DEFINITIONS FOR ILLUMINATED LED INDICATORS
Power
ON
Using
Battery
AVR
Over
Load
Wiring
Fault
Alarm CONDITION
On Off Off Off Off Off Normal
Off On Off Off On/Off Two
Beeps
Utility Failure- The UPS is providing power to battery power
supplied outlets.
Off On Off Off On/Off Rapid
Beeps
Utility Failure- The UPS is providing battery power. Rapid
beeps indicate the unit will run out of power shortly.
Off Off Off On On/Off Long
Beep
System Overload- Occurs when connected equipment
exceeds the rating of unit. Turn the UPS off, unplug at least
one piece of equipment, wait 10 seconds, reset the circuit
breaker and turn the unit on.
Off Off Off On On/Off Long
Beep
Battery Overload- Occurs when connected equipment exceeds
the rating of battery outlets of the unit. Turn the UPS off,
unplug at least one piece of equipment from battery outlets, wait
10 seconds, reset the circuit breaker and turn the unit on.
On Off On Off On/Off Off
AVR Mode-Max. boost 12% of input voltage for output
regulation while input voltage is from 17% to 26% under
nominal.
On/Off On/Off On/Off Off On None
Electrical Wiring Fault- This indicates a wiring problem with
the AC outlet such as bad ground, missing ground, or reversed
wiring. User is advised to disconnect all electrical equipment
from the outlet and have an electrician check the outlet to insure
proper wiring.
Limited Warranty and Connected Equipment Guarantee
In purchasing a CP900AVR / BC900 CP1200AVR / BC1200 CP1500AVR / BC1500 in the United States or Canada, the original end user
receives a Limited Warranty and Connected Equipment Guarantee from Cyber Power Systems (USA), Inc. (for ease of reading, referred to
as "CyberPower"). The Limited Warranty and the Connected Equipment Guarantee are intended to be the original end-user's exclusive
rights and remedies. The Limited Warranty and the Connected Equipment are separate, all though they are related.
Limited Warranty. The original end user (referred to as the "Initial Customer") receives an express limited warranty (referred to as the
"Limited Warranty") for the CP900AVR / BC900 CP1200AVR / BC1200 CP1500AVR / BC1500 purchased from CyberPower (referred to as
the "Product"). The Limited Warranty is for the Product itself. The terms of the Limited Warranty are explained below.
Connected Equipment Guarantee. CyberPower also provides the Initial Customer with protection in the event that the Product is not free
from defects in materials and workmanship, and certain equipment connected to the Product is damaged (the "Connected Equipment
Guarantee"). The Connected Equipment Guarantee protects the Initial Customer for damage to equipment plugged into the Product.The
terms of the Connected Equipment Guarantee are explained below.
The Limited Warranty and the Connected Equipment Guarantee are subject to the terms set forth below. Additionally, State or Provincial law
may adjust the terms of the Limited Warranty or the Connected Equipment Guarantee or the State or Province may impose additional
obligations, or additional "implied warranties." To the extent necessary to comply with those laws, the terms of the Limited Warranty and the
Connected Equipment Guarantee should be read to adjust to those requirements only to the extent necessary to comply with such local law.
If you are an Initial Customer, you are asked to read the following terms and conditions carefully before using the Product. By using the
Product you consent to be bound by and become a party to the Limited Warranty and Connected Equipment Guarantee. If you do not agree
to the terms and conditions of the Limited Warranty and Connected Equipment Guarantee, you should return the Product for a full refund
prior to using it. REGISTRATION
CyberPower requests that you complete and return the Warranty Registration Card enclosed with the Product or register the Product at its
website (www.cyberpowersystems.com) to establish that you are the Initial Customer of the Product, and therefore entitled coverage under
the Limited Warranty and the Connected Equipment Guarantee. (Registration is not required for Limited Warranty coverage, but note if you
do not complete a registration card you will be required to provide proof of purchase, as described below, to have the benefits of this Limited
Warranty.) LIMITED WARRANTY
CyberPower warrants to you, the Initial Purchaser, that the Product will be free from defects in material and workmanship for three years
from the date of original purchase, subject to the terms of this Limited Warranty.
Any Implied Warranty of Merchantability or for Fitness for a Particular Purpose, if applicable to the Product, is limited in duration to the period
of ownership by the Initial Customer. This provision shall NOT create any Implied Warranty or Merchantability or of Fitness for a Particular
Purpose that would not otherwise apply to the Product. NOTE: Some States do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you.
To be covered you must still be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty.
Exclusive Remedies Under Limited Warranty.
Your exclusive remedy and CyberPower's' sole obligations are as follows for the Product:
If (a) the CyberPower Product you purchased and still own is defective in material or workmanship under this Limited Warranty or any
applicable warranty imposed by law, and
(b) all Limited Warranty requirements have been met, CyberPower will repair or replace the
Product if it proves to be defective in material or workmanship during the Warranty Period.
Making a Limited Warranty Claim.
