CyberPower HT705UC User manual

Copyright © 2017 Cyber Power Systems (USA), Inc. All rights reserved.
CONGRATULATIONS ON YOUR PURCHASE
Thank you for selecting the CyberPower HT705UC
Premium Surge Protector. The information contained in
this manual explains the features and operation of the
HT705UC. Please take a few moments to read this manual.
FEATURES
1. ON/OFF Reset Control Switch and Circuit Breaker
Controls power to all outlets. The switch is also a 15A
breaker. When an overload occurs, it will automatically
switch o. To resume operation, ensure the overload
condition is removed and reset the surge protector by
switching the unit ON.
2.
3.
4.
5.
Firestop Design Advanced Metal-Oxide Varistor
(MOV) with Built-In Fuses
Encased component dissipates surge events and
potential flame, sparks and heat.
Wrapped Cord and Right Angle Plug
Easy to coil;kink and abrasion resistant cord with
low profile right angle plug for easy cord
management. Advanced Protection - Surge
Protected LED Illuminated when protection is
working properly. Clean Power - Ground LED
Illuminated when properly grounded.
6. Seven Outlets
6 standard and 1 transformer spaced outlets
7. USB Charging Ports*
Connect and charge up to 2 USB devices using the
surge protected USB charging ports.
*USB outlets cannot be used as a USB hub. This device
does not transfer data.
8. Coaxial Cable Protection
Protects coaxial lines from surges and spikes.
SPECIFICATIONS
•Model Number: HT705UC
•Outlets: 6 standard and 1 transformer spaced outlets
•USB Charging Rating: 5V/3.1A total
•Power Cord Length: 5 ft
•Surge Protection: 3,480 Joules
•Electrical Rating: 125V/15A/1875W
•UL Clamping Voltage: UL 1449 3rd/500V (L-N, L-G, L-G)
•Maximum Peak Current: 105,000A
•3 AC Lines Protected: H-N: 75,000A, H-G: 15,000A,
N-G: 15,000A (The maximum surge possible on
household Wiring is 6,000 volts)
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK - Use only
in dry locations and only indoors. DO NOT plug into
another relocatable power tap. DO NOT “daisy chain”
surge protectors. DO NOT use with any aquarium
equipment. DO NOT use if properly grounded outlets are
not available. DO NOT install this device if there is not at
least 10 meters (30 feet) or more of wire between the
electrical outlet and electrical service panel. This device
features an internal protection that will disconnect the
surge protective component at the end of its useful life,
but will maintain power to the load – now unprotected.
TROUBLESHOOTING
If the grounded indicator does not light when you plug in
the surge protector, move the surge protector to a
dierent grounded three-prong AC outlet. If it still does
not light, return the product to dealer for assistance. If
the surge protector proves to be working properly, your
outlets may not be a properly grounded and need to be
repaired by a professional electrician. If the grounded
indicator turns o after a period of use, the surge
protection has been depleted. Replace your surge
protector. If the protected indicator does not light, the
surge protector’s AC lines is no longer protected from
surge. The surge protector may have received a power
surge or spike beyond its specified limits that overloaded
the protection circuitry and rendered it inactive. The
surge protector has protected your connected
equipment as designed, but it will not protect against
future surges & spikes and should be replaced.
TECHNICAL SUPPORT
Please contact our Tech Support department with
installation, troubleshooting, or general product questions.
• Phone: [phone]
• Email: [e-mail]
• Hours of Operation:
Monday – Friday 7:00am – 6:00pm CST
USER’S MANUAL
7-Outlet Surge Protector
HT705UC
7-Outlet Surge Protector
HT705UC
12
3.1A
4
5
6
ADVANCED
PROTECTION
POWER
CLEAN
1
2
7
8
3
•Response Time: Less than 1 nanosecond
•Attenuation: Up to 43dB
•EMI/RFI Filtration: 150 kHz to 100 MHz
•Circuit Breaker: Resettable 15 Amp

LIMITED WARRANTY AND CONNECTED
EQUIPMENT GUARANTEE
Read the following terms and conditions carefully before
using the CyberPower HT705UC (the “CPS Product”). By
using the CPS Product, you consent to be bound by the
terms and conditions of this Limited Warranty and
Connected Equipment Guarantee (together referred to as
this “Warranty”). IF YOU DO NOT AGREE TO THE TERMS
AND CONDITIONS OF THIS WARRANTY, YOU SHOULD
RETURN THE PRODUCT FOR A FULL REFUND PRIOR TO
USING IT.
Who is providing this Warranty, what does it cover?
Cyber Power Systems (USA), Inc. (“CyberPower”) provides
this Limited Warranty. It only covers the original purchaser
and ends if you no longer own the CPS Product. This
warranty covers defects in materials and workmanship in the
CPS Product under normal use and conditions. It also covers
equipment connected to the CPS Product and damaged
because of the failure of the CPS Product. This warranty
covers the CPS Product and connected equipment for as
long as you own the CPS Product.
