CyberData 11107 Manual

Installation Quick Reference
Clock Kit Flush Mount Adapter for
Indoor Paging Speakers
011106*, RAL 9002, Gray White, Standard
011107, RAL 9003, Signal White, Optional
*Replaces the 011024 number.
Quick Reference 930350D © 2010, CyberData Corporation, ALL RIGHTS RESERVED© 2010, CyberData Corporation, ALL RIGHTS RESERVED 930350D Quick Reference
The Clock Kit enables the CyberData V2 VoIP Ceiling Speaker to be upgraded to a highly
visible public address device with a time display.
The large display characters are easily read and adjust for ambient light conditions. Time
sync is performed by NTP and a built-in real -time clock.
Power is supplied by the CyberData V2 Speaker from a single PoE connection.
The Clock Kit Flush Mount Adaptor Operations Guide is available as a PDF file at:
http://www.cyberdata.net/products/voip/digitalanalog/clockkit/docs.html
JP1
(1) Template for Wall Mount
Adapter and Screw Holes
(on placemat)
(1) Drywall Mounting Kit
(1) Flush Wall Mount Adapter
(4) 10-12 x 1.25-inch Pan Head
Phillips Screws
Install Jumper JP1 Prior to Installing the Clock Kit
Jumper Functions:
Jumper Function
JP1 Battery - Connect
JP2 Manufacturing - Open
JP3 Manufacturing - Open
JP4 Manufacturing - Open
JP5 Manufacturing - Open
Wall Mount Adapter Parts
Make sure that jumper JP1 is installed prior to installing the Clock Kit (see the picture on the right). Installing JP1 powers
the Real Time Clock from the battery. If you do not install JP1, the clock will lose it's time when the power is disconnected.
(4) #10 Plastic Ribbed Anchor
Moving the Clock Connector Cover Plate
Connecting Power (optional power injector)
1. Unscrew and remove the two attachment cover screws.
2. Remove the clock connector cover plate and and rotate it
180 degrees to the left.
3. Screw and tighten the cover screws to secure the cover
plate in place (as shown in the picture).
Cover plate
Device
Ethernet
Optional power injector
(CyberData # 010867A)
To N e t w o r k
Corporate Headquarters
CyberData Corporation
2555 Garden Road
Monterey, CA 93940, USA
Phone: [phone]
Fax: [phone]
www.CyberData.net
Sales: [phone] ext. 334
Support: 831-373-2601 ext. 333
Email: [e-mail]
RMA Dept: [phone] ext. 136
Email: [e-mail]
Warranty information available at:
http://www.CyberData.net/index.html
Contacting CyberData
Connecting Power (PoE)
To Po E Networ k

DRYWALL
CUTOUT
Step 1
Step 2
Step 3
CyberData Part #011098 or #011099
Step 1
Step 2Step 4
ATLAS FEST-18SC Enclosure
Part Number 611038
12.6 [320] 2.7 [69]
14.2 [360]
PM LED
Ambient light detector
Mounting
Features
Dimensions
(sold separately by ATLAS, and not included with the Clock Kit)
(1) ATLAS FEST-18SC
(sold separately)
(2) ATLAS Sound FEST
Mounting Bracket
(sold separately)
(4) No.10 Nut with tooth washer
(comes with the ATLAS wall mount)
(4) No.10-32 x 0.375-inch Pan
Head Phillips Machine Screw
(comes with the ATLAS wall mount)
ATLAS FEST-18SC Enclosure Parts
Note: All ATLAS parts are sold separately by ATLAS,
and are not included with the Clock Kit Adapter
(3) 8-32 x 1 1/4” Mounting
Screws (from the Ceiling
Speaker Drop Ceiling
Mounting Kit)
Use three 8-32 x 1 1/4” MOUNTING SCREWS
(from the Ceiling Speaker Drop Ceiling
Mounting Kit) to install the Version 2 Speaker
into the flush mount clock kit.
Install part number 611038 through the pre-cut
drywall into the Atlas sound enclosure.
3.
4.
Assemble the ATLAS® FEST-18SC enclosure.2.
If you do not have the ATLAS enclosure, then
use the TEMPLATE on this document to drill
four holes in the wall for the anchors and screws.
1.
To mount a Clock Kit Flush Mount Adapter:
Route the Network cable into either the
top, bottom, or side knockouts (KO).
Ground Lug
Step 3