To make a Limited Warranty claim on a Product, you must do the following:
1. Complete and return the CyberPower Warranty Registration Card, or provide reasonable proof of purchase (for example, a sales receipt)
that establishes you as the Initial Customer (the original end-user consumer purchaser) of the Product and prove that the Product was
purchased within three (3) years of the event for which you want to make a claim for warranty service.
3. When you contact CyberPower, identify the Product, the Purchase Date, and request Return Materials Authorization (RMA) information
from CyberPower.
4. Pack and ship the Product to CyberPower as instructed in your RMA. Show the RMAcode on the shipping label or include it with the
Product. You MUST prepay all shipping costs and you are responsible for packaging and shipment.
CyberPower will inspect and examine the Product within ten (10) days of receipt. If the Product is not as warranted, CyberPower will repair
or replace the Product and return it to you at CyberPower's expense, or, if CyberPower is unable to or decides not to repair or replace the
Product (if defective) within a reasonable time, CyberPower will refund to you the full purchase price you paid for the Product (purchase
receipt showing price paid is required). CONNECTED EQUIPMENT GUARANTEE
If you are the Initial Purchaser and the Product is still covered by the Limited Warranty, the Connected Equipment Guarantee provides
protection for damage to equipment connected to the Product ("Connected Equipment"), subject to certain terms and limitations.
The Connected Equipment Guarantee is not "first dollar" coverage. It is secondary. If you have any other source of payment for your loss,
such as insurance, another warranty, or an extended warranty or purchase protection plan (“Primary Coverage”), CyberPower’ will pay only
to the extent that that the Primary Coverage does not cover the loss. CyberPower's obligation is reduced by any amounts that you are
entitled to recover from the Primary Coverage, whether or not you make a claim for recovery under any applicable Primary Coverage.
The Limited Warranty does not cover Connected Equipment, but as is explained below, to be covered under the Connected Equipment
Guarantee, the Connected Equipment must have been damaged due to a failure of the Product. The Connected Equipment must have been
damaged due to a defect in materials or workmanship of the Product
In the event of damage to the Connected Equipment, your exclusive remedies, and CyberPower’s sole obligations, are as follows for
Connected Equipment. If (a) the Product purchased and owned by you is defective in material or workmanship; (b) the Limited Warranty
requirements have been met (except that the three year limitation of the Limited Warranty does not limit the Connected Equipment
Guarantee, which is for the lifetime of the Product), and; (c) none of the limitations or exclusions on warranty coverage apply (or than the
three year limit), CyberPower will (as CyberPower elects, as permitted by law), repair, replace, or pay the Agreed Damage Amount (defined
below) for, the item(s) of your electronic equipment directly and properly connected to the product (the "Connected Equipment") if that
Connected Equipment is (x) damaged by AC power line transients, spikes, or surges on properly installed, grounded, and code-compliant
120 volt power lines in the United States and Canada, or by transients, surges or spikes on standard telephone equipment lines, or Base
10/100T Ethernet lines that are properly installed and connected (a "Power Disturbance") and (y) is directly plugged into and properly
connected to a CyberPower Product in its original condition which is properly operated when a Power Disturbance passes through the
CyberPower Product and (y.1) exhausts the protection capacity of the CyberPower Product or (y.2) damages the CyberPower Product. This
provision sets out the only liability of any character of CyberPower for direct, indirect, special, consequential, and/or incidental damages
under our Limited Warranty, applies only to Connected Equipment, and all such Liability is limited to theAgreed Damage Amount.
Making a Connected Equipment Guarantee Claim.
To make a Warranty claim for damage to Connected Equipment under the Connected Equipment Guarantee, you must do the following:
1. Complete and return the CyberPower Warranty card or provide reasonable proof of purchase, for example, a sales receipt that
establishes you as the original end-user consumer purchaser of the Product.
3. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have information on all
applicable insurance or other resources of recovery/payment that are available to the Initial Customer and the name of the power utility
supplier for the location of the Connected Equipment and Request a Claim Number.
4. Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the damage to
the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the shipping label or include it
with the product. Initial Customer shall prepay all shipping costs, must pay the cost of the repair estimate, and is responsible for
packaging and shipment.
CyberPower’s Duties.
CyberPower will inspect and examine the Product and the item(s) of Connected Equipment (or at CyberPower's election, your written
statement and repair cost estimate for those item(s)). You must return the product for inspection.
If the damage to Connected Equipment is covered by the Connected Equipment Guarantee, CyberPower will (in addition to Limited
Warranty remedies for the CyberPower Product itself) repair (or paythe costs of repair) or replace the Connected Equipment or, at the option
of CyberPower, as permitted by law, pay to the Initial Customer the "Agreed Damage Amount" (up to the aggregate limits stated below) for
all item(s) of Initial Customer's Connected Equipment. The "Agreed Damage Amount" for all items of Initial Customer's Connected
Equipment shall be the lesser of the amount determined under Clause (1) or (2) below, reduced by any amounts described in Clause (3)
below:
1. The fair market value of the Connected Equipment as established by the lower of (a) the price list of Orion Blue Book on the date of
occurrence (or if such price list is no longer published, a published or announced price list reasonably selected by CyberPower), or (b) the
average price the same or similar items are being sold for on
E-bay, or (c) the lowest price the same or similar items can be purchased for in the United States; or
2. The aggregate ceiling amount for all Connected Equipment: CyberPower CP900AVR / BC900 - $300,000.00. CP1200AVR / BC1200 -
$375,000.00. CP1500AVR / BC1500 - $500,000.00.
