CyberData 11182 Manual

The IP Endpoint Company
Installation Quick Reference
Singlewire-enabled Push-to-Talk
V2 Ceiling Speaker
011182, RAL 9002, Gray White, Standard
011183, RAL 9003, Signal White, Optional
Quick Reference 930462C © 2015, CyberData Corporation, ALL RIGHTS RESERVED© 2015, CyberData Corporation, ALL RIGHTS RESERVED 930462C Quick Reference
4.00 [101.6]
120°
VoIP Speaker
Mounting Template
Speaker Hole Diameter:
7.50 [190.5]
Screw Hole Diameter:
0.1875 [4.75]
Dimensions are in inches [millimeter]
The Singlewire-enabled Push-to-Talk V2 Ceiling Speaker is compatible with InformaCast Version 8.1 and higher.
Typical System Installation
Getting Started
• Download the Singlewire-enabled Push-to-Talk V2 Ceiling Speaker Operations Guide PDF file from the Documentation
page at:
http://www.cyberdata.net/products/voip/digitalanalog/singlewirespeakerptt/docs.html
• Create a plan for the locations of your speakers.
• Prior to installation, consult local building and electrical code requirements.
Parts
Parameter Factory Default Setting
IP Addressing DHCP
IP Addressa
a. Default if there is not a DHCP server present.
10.10.10.10
Web Access Username admin
Web Access Password admin
Subnet Maska255.0.0.0
Default Gatewaya10.0.0.1
802.3af Compliant Ethernet Switch
IP Phone
12 34 56
IP Talkback InformaCast ServerIP SpeakerRemote Call Button
Speaker
(1) Template for Speaker
and Screw Holes*
(1) Speaker Assembly (1) Drop Ceiling Mounting Kit
(3) #8 Nylon Thumb Nuts
(3) #8 Fender Washers
(3) 8-32 x 1 1/4” Mounting
Screws
(1) Drywall Mounting Kit
(3) Plastic Ribbed Anchors
(3) #8 Sheet Metal Screws
* See the last page of this document

© 2015, CyberData Corporation, ALL RIGHTS RESERVED 930462C Quick Reference Quick Reference 930462C © 2015, CyberData Corporation, ALL RIGHTS RESERVED
Mounting
Contacting CyberData
*Ceiling Tile or Dry Wall
VoIP V2 Speaker
Assembly
#8 Fender Washer (3x)
#8 Nylon Thumb Nut (3x)
#6 Screw (3x)
Dry Wall Mounting Kit
Template
Plastic Ribberd Anchor (3x)
Dry Wall Mounting Kit
#8-32x1 1/4" (3X)
Ceiling Mounting Screw
*Optional Reinforcement Mount
P/N: 010991A (Sold Seperately)
Tools Required for Installation:
• (1) Sheetrock saw or
(1) Drywall cutter
• (1) #2 Phillips Screwdriver or
(1) #2 Phillips Screwdriver Hex Bit
To mount a speaker:
1. Use the TEMPLATE on the back of this
document to cut a hole in the wall or ceiling,
and prepare holes for the screws.
2. Plug the Ethernet cable into the speaker
assembly. The yellow light verifies the
network connection.
3. For drop ceiling mounting, position the IP
SPEAKER ASSEMBLY in the ceiling so
that its screw holes align with those you
prepared.
4. For drywall mounting, place the three
PLASTIC RIBBED ANCHORS in the holes
you prepared, and position the IP
SPEAKER ASSEMBLY over them, aligning
the screw holes in the assembly with the
anchors.
5. For drop ceiling mounting*, use the three
8-32 x 1 1/4" MOUNTING SCREWS, #8
NYLON THUMB NUTS, and #8 FENDER
WASHERS to secure the speaker.
For drywall mounting, use the three #8
SHEET METAL SCREWS to secure the
speaker.
* For weak ceiling tile, CyberData offers a
reinforcing mount (CyberData part number
010991A).
Speaker
Assembly
Sales: [phone] ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: [phone] ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: [phone]
Fax: [phone]
http://www.cyberdata.net/
Dimensions and Connections
Connecting Power
Features
9.0 [229]
3.0 [75]
Dimensions are in Inches [Millimeter]
AUX SPEAKER (-)
AUX SPEAKER (+)
GND
LINE OUT (-)
LINE OUT (+)
BUTTON LED (-)
BTN SENSE
BUTTON LED (+)
RELAY NO
RELAY COM
AUX POWER (-)
AUX POWER (+)
(+12VDC @ 1A)
J10 J9
CLASS II WIRING
PoE Injector (Part #010867A)
Non PoE Switch
802.3af switch Class "0"
RTFM Switch
To broadcast a device’s current IP address, press and
release the RTFM switch within a five second window.
To restore a device’s factory default settings, press and
hold the RTFM switch for more than five seconds.
Speaker Volume
Network Link/Activity LED (yellow)
Speaker Status LED (green)
A solid light confirms that the speaker is operational.
Microphone