................... 31

The Intuitive Programming
Error and Warning Messages.................................................................................32
Warning Messages ...................................................................................................................... 32
Error Messages............................................................................................................................ 35

The Intuitive Programming

The Intuitive Programming

1/38
Sept.
2014
V3.1
CybTouch 12 PS User Manual
Safety
The users must have Read and UndeRstood, but most of all must Respect the
directives described in this manual.
All people coming into contact with the machine on which the numerical
control is installed, whatever their function or whatever state the machine is in
(assembly, disassembly, start-up, production, maintenance, repairs) must have
read and understood the requirements concerning the security and the entirety
of the directives of operation described in the manuals delivered with the
machine.
General SafeTy
The operator must be properly trained to work with the machine
on which the numerical control is installed. Improper use of the
numerical control can cause heavy damage on equipment and/or
injuries to people.
Modification of machine parameters can cause important material damage or
lead to irregular product quality.
Do not expose the numerical control to excessive humidity so as to avoid any
risk of electrocution and any deterioration of the equipment.
Make sure the numerical control is disconnected from the mains power before
carrying out any cleaning. Do not use liquids based on alcohol or ammoniac.
In case of malfunction of the numerical control, call a technician.
Do not expose the numerical control to direct sun rays or any other heat source.
Do not place the numerical control in the neighborhood of magnetic equipment
such as transformers, motors or devices which generate interference (welding
machines, etc.)

2/38 Sept. 2014
V3.1
CybTouch 12 PS User Manual
SiGnS and iconS appearinG in ThiS Manual
While using this manual, you will come across the signs and icons represented here
below: they are directly related to the safety and security of persons. Carefully follow this
advice and inform others about it.
General warning
Information
Settings
Navigation
This warning sign appears in the manual whenever it is necessary to pay attention to
rules, instructions or advice. The correct sequence of operations is to be followed in order
to avoid damage to the machine.
Symbolizes a serious personnel danger
This warning sign appears in this manual whenever an important information needs to be
taken into consideration. Pay attention to this sign and follow the instructions given.
This sign appears in this manual whenever setting instructions are given. Pay attention to
this sign and follow the sequence of instructions given.
This icon appears in this manual to give navigation information, to give the path to the
subject treated in the chapter.