3. The amount(s) of all payment you have or are entitled to receive from insurance, other warranties, extended warranties, or from other
sources or persons for the Connected Equipment or damage to such equipment so that CyberPower’s maximum liability shall be reduced to
reflect all such other payments or sources of recovery
If CyberPower replaces the connected equipment or pays to the Initial Customer the Agreed Damage Amount, the Initial Customer shall
transfer ownership of all item(s) to CyberPower without warranty by the Initial Customer, but free of lien or other interest.
CONDITIONS COMMON TO THE LIMITED WARRANTY AND THE CONNECTED EQUIPMENT GUARANTEE
The Limited Warranty and the Connected Equipment Guarantee are the only and the exclusive express warranty of CyberPower with
respect to the Product. This exclusion of other express warranties applies to written and oral express warranties.
LIMITATION: THE LIMITED WARRANTY AND THE CONNECTED EQUIPMENT GUARANTEE DOES NOT COVER
The Limited Warranty and the Connected Equipment Guarantee are intended to exclusive rights and remedies and replace any other rights,
to the extent allowed by law.
1. As to the CyberPower Product, the limited warranty does not cover or apply to: misuse, modification, operation or storage outside
environmental limits for the Products, in transit, in shipment, or in storage, damage or deterioration, improper operation or maintenance, or
use with items or equipment not designed or intended for use with the product.
2. As to Connected Equipment, the Connected Equipment Guarantee covers only damage within the specific terms of the Connected
Equipment Guarantee to Connected Equipment (and only up to the applicable aggregate ceiling amount).
3. The Connected Equipment Guarantee does not cover damage to Connected Equipment or apply if the Product has been operated in a
failure mode or not in compliance with CyberPower operatinginstructions and manuals, or if the Connected Equipment has beenoperated in
a failure mode or not in compliance with the instructions and manuals of its manufacturer/vendor.
The Limited Warranty and the Connected Equipment Guarantee Do Not Apply Unless The Initial Customer:
1. Has properly connected the Product and the Connected Equipment to properly wired and grounded outlets (including compliance with
electrical and safety codes of the most current electrical code (ANS/NFPA 70), without the use of any adapters, extension cords or other
connectors.
2. Has provided a suitable and proper environment for use and installation of the Product and Connected Equipment.
3. Has properly installed and operated the CyberPower Product and Connected equipment.
4. Has operated the Product at all times within the limitations on the Product’s VA capacity as stated in this User Manual.
CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following:
1. Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software.
2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and code-compliant 120
volt power lines in the United States and Canada; transients, surges or spikes on standard telephone land lines, PBX telephone equipment
lines or Base 10T Ethernet lines, when properly installed and connected. (This exclusion applies, for example, to fluctuations in data
transmission or reception, by CATV or RF transmission or fluctuations, or by transients in such transmission.
3. Damage from any circumstance described as excluded above with respect to the product.
4. Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of either the product or
the Connected Equipment.
Exclusion of Consequential and Other Damages.
The sole and exclusive remedies of the Initial Customer are those provided by the Limited Warranty and Connected Equipment Guarantee.
CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee. CyberPower
excludes any liability for direct, indirect, special, incidental or consequential damages, whether for damage to or loss of property [EXCEPT
FOR (AND ONLY FOR) the specific limited agreement of CYBERPOWER to provide certain warranty benefits regarding "Connected
Equipment" under the "CYBERPOWER Connected Equipment Guarantee"], loss of profits, business interruption, or loss of information or
data. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation may not apply to you.
DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT OR OTHER HIGH RISK ACTIVITIES.
CyberPower does not sell the Products for use in high-risk activities. The Product is not designed or intended for use in hazardous
environments requiring fail-safe performance, including the operation of nuclear facilities, aircraft navigation or communication systems, air
traffic control, weapons systems, life support or medical applications or for use in any circumstance in which the failure of the Product could
lead directly to death, personal injury, or severe physical or property damage, or that would affect operation or safety of any medical or life
support device (collectively, "High RiskActivities"). CyberPower expressly disclaims any express or implied warranty of fitness for High Risk
Activities. CyberPower does not authorize use of any of its products use in any High RiskActivities.
ANY SUCH USE IS IMPROPER AND IS A MISUSE OF CYBERPOWER PRODUCTS.
The Limited Warranty and the Connected Equipment Guarantee are governed by the laws of the United States and the State of Minnesota,
without reference to conflict of law principles. The application of the United Nations Convention of Contracts for the International Sale of
Goods is expressly excluded.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorientor relocate the receiving
antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help. Any special
accessories needed for compliance must be specified in the instruction.
CAUTION: Ashielded-type power cord is required in order to meetFCC emission limits and also to prevent interference to the nearby radio
and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to
this equipment.
CAUTION: Any changes or modifications not expressly approved by the guarantee of this device could void the user’s authority to operate
the equipment.
