CyberPower CSP606U42A User manual

CONGRATULATIONS ON YOUR PURCHASE
Thank you for selecting the CyberPower CSP606U42A
Surge Protector. This manual explains the features and
operation of the CSP606U42A. Please take a few
moments to read this manual.
FEATURES
1. ON/OFF Reset Switch Breaker
Controls power to all outlets. The switch is also a 15 A
breaker. When an overload occurs, it will automatically
switch o. To resume operation, ensure the overload
condition is removed and reset the surge protector by
switching the unit ON.
2. Surge Protected Indicator
Illuminated when the surge protection feature is
working properly.
3. Standard Grounded Outlets (6)
4. USB Charging Ports* (2)
Connect and charge up to two (2) USB devices using
the surge protected USB charging ports.
*USB outlets cannot be used as a USB hub. This device
does not transfer data.
5. Low-Profile Right-Angle Plug
6. Safe-fail Protection
Power is cut to connected equipment when the unit
can no longer provide surge protection.
SPECIFICATIONS
• Model Number: CSP606U42A
• Outlets: Standard Grounded Outlets (6), USB Charging
Ports (2)
• USB Charging Rating : 5 V/4.2A total
• Surge Protection: 900 Joules
• Electrical Rating: 125 V/15 A/1875 W
• UL Clamping Voltage: UL 1449 4th/500 V (L-N, L-G, N-G)
• Maximum Peak Current: 45,000 A
• 3 AC Lines Protected:
L-N: 15,000A
L-G: 15,000A
N-G: 15,000A
The maximum surge possible on household wiring is
6,000 volts)
• Response Time: Less than 1 nanosecond
• Circuit Breaker: Resettable 15 Amp
• Plug Type: Low-Profile, Right-Angle Plug
• Cord Length: 6 ft
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK - Use only in
dry locations and only indoors. DO NOT plug into another
relocatable power tap. DO NOT “daisy chain” surge
protectors. DO NOT use with any aquarium equipment.
DO NOT use if properly grounded outlets are not
available. DO NOT install this device if there is less than 10
meters (30 feet) or more of wire between the electrical
outlet and electrical service panel. DO NOT use for
medical or life support equipment. This device features an
internal protection that will disconnect the surge
protective component at the end of its useful life, but it
will maintain unprotected power to the load. If this
situation is undesirable for the application, follow the
manufacturer’s instructions for replacing the device.
TROUBLESHOOTING
▪If the ON/OFF is switched OFF, the 15 Amp circuit
breaker may have tripped. Examine your connected
equipment and remove the device that is overloading the
circuit. Then, turn the ON/OFF switch back to RESET.
▪If the protected indicator does not light, the surge
protector’s AC lines are no longer protected from surge.
The surge protector may have received a power surge or
spike beyond its specified limits that overloaded the
protection circuitry and rendered it inactive. The surge
protector has protected your connected equipment as
designed, but it will not protect against future surges,
and spikes. It should be replaced.
TECHNICAL SUPPORT
Please contact our Tech Support Department with
installation, troubleshooting, or general product questions.
• Phone: [phone]
• Email: [e-mail]
• Hours of Operation:
Monday – Friday 7:00am – 6:00pm CST
USER MANUAL
8-Outlet Surge Protector
(6 AC & 2 USB Ports)
CSP606U42A
8-Outlet Surge Protector
(6 AC & 2 USB Ports)
CSP606U42A
12
Copyright © 2019 Cyber Power Systems (USA), Inc. All rights reserved.
1
3
4
PROTECTED
USB 4.2A
5
2

3 4
K01-0000693-01
LIMITED WARRANTY AND CONNECTED
EQUIPMENT GUARANTEE
Read the following terms and conditions carefully before
using the CyberPower CSP606U42A (the “product”). By
using the product, you consent to be bound by the terms
and conditions of this limited warranty and connected
equipment guarantee (together referred to as this
“warranty”). IF YOU DO NOT AGREE TO THE TERMS AND
CONDITIONS OF THIS WARRANTY, YOU SHOULD RETURN
THE PRODUCT FOR A FULL REFUND PRIOR TO USING IT.
Who is providing this warranty, and what does it cover?
Cyber Power Systems (USA), Inc. (“CyberPower”) provides
this limited warranty. It only covers the original purchaser
and ends if you no longer own the product. This warranty
covers defects in materials and workmanship in the product
under normal use and conditions. It also covers equipment
connected to the product damaged because of the failure of
the product. This warranty covers the product and
connected equipment for as long as you own the product.
How do you open a connected equipment claim?
1. Call us at [phone], or write to us at:
Cyber Power Systems (USA), Inc.
