CYBELEC VisiPac Series User manual

VisiPac
VisiTouch
Series
User Manual
MARCH
2021
V1.0
for Synchronized Press Brakes

User Manual –VisiPac & VisiTouch Series
VisiPac & VisiTouch Series –
User Manual
MAR.
2021
V1.0
1/69
© 2020 Cybelec S .A. All
Rights R eserved
Copying, reproduction, modification, distribution, display or transmission of anyof the contents of this
manual for any purpose without the prior consent of Cybelec S.A. is strictly prohibited.

User Manual –Visipac & VisiTouch Series
VisiPac & VisiTouch series –User Manual
MAR.
2021
V1.0
2/69
Table of Contents
Safety....................................................................................................................................................................6
General Safety ..................................................................................................................................................6
Signs and Icons appearing in this Manual ........................................................................................................7
General warning ...........................................................................................................................................7
Information...................................................................................................................................................7
Settings.........................................................................................................................................................7
Navigation.....................................................................................................................................................7
Getting started with VisiPac & VisiTouch.............................................................................................................8
Screen Map.......................................................................................................................................................9
Screen Map (continued)................................................................................................................................ 10
General navigation ........................................................................................................................................ 11
Menu Button ............................................................................................................................................. 11
Status Page Zone ....................................................................................................................................... 11
Screen Cleaning ......................................................................................................................................... 11
Status page .................................................................................................................................................... 12
User Preferences ........................................................................................................................................... 13
Language.................................................................................................................................................... 13
Length Units............................................................................................................................................... 14
Force Units................................................................................................................................................. 14
Force / Length Units .................................................................................................................................. 14
Sigma Units................................................................................................................................................ 14
Show axes position values......................................................................................................................... 14
Show bent part .......................................................................................................................................... 14
Materials.................................................................................................................................................... 15
BDC Correction .......................................................................................................................................... 16
Menu horizontal alignment....................................................................................................................... 16
Menu vertical alignment ........................................................................................................................... 16
Clear indexation......................................................................................................................................... 17
USB Explorer.............................................................................................................................................. 17
Beam trace................................................................................................................................................. 17
Auto open beam trace............................................................................................................................... 17
Default retraction...................................................................................................................................... 17
Set Clock .................................................................................................................................................... 17
Touchscreen Calibration............................................................................................................................ 18
Offset Pinch Point function........................................................................................................................ 18
Show button up......................................................................................................................................... 18
Program counter mode ............................................................................................................................. 18

User Manual –VisiPac & VisiTouch Series
VisiPac & VisiTouch Series –
User Manual
MAR.
2021
V1.0
3/69
Show L first ................................................................................................................................................ 18
Indexation Aids.......................................................................................................................................... 19
Disable recalculation at product load........................................................................................................ 19
Beam stop during retractation .................................................................................................................. 19
Working directories................................................................................................................................... 19
Bend list columns configuration................................................................................................................ 20
Bending pages buttons configuration ....................................................................................................... 22
Manual Axes Movement ............................................................................................................................... 23
Desynchronized Beam............................................................................................................................... 23
Linked axis ................................................................................................................................................. 23
Information Page........................................................................................................................................... 24
USB Transfer.................................................................................................................................................. 25
Precautions................................................................................................................................................ 25
Importing parts from PC program............................................................................................................. 25
Backup and restore........................................................................................................................................ 26
Backup ....................................................................................................................................................... 26
Restore....................................................................................................................................................... 26
Delete Backup............................................................................................................................................ 26
Basic Page Description....................................................................................................................................... 27
Bend Numerical Page .................................................................................................................................... 27
Available functions on the Bend Num page .............................................................................................. 27
Quick access tab ........................................................................................................................................ 30
User button tab ......................................................................................................................................... 30
Extra Bending Parameters......................................................................................................................... 31
Copy to All Function ...................................................................................................................................... 35
Tools Management............................................................................................................................................ 36
Punches ......................................................................................................................................................... 36
Punches options ........................................................................................................................................ 37
Dies................................................................................................................................................................ 39
Punches options ........................................................................................................................................ 40
Naming Tools................................................................................................................................................. 42
Punches ..................................................................................................................................................... 42
Dies............................................................................................................................................................ 42
Creating a Part Program .................................................................................................................................... 43
Graphical 2D .................................................................................................................................................. 43
Mode ............................................................................................................................................................. 43
Touch profile mode ................................................................................................................................... 44
L-Alpha mode............................................................................................................................................. 45
U-W mode ................................................................................................................................................. 46