How do you open a connected equipment claim?
1. Call us at [phone] or write to us at Cyber Power
Systems (USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN
55379, or send us an e-mail message at [e-mail]
for instructions, within 10 days of the occurrence.
2. When you contact CyberPower, identify the Product, the
Purchase Date, and the item(s) of Connected Equipment.
Have information on all applicable insurance or other
resources of recovery/payment that are available to the
Initial Customer and Request a Claim Number.
3. You must provide a dated purchase receipt (or other proof
of the original purchase) for the Cyber Power unit and
connected equipment. You also need to provide a
description of the damage to your connected equipment.
4. Pack and ship the product to CyberPower and, if
requested, the item(s) of Connected Equipment, a repair
cost estimate for the damage to the Connected
Equipment, and all claim forms that CyberPower provides
to you. Show the Claim Number on the shipping label or
include it with the product. You must prepay all shipping
costs, you are responsible for packaging and shipment,
and you must pay the cost of the repair estimate.
What will CyberPower do to correct problems?
CyberPower will inspect and examine the CPS Product. If the
CPS Product is defective in material or workmanship,
CyberPower will repair or replace it at CyberPower’s
expense, or CyberPower will refund the full purchase price
you paid for the CPS Product (purchase receipt showing
price paid is required). If the CPS Product failed to protect
any equipment plugged into it, we will also send you forms
for making your claim for the connected equipment. We will
repair or replace the equipment that was damaged because
of the failure of the CPS Product or pay you the fair market
value (NOT REPLACEMENT COST) of the equipment at of
the time of the damage. We will use Orion Blue Book,
another third-party valuation guide, eBay, craigslist, or other
source to establish that amount. Our maximum liability is
limited to $800,000 for the HT705UC.
Who pays for shipping?
We pay when we send items to you; you pay when you send
items to us.
What are some things this Warranty does not cover?
1. THIS WARRANTY DOES NOT COVER ANY SOFTWARE
THAT WAS DAMAGED OR NEEDS TO BE REPLACED DUE
TO THE FAILURE OF THE CPS PRODUCT OR ANY DATA
THAT IS LOST AS A RESULT OF THE FAILURE OR THE
RESTORATION OF DATA OR RECORDS, OR THE
REINSTALLATION OF SOFTWARE.
2. This Warranty does not cover: misuse, modification,
operation or storage outside environmental limits of the
CPS Product or the equipment connected to it, or for
damage while in transit or in storage, nor if there has been
improper operation or maintenance, or use with items not
designed or intended for use with the CPS Product, such
as laser printers, appliances, aquariums, medical or life
support devices, etc.
What are the other limitations?
The sole and exclusive remedies of the Initial Customer are
those provided by this Warranty.
1. This Warranty does not apply unless the CPS Product and
the connected equipment were connected to properly
wired and grounded outlets (including compliance with
electrical and safety codes of the most current electrical
code), without the use of any adapters or other connectors.
2. The CPS Product must have been plugged directly into the
power source and the equipment connected to the CPS
Product must be directly connected in the CPS Product,
not “daisy-chained” together in serial fashion with any
extension cords, another Product or device similar to the
CPS Product, surge suppressor, or power tap. Any such
installation voids the Warranty.
3. The CPS Product and connected equipment must have
been used properly in a suitable and proper environment,
in conformance with any applicable license, instruction
manual, or warnings.
4. The CPS Product must have been used at all times within
the limitations on the CPS Product’s VA capacity. This device is manufactured using environmentally-safe
procedures in compliance with the Restriction of
Hazardous Substances (RoHS) directive.
Please join CyberPower in caring for the
environment by recycling this manual.
3 4
Where can I get more information?
Contact CyberPower at 4241 12th Ave E., STE 400, Shakopee,
MN 55379; call us at [phone]; or send us an e-mail
message at [e-mail].
PRODUCT REGISTRATION
Prompt product registration assures coverage under the
Limited Warranty, and also allows the opportunity to be notified
of product enhancements, upgrades, and other announcements.
Registration is quick and easy. Go to Product Registration
page at www.cyberpowersystems.com/registration.
CONTACT INFORMATION
Cyber Power Systems, Inc. 4241 12th Avenue East Suite 400
Shakopee, MN 55379
Toll-free: 1-877-297-6937 | CyberPowerSystems.com
CONFORMANCE APPROVALS
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference. (2) This device must accept
any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment. This Class B
digital apparatus complies with Canadian ICES-003.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
K01-0000632-00
www.cyberpowersystems.com
© 2017 Cyber Power Systems (USA), Inc. All rights reserved.
All other trademarks are the property of their respective owners.