CyberData 011216 Manual

Quick Reference 931558B © 2022, CyberData Corporation, ALL RIGHTS RESERVED© 2022, CyberData Corporation, ALL RIGHTS RESERVED 931558B Quick Reference
Wall Mounting Options
Gang Box Mounting Options
Contacting CyberData
Backplate
Wall
Mounting
Screw (3x)
(Not Provided)
Network Cable &
for Ground Wire Connection
Pick One of Four Mounting Hole
Screw
121001A
Accessory Kit
(4 Places) on Wall
Pre Drill Holes
Ground Wire
Cutout
Slot
Entry
Cable
Closed
Slots
Cable
Two Gang Box use four
Wall Cutout
or Two Gang Box
Backplate accept
Single Gang Box
Single Gang Box use two
Backplate
Wall Cutout
121002B
Screw Accessory Kit
Mounting
Screw (3x)
(Not Provided)
Ground Wire
Any Available Mounting Hole
Ground Wire Connect to
(Not Provided)
Network Cable
Slot
Entry
Cable
Closed
Slots
Cable
Sales: 831-373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: https://support.cyberdata.net/
RMA Department Contact and Status: https://support.cyberdata.net/
Warranty Information: https://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: [phone]
Fax: [phone]
https://www.cyberdata.net/
Typical System Installation
Getting Started
• Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
https://www.cyberdata.net/products/011216
• Create a plan for the locations of your Office Ringers.
• WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
• WARNING: This enclosure is not rated for any AC voltages!
Parts
Parameter Factory Default Setting
IP Addressing DHCP
IP Addressa
a. Default if there is not a DHCP server present.
IPv4 Link Local
Web Access Username admin
Web Access Password admin
Subnet MaskaIPv4 Link Local
Default GatewayaIPv4 Link Local
802.3af Compliant Ethernet Switch
SIP Office Ringer IP Phone IP PBX ServerSIP Office Ringer SIP Office Ringer
*More installation and mounting
options are available in the
Operations Guide.
(4) #6 x 1.25-inch
Sheet Metal Screw
(4) Plastic ribbed anchor (4) 6-32 x 0.5-inch flat
undercut Phillips machine
screw
(1) Office Ringer Assembly (1) Wall Mounting Kit (1) Gang Box Mounting Kit
The IP Endpoint Company
Installation Quick Reference
SIP Office Ringer
SIP Compliant
011216

© 2022, CyberData Corporation, ALL RIGHTS RESERVED 931558B Quick Reference Quick Reference 931558B © 2022, CyberData Corporation, ALL RIGHTS RESERVED
RTFM Button
Terminal Block Connections
Plug in the Network Cable and Create Service Loop
RTFM button (SW1)
When the device is operational and linked to a network,
you can use the Reset Test Function Management
(RTFM) button (SW1 [see picture]) to announce the
device’s IP address or restore the device to the factory
default settings.
To announce the device’s current IP address:
• Press and release the RTFM button within a five
second window.
Note The device will use DHCP to obtain the new IP
address (DHCP-assigned address or default to
IPv4 Link Local if a DHCP server is not
present).
To restore the device to factory default settings:
• Press and hold the RTFM button for longer than five
seconds until you hear the device announce that it is
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
*Contacts 1 and 2 on the terminal block are only for powering the
device from a non-PoE 12VDC power source as an alternative to
Network PoE power. Use of these contacts for any other purpose will
damage the device and void the product warranty.
34
1
8
Wire (IN)
Tin Leads
Approx. 1/4” or
6mm
Terminal Block
can accept 16 AWG wire
Use a 3.17 mm (1/8-inch) flat blade
screwdriver for the terminal block screws
Two (2)
Cable Entry Slot
Two (2)
Cable Entry Slot
One (1)
Cable Entry Slot
Mounting
Screw (3x)
Create
Service Loop
Before Closing
Network
Connector
Network Cable
Backplate
Faceplate
Assembly
When Use in
Auxiliary Strobe
P/N: 011288A
(Sold Separately)
Conjunction with
Dimensions
Dimensions for Wall Mounting and One / Two Gang Box Mounting
4.53 [115.0]
4.53 [115.0]
DIMENSIONS ARE IN INCHES [MILLIMETER]
2.14 [54.3]
Dimensions Are in Inch [Millimeter]
Ø0.188 [Ø4.8]
Ø0.189 [Ø4.8]
0.910 [23.1]
3.400 [86.4]
3.280 [83.3]
3.400 [86.4]
1.820 [46.2]
Through Hole
Through Hole
82° Countersunk
= Slot Open
= Slot Close
Fits One/Two Gang Box
(6 Places)
*
*
*
3.150 [80.0]
2.895 [73.5]
(4 Places)
Cut Hole for Cable Through