User Manual –Visipac & VisiTouch Series
VisiPac & VisiTouch series –User Manual
MAR.
2021
V1.0
4/69
Multi profiles ............................................................................................................................................. 47
Bend Sequencing........................................................................................................................................... 48
Page Simulation Criteria ............................................................................................................................ 49
Bend 2D Page................................................................................................................................................. 50
Add extra bends in graphic parts............................................................................................................... 51
Numerical Mode............................................................................................................................................ 52
Bending and Corrections ............................................................................................................................... 53
Semi-Automatic mode............................................................................................................................... 53
Angle Correction (Y axis)............................................................................................................................ 54
Crowning.................................................................................................................................................... 55
Back gauge Correction............................................................................................................................... 55
Managing Programs........................................................................................................................................... 56
Saving a Program........................................................................................................................................... 56
Creating a Program........................................................................................................................................ 56
Loading a Program......................................................................................................................................... 57
Deleting a Program........................................................................................................................................ 57
Extra Fonction.................................................................................................................................................... 58
Group and Batch............................................................................................................................................ 58
Station management..................................................................................................................................... 60
Troubleshooting ................................................................................................................................................ 62
Fastware Error Messages .............................................................................................................................. 62
Beam Error Messages.................................................................................................................................... 68
Resources .......................................................................................................................................................... 69
Tutorials - Videos........................................................................................................................................... 69

User Manual –VisiPac & VisiTouch Series
VisiPac & VisiTouch Series –
User Manual
MAR.
2021
V1.0
5/69

User Manual –Visipac & VisiTouch Series
VisiPac & VisiTouch series –User Manual
MAR.
2021
V1.0
6/69
The users must have Read and Understood, but most of all must Respect the directives
described in this manual.
All people coming into contact with the machine on which the numerical control is installed,
whatever their function or whatever state the machine is in (assembly, disassembly, start-up,
production, maintenance, repairs) must have read and understood the requirements
concerning the security and the entirety of the directives of operation described in the
manuals delivered with the machine.
The operator must be properly trained to work with the machine on which the numerical
control is installed. Improper use of the numerical control can cause heavy damage on
equipment and/or injuries to people.
Modification of machine parameters can cause important material damage or lead to
irregular product quality.
Do not expose the numerical control to excessive humidity to avoid any risk of electrocution
and any deterioration of the equipment.
Make sure the numerical control is disconnected from the mains power before carrying out
any cleaning. Do not use liquids based on alcohol or ammoniac.
In case of malfunction of the numerical control, call a technician.
Do not expose the numerical control to direct sun rays or any other heat source.
Do not place the numerical control in the neighbourhood of magnetic equipment such as
transformers, motors or devices which generate interference (welding machines, etc.)
SAFETY
GENERAL SAFETY

User Manual –VisiPac & VisiTouch Series
VisiPac & VisiTouch Series –
User Manual
MAR.
2021
V1.0
7/69
While using this manual, you will come across the signs and icons represented here below:
they are directly related to the safety and security of persons. Carefully follow this advice and
inform others about it.
This warning sign appears in the manual whenever it is necessary to pay attention to rules,
instructions or advice. The correct sequence of operations is to be followed in order to avoid
damage to the machine. Symbolizes a serious personnel danger.
This warning sign appears in this manual whenever an important information needs to be
taken into consideration. Pay attention to this sign and follow the instructions given.
This sign appears in this manual whenever SETTING INSTRUCTIONS are given. Pay attention to
this sign and follow the sequence of instructions given.
This icon appears in this manual to give navigation information, to give the path to the subject
treated in the chapter.
General warning
Information
Settings
SIGNS AND ICONS APPEARING IN THIS MANUAL
Navigation

