CyberPower P600WUHD User manual

Copyright © 2020 Cyber Power Systems, Inc. All rights reserved.
CONGRATULATIONS ON YOUR PURCHASE
Thank you for selecting the CyberPower P600WUHD
Surge Protector. The information contained in this
document explains the features and operation of the
P600WUHD. Please take a few moments to read this
manual.
6-Outlet Wall Tap
Surge Protector with USB
P600WUHD
USER MANUAL
1 2
FEATURES
SPECIFICATIONS
1. Standard Spaced Outlets (6)
2. USB Charging Ports (2)
3. USB Output: 5V/3.4A (shared)
• Model Number: P600WUHD
• Outlets: 6 Standard Outlets
•USB Ports: 2 USB Type-A
•USB Output: 5V/3.4A (shared)
• Surge Protection: 500 Joules
• Electrical Rating: 125V/15A/1875W
• UL Clamping Voltage: UL 1449 3rd/800V (H-N),
• Maximum Peak Current: 15,000A
•Attenuation: Up to 32dB
•EMI/RFI Filtration: 150 kHz to 100 MHz
•Connected Equipment Guarantee: $15,000
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK - Use only in
dry locations and only indoors. DO NOT plug into another
relocatable power tap. DO NOT “daisy chain” surge
protectors. DO NOT use with any aquarium equipment.
DO NOTuse if properly grounded outlets are not
available. DO NOTinstall this device if there is not at least
10 meters (30 feet) or more of wire between the electrical
outlet and electrical service panel. This device features an
internal protection that will disconnect the surge
protective component at the end of its useful life, but will
maintain power to the load – now unprotected.
TECHNICAL SUPPORT
Please contact our Tech Support department with
installation, troubleshooting, or general product questions.
• Phone: [phone]
• Visit: CyberPowerSystems.com/support
• Hours of Operation:
Monday – Friday, 7:00am – 6:00pm CST

K01-E00O017-02
43
LIMITED WARRANTY AND
CONNECTED EQUIPMENT GUARANTEE
Read the following terms and conditions carefully before using
the CyberPower P600WUHD (the “CPS Product”). By using the
CPS Product, you consent to be bound by the terms and
conditions of this Limited Warranty and Connected Equipment
Guarantee (together referred to as this “Warranty”). IF YOU DO
NOT AGREE TO THE TERMS AND CONDITIONS OF THIS
WARRANTY, YOU SHOULD RETURN THE PRODUCT FOR A
FULL REFUND PRIOR TO USING IT.
Who is providing this Warranty, what does it cover?
Cyber Power Systems (USA), Inc. (“CyberPower”) provides this
Limited Warranty. It only covers the original purchaser and ends
if you no longer own the CPS Product. This warranty covers
defects in materials and workmanship in the CPS Product under
normal use and conditions. It also covers equipment connected
to the CPS Product and damaged because of the failure of the
CPS Product. This warranty covers the CPS Product and
connected equipment for as long as you own the CPS Product.
How Do You Open a Connected Equipment Claim?
What will CyberPower do to correct problems?
CyberPower will inspect and examine the CPS Product. If the CPS
Product is defective in material or workmanship, CyberPower will
repair or replace it at CyberPower’s expense, or CyberPower will
refund the full purchase price you paid for the CPS Product
(purchase receipt showing price paid is required).
If the CPS Product failed to protect any equipment plugged into
it, we will also send you forms for making your claim for the
connected equipment. We will repair or replace the equipment
that was damaged because of the failure of the CPS Product or
pay you the fair market value (NOT REPLACEMENT COST) of the
equipment at of the time of the damage. We will use Orion Blue
Book, another third-party valuation guide, eBay, craigslist, or
other source to establish that amount. Our maximum liability is
limited to $15,000 for the P600WUHD.
Who pays for shipping?
We pay when we send items to you; you pay when you send items
to us.
What are some things this Warranty does not cover?
1. THIS WARRANTY DOES NOT COVER ANY SOFTWARE THAT
WAS DAMAGED OR NEEDS TO BE REPLACED DUE TO THE
FAILURE OF THE CPS PRODUCT OR ANY DATA THAT IS LOST
AS A RESULT OF THE FAILURE OR THE RESTORATION OF
DATA OR RECORDS, OR THE REINSTALLATION OF
SOFTWARE.
2. This Warranty does not cover: misuse, modification, operation
or storage outside environmental limits of the CPS Product or
the equipment connected to it, or for damage while in transit
or in storage, nor if there has been improper operation or
maintenance, or use with items not designed or intended for
use with the CPS Product, such as laser printers, appliances,
aquariums, medical or life support devices, etc.
What are the other limitations?
The sole and exclusive remedies of the Initial Customer are those
provided by this Warranty.
1. This Warranty does not apply unless the CPS Product and the
connected equipment were connected to properly wired and
grounded outlets (including compliance with electrical and
safety codes of the most current electrical code), without the
use of any adapters or other connectors.
2. The CPS Product must have been plugged directly into the
power source and the equipment connected to the CPS
Product must be directly connected in the CPS Product, not
“daisy-chained” together in serial fashion with any extension
cords, another Product or device similar to the CPS Product,
surge suppressor, or power tap. Any such installation voids the
Warranty.
3. The CPS Product and connected equipment must have been
used properly in a suitable and proper environment, in
conformance with any applicable license, instruction manual, or
warnings.
4. The CPS Product must have been used at all times within the
limitations on the CPS Product’s VA capacity.
Where can I get more information?
Contact CyberPower at 4241 12th Ave E., STE 400, Shakopee, MN
55379; call us at [phone]; or send us an e-mail message at
[e-mail].
PRODUCT REGISTRATION
Prompt product registration assures coverage under the Limited
Warranty, and also allows the opportunity to be notified of
product enhancements, upgrades, and other announcements.
Go to Product Registration at www.cyberpower.com
CONTACT INFORMATION
Cyber Power Systems (USA), Inc.
4241 12th Avenue East Suite 400 Shakopee, MN 55379
Toll-free: 1-877-297-6937 | CyberPower.com
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Note: These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device is manufactured using environmentally-safe
procedures in compliance with the Restriction of Hazardous
Substances (RoHS) directive.
Please join CyberPower in caring for the environment by
recycling this manual.
© 2020 Cyber Power Systems (USA), Inc.
All rights reserved. All other trademarks are the property of
their respective owners.
1. Call us at [phone] or write to us at Cyber Power Systems
(USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN 55379, or
send us an e-mail message at [email protected] for
instructions, within 10 days of the occurrence.
2. When you contact CyberPower, identify the Product, the
Purchase Date, and the item(s) of Connected Equipment. Have
information on all applicable insurance or other resources of
recovery/payment that are available to the Initial Customer and
Request a Claim Number.
3. You must provide a dated purchase receipt (or other proof of
the original purchase) for the CyberPower unit and connected
equipment. You also need to provide a description of the
damage to your connected equipment.
4. Pack and ship the product to CyberPower and, if requested, the
item(s) of Connected Equipment, a repair cost estimate for the
damage to the Connected Equipment, and all claim forms that
CyberPower provides to you. Show the Claim Number on the
shipping label or include it with the product. You must prepay
all shipping costs, you are responsible for packaging and
shipment, and you must pay the cost of the repair estimate.