4241 12th Avenue East, Suite 400
Shakopee, MN 55379,
or send us an email at [e-mail] within 10 days
of the occurrence for instructions.
2. When you contact CyberPower, identify the product, the
purchase date, and the item(s) of connected equipment.
Have information on all applicable insurance or other
resources of recovery/payment that are available to the
initial customer, and request a claim number.
3. You must provide a dated purchase receipt (or other proof
of the original purchase) for the CyberPower unit and
connected equipment. You also need to provide a
description of the damage to your connected equipment.
4. Pack and ship the product to CyberPower and the item(s)
of connected equipment, a repair cost estimate for the
damage to the connected equipment, and all claim forms
that CyberPower provides to you. Show the claim number
on the shipping label, or include it with the product. You
must prepay all shipping costs. You are responsible for
packaging and shipment, and you must pay the cost of
the repair estimate.
What will CyberPower do to correct problems?
CyberPower will inspect and examine the product. If the
product is defective in material or workmanship, CyberPower
will replace it at CyberPower’s expense, or CyberPower will
refund the full purchase price you paid for the product
(purchase receipt showing price paid is required). If the
product failed to protect any equipment plugged into it, we
will also send you forms for making your claim for the
connected equipment. We will replace the equipment that
was damaged because of the failure of the product or pay
you the fair market value (NOT REPLACEMENT COST) of
CONTACT INFORMATION
Cyber Power Systems (USA), Inc.
4241 12th Avenue East, Suite 400
Shakopee, MN 55379
Toll-free: 1-877-297-6937 | CyberPowerSystems.com
the equipment at of the time of the damage. We will use Orion
Blue Book, another third-party valuation guide, eBay, Craigslist,
or other source to establish that amount. Our maximum liability
is limited to $75,000 for the CSP606U42A.
Who pays for shipping?
We pay shipping when we send items to you; you pay when
you send items to us.
What are some things this Warranty does not cover?
1. THIS WARRANTY DOES NOT COVER: ANY SOFTWARE THAT
WAS DAMAGED, SOFTWARE THAT NEEDS TO BE REPLACED
DUE TO THE FAILURE OF THE PRODUCT, OR ANY DATA THAT
IS LOST AS A RESULT OF THE FAILURE. THIS WARRANTY
DOES NOT COVER THE RESTORATION OF DATA OR
RECORDS, OR THE REINSTALLATION OF SOFTWARE.
2. This warranty does not cover: misuse, modification, operation
or storage outside of the environmental limits of the product
or the equipment connected to it. It does not cover damage
while in transit or in storage; if there has been improper
operation or maintenance, or use with items not designed or
intended for use with the product, such as laser printers,
appliances, aquariums, medical, or life support devices, etc.
What are the other limitations?
The sole and exclusive remedies of the initial customer are
those provided by this warranty.
1. This warranty does not apply unless the product and the
connected equipment were connected to properly wired and
grounded outlets (including compliance with electrical and
safety codes of the most current electrical code), without the
use of any adapters or other connectors.
2. The product must have been plugged directly into the power
source. The equipment connected to the product must be
directly connected in the product, not “daisy chained”
together in serial fashion with any extension cords, another
product, or device similar to the product, surge suppressor,
or power tap. Any such installation voids the warranty.
3. The product and connected equipment must have been used
properly in a suitable environment, in conformance with any
applicable license, instruction manual, or warnings.
4. The product must have been used at all times within the
limitations on the product’s maximum rated wattage.
Where can I get more information?
Contact us at:
Cyber Power Systems (USA), Inc.
4241 12th Avenue East, Suite 400
Shakopee, MN 55379;
Call us at [phone];
Send us an email message at [e-mail].
PRODUCT REGISTRATION
Prompt product registration assures coverage under the limited
warranty, and also allows the opportunity of notifications for
product enhancements, upgrades, and other announcements.
Registration is quick and easy. Go to the Product Registration
Page at CyberPowerSystems.com/registration.
This device is manufactured using environmentally-safe procedures in
compliance with the Restriction of Hazardous Substances (RoHS) directive.
Please join CyberPower in caring for the environment by recycling.
CyberPowerSystems.com
© 2019 Cyber Power Systems (USA), Inc. All rights reserved.
All other trademarks are the property of their respective owners.
UL Listed to U.S. and Canadian Safety Standards UL 1449. This product
is listed to applicable U.S. and Canadian safety standards by
Underwriters Laboratories Inc.
WARNING: This product can expose you to chemicals including styrene (ABS),
which is known to the State of California to cause cancer.
For more information, go to www.P65Warnings.ca.gov.
CONFORMANCE APPROVALS
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
WARNING: Changes or modifications not expressly approved
by the party responsible for compliance could void the user's
authority to operate the equipment.