User Manual –Visipac & VisiTouch Series
VisiPac & VisiTouch series –User Manual
MAR.
2021
V1.0
8/69
Depending on software evolutions and the press brake controlled by the VisiTouch
(configuration/capabilities), the present manual may not fully correspond to the VisiTouch
that you currently have. However, differences are only minor.
This manual describes all features of
▪VisiTouch19_Press_PS_PC_V2.0 and above.
Touchscreens are pressure sensitive.
Do not press down hard on the screen.
Pressing hard on the screen will damage the display. Such damage is not covered by
manufacturer warranty!
Do not use sharp and/or pointed objects (sheet metal, screwdriver, metal pen ball, etc.) to
touch the screen; only use your fingers (with or without gloves on) or a plastic pen. Make sure
that your gloves do not have metal particles encrusted in the fingertips as they may also
damage the screen.
Take a few minutes to practice pressing gently on the screen, you will find that the screen is
very reactive, and it is pleasant to use.
GETTING STARTED WITH VISIPAC &VISITOUCH

User Manual –VisiPac & VisiTouch Series
VisiPac & VisiTouch Series –
User Manual
MAR.
2021
V1.0
9/69
SCREEN MAP
Punches
Punches
Dies
Dies
Correction Page
Extra Bending Parameters
Bend Graphic Page
Bend List Page
Bend Sequencing
Graphical Part
Extra Simulation Criteria
Main Page –Bend Numerical page
Menu –Next Page
Machine Status Page

User Manual –Visipac & VisiTouch Series
VisiPac & VisiTouch series –User Manual
MAR.
2021
V1.0
10/69
SCREEN MAP (CONTINUED)
Manual Page
User preference
Service Page
Transfer Page
Parameter Page
Information Page
Statistics page
Backup/Restore Page

User Manual –VisiPac & VisiTouch Series
VisiPac & VisiTouch Series –
User Manual
MAR.
2021
V1.0
11/69
The Menu button allows you to directly select (jump to) the desired screen. The content
of the menu changes contextually.
Briefly touching the Status pages zone gives access to the Status page. This is really a zone
that is active at any moment from any page.
Touching this zone for more than 2 seconds will activate the Semi-Automatic mode.
To clean the screen while the VisiTouch is on, touch the button.
Use only a damp and smooth cloth with soap or a neutral detergent.
NEVER use solvent, petrol, benzene, alcohols, etc.
GENERAL NAVIGATION
Add step or
next step
Status
Pages Zone
Menu button
Status Page Zone
Screen Cleaning
Menu Button
Bending Pages Buttons Configuration

User Manual –Visipac & VisiTouch Series
VisiPac & VisiTouch series –User Manual
MAR.
2021
V1.0
12/69
The Status page shows the status of all inputs and outputs and axes positions of the NC.
This feature is very useful during setup or during phone service with a machine installed in
the field.
This page is accessed from anywhere by pressing the Status Pages Zone.
To exit the Status page, press on the arrow on the left.
Axes have specific indicators. Their colour indicates the position of the axis relative to the
tolerance.
Possible states are:
•: Device not active and in the tolerance.
•: Device moving.
•: Device not active and outside of the tolerance.
STATUS PAGE
A cycle message may
appear indicating the
cycle phase the
machine is executing
Axis status indicator
Beam trace Button
Press arrow to
exit Status Page
Statistic Page Button

User Manual –VisiPac & VisiTouch Series
VisiPac & VisiTouch Series –
User Manual
MAR.
2021
V1.0
13/69
(Menu Button) → …→ User preference
To exit the User Preference page, touch the button.
To browse through the available languages, simply touch Language on the screen.
Available languages are:
•EN English.
•FI Suomi.
•RU Русский.
•BR Brazil.
•FR Français.
•SL Slovensko.
•CN 中文.
•IT Italiano.
•SV Svenska
•CZ Český.
•NL Nederlands.
•TR Türkçe.
•DE Deutsch.
•PL Polski.
•TW 台灣.
•ES Español.
•PT Português.
The list of available languages is subject to change and may increase over time.
USER PREFERENCES
Language

User Manual –Visipac & VisiTouch Series
VisiPac & VisiTouch series –User Manual
MAR.
2021
V1.0
14/69
This parameter allows choosing between mm, inch and none for the length unit to be used
in the VisiTouch.
When none is selected, the units used are millimetres.
This parameter allows choosing between ton, kN and tons for the force unit to be used in
the VisiTouch.
This parameter allows choosing between ton/m, kN/m and tons/ft for the force/length
unit to be used in the VisiTouch.
This parameter allows choosing between kg/mm2, N/mm2 and psi (*1000) for the sigma
unit to be used in the VisiTouch.
This function will display the axes positions on the Bend Numerical Page.
•When set to no, the position of axes Y1, X and R is displayed during the beam’s
movements.
•When set to yes1, the positions of the axes (Y1, Y2, X and R) are displayed during
their respective movements.
•When set to yes2, the positions of the axes (Y1, Y2, X and R) are constantly
displayed under their respective set-point values.
This parameter, when activated, lets the operator see the state of the part before and after
the bend in the Bend Sequencing page.
Length Units
Force Units
Force / Length
Units
Sigma Units
Show axes
position values
Show bent part

User Manual –VisiPac & VisiTouch Series
VisiPac & VisiTouch Series –
User Manual
MAR.
2021
V1.0
15/69
Touching Materials opens the Materials page, where the default characteristics for each
material can be changed, or a new material can be configured.
To be allowed to access the Materials page, a level 2 password is required.
The Materials page displays:
•Material: Selected material (here Steel).
•K Factor for the material (by default DIN6935).
•Default sigma: Default sigma for the material (here 45).
•Default thickness for the material.
•Thickness min/max: Determines the maximum and minimum accepted thickness
for the selected material.
•Three predefined default materials are available (steel, stainless steel, aluminium),
but others can be added
To add a material:
1. Touch and write the name of the new material.
2. Enter the new material’s characteristics.
To remove a material:
1. Select the material you want remove.
2. Touch and confirm the suppression of the material.
Materials

User Manual –Visipac & VisiTouch Series
VisiPac & VisiTouch series –User Manual
MAR.
2021
V1.0
16/69
By Pressing in the selected material is possible to set custom configuration
The Custom configuration page displays:
•Predefined Thickness: If activated is possible to set predefined thickness for the
material.
•Springback Correction If activated is possible to set corrections of the springback
effect of the material for different angles degrees.
•Thickness compensation factor: If activated is possible to set corrections of the
thickness effect of the material for different angles degrees.
This parameter allows the operator to apply a permanent correction to the Bottom Dead
Centre position.
Please note that this correction is always applied and is NOT shown in the
correction page. If you experience big differences from what you expect to get,
maybe check the value of this parameter.
This parameter allows the operator to choose on which side –Left of Right –he prefers to
have the side bar containing the Menu Button .
This parameter allows the operator to choose if he prefers to have the menu displayed at
the Bottom or at the Top of the screen when he presses the Menu Button .
BDC Correction
Menu horizontal
alignment
Menu vertical
alignment

User Manual –VisiPac & VisiTouch Series
VisiPac & VisiTouch Series –
User Manual
MAR.
2021
V1.0
17/69
When activated, this function clears the index and the machine will search for them, as
it does when turning the power on, allowing the operator to re-index its machine without
turning it off.
When this parameter is set to yes, it is possible to browse the USB key from the USB
transfer screen (see USB Transfer).
A USB key must be inserted.
Preferably use a specific USB key for transferring parts and VisiTouch Data
instead to use a generic memory stick full of data programs that are not relevant
for the numerical control.
When this parameter is set to yes, this small button is displayed on the Status page. By
activating/deactivating it, one can start and stop the recording of beam traces.
When activated, this function will open the beam trace screen automatically at the end of
the recording.
This parameter allows defining the default value displayed in the Extra Bending
Parameters when activating the back-gauge retraction function.
In TouchProfile Mode, when a retraction is necessary, the numerical control will
automatically calculate and activate the function. The calculated value can naturally
be manually modified.
Allows the user to set the time and date on the VisiTouch.
Clear indexation
USB Explorer
Default retraction
Set Clock
Use the up and down
arrows to modify the
selected field
Touch the field you
want to modify
Beam trace
Auto open beam
trace

User Manual –Visipac & VisiTouch Series
VisiPac & VisiTouch series –User Manual
MAR.
2021
V1.0
18/69
This function allows the calibration of the touch screen.
SETTING INSTRUCTIONS:
Simply follow the instructions on the page to calibrate the touchscreen.
Use your finger or the plastic tip of a pen to calibrate the Touchscreen. Never use
sharp objects as this will damage the screen.
When this parameter is set to yes, the Offset Pinch Point function is available in the Extra
Bending Parameters.
When this parameter is set to yes, the button up is available when the beam is not at
TDC.
Upward command
The beam goes up as long as the button is pressed.
Go to TDC max
The beam goes to TDC max
Go to next TDC
The beam goes to the next TDC. (first to programmed TDC, then
to the TDC max)
This parameter set the counting mode of the program quantity.
•Set to down, The counter will count from top to bottom
•Set to up, The counter will count from bottom to top
•Set to Autorelaod, The counter will automatically restart the counter once finish
•Set to Reset, The counter will need to be reset manually once finish
This function allows choosing the data entry mode for the back gauge on the Bend
Numerical Page or EasyBend Page. When set to yes, the length of the flange icon is
displayed by default. When set to no, the icon for the position in mm of the back gauge
is displayed.
When set to never, the position of the back gauge is no longer linked to the bending
angle, i.e. the position is never recalculated when the bending angle is modified.
The default value for this preference is never. Note that completely formatting
the machine will reset this preference to its default value.
The mode is not available for graphical parts (see also Set point back
gauge (X axis) / flange length).
Touchscreen
Calibration
Offset Pinch Point
function
Show button up
Show L first
Program counter
mode

User Manual –VisiPac & VisiTouch Series
VisiPac & VisiTouch Series –
User Manual
MAR.
2021
V1.0
19/69
This function allows choosing help during the indexation of the beam.
When this parameter is set to yes, during the Indexation of the beam, if the Index have not
been found, a pop-up with the instruction will appear and an interactive instruction will tell
to the operator the procedure to correctly Index the machine.
i.e. If the beam is not indexed and is actual position is upper then the Index.
When this parameter is set to yes, when a product is load from the library, or a modification
have been made in the part, it will not recalculate the axes and beam position.
When this parameter is set to yes, the down movement of the beam is stopped and the
beam is maintained in closed loop at pinch point during the retraction. The beam cycle will
resume as soon as the back gauge has finished its retraction.
This function allows choosing file destination for Parts and tools
By default the directories are in the Visitouch folder.
When set to New directory is possible to choose another folder destination i.e. if the
Numerical Control is related to the enterprise network is possible to share parts and tools
files from the same source.
Beam stop during
retractation
Indexation Aids
Disable
recalculation at
product load
Working
directories