CYP CDPS-44SM User manual

CDPS-44SM
HDMI 4x4 Seamless Matrix Switcher
Operation Manual
Operation Manual

DISCLAIMERS
The information in this manual has been carefully checked and is be-
lieved to be accurate. Cypress Technology assumes no responsibility
for any infringements of patents or other rights of third parties which
may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no com-
mitment to update or to keep current the information contained in
this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, tran-
scribed, stored in a retrieval system, or any of its part translated into
any language or computer le, in any form or by any means—elec-
tronic, mechanical, magnetic, optical, chemical, manual, or other-
wise—without express written permission and consent from Cypress
Technology.
© Copyright 2012 by Cypress Technology.
All Rights Reserved.
Version 1.0 January 2012
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 21/09/26 Preliminary Release
RDV2 17/04/13
RDV3 04/06/13 Matrix mode 1080i@50/60 IN4
Disabled

CONTENTS
1. Introduction........................................... 1
2. Applications.......................................... 1
3. Package Contents ............................... 1
4. System Requirements........................... 1
5. Features................................................. 2
6. Operation Controls and Functions...... 3
6.1 Front Panel ....................................... 3
6.2 Rear Panel........................................ 5
6.3 Remote Control............................... 6
6.3.1 Remote Control Dip Switch......... 7
6.4 RS-232 Protocols .............................. 7
6.5 RS-232 & Telnet Commands........... 8
6.6 RS-232 & Telnet control................. 10
6.7 Telnet Setting ................................. 11
6.8 OSD MENU...................................... 11
7. Connection Diagram ......................... 15
8. Specications ..................................... 16
9. Timing .................................................. 17
9.1 Input Support Timing ..................... 17
9.2 Output Support Timing ................. 18

1
1. INTRODUCTION
The 4 by 4 HDMI Seamless Matrix Switcher allows the signal from 4 dif-
ferent input sources to be freely selected and arranged on 4 displays
(TV or monitor), providing three output modes (Matrix, Dual and TV
Wall) for various applications. Matrix mode routes the source signals
to output displays as regular matrix does, Dual mode allows 2 sets of
2 selected sources to show on designate output displays with POP
method and TV Wall mode extends a selected source to display on
all 4 output displays as one. The device supports video timings up to
WUXGA@60RB and 1080p@60Hz, audio format up to 7.1CH LPCM at
192kHz sampling rate based on input source EDID. For all the opera-
tion/control can be done through IR, remote control, Telnet, RS-232 or
front panel buttons.
2. APPLICATIONS
• Broadcasting room and control
• Surveillance room and control
• Public advertisement and control
• Digital Presentation
• Conference call or meeting room presentation
3. PACKAGE CONTENTS
• 1 x 4 by 4 Seamless Matrix Switcher
• 1 x Remote Control (CR-125)
• Software CD Driver (Optional)
• 1 x 12V/3A DC Power Adaptor
• Operation Manual
4. SYSTEM REQUIREMENTS
Input source equipments such as DVD/Blu-ray players or any video
signal and PC/Notebook devices and output HD TV/monitor.

2
5. FEATURES
• HDMI, HDCP1.1 and DVI compliant
• Deep color support 8/10/12 bit source
• Seamless switching
• Supports three different modes: Matrix mode/ Dual mode/ TV Wall
mode
■ Matrix mode: Can routes and output any 4 source to any 4 dis-
plays with seamless switching
Note: Under output timing 1080i@50/60 input 4 will be disabled,
OSD will show “IN 4 Disabled”
■ Dual mode: Can display POP (Picture Of Picture) image com-
bined by 2 sources to be presented on the HDMI output ports
(Dual A and Dual B)
■TV Wall mode: Can output any source to 4 displays (2 by 2
Video wall) as a full image with adjustable Bezel Correction for 4
displays
• Supports OSD, RS232, Telnet, Remote control and on-panel controls
• Input resolutions support VGA~WUXGA and 480i~1080p
• Output resolutions support 480p~1080p
• Supports different input resolution and output resolution selectable
from OSD menu. The factory default value for the output resolution
is 720p@60Hz/ 2CH LPCM
• Audio supports LPCM 2CH, 6CH, 8CH/AC3/DTS/Dolby Digital Plus/
Dolby TruHD & DTS-HD

3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER - +
1
INPUT 234SAVERECALL
A
OUTPUT BCD
4X4 SEAMLESS MATRIX CDPS-44SM
LOCK
MATRIX/
DUAL/WALL
XGA
720P
MENU
1 2 3 4 5 8 9
6 7
1IR Window:
Accept IR signal from the device’s remote control included in the
package.
2Power
 ON/OFF: Press this button to power on the device or set it to
standby mode.
 Factory default: Press Power then connect power supply to
reset the system to Factory default setting.
3MENU:
Press this button to bring up the OSD menu on screen.
Press “MENU” with “-“button to switch output timing to 720P@60Hz
instantly.
Press “MENU” with “+” button to switch output timing to XGA
(1024x768@60Hz) instantly.
4-/+ Buttons:
Press these buttons to scroll down/up the OSD selections then press
“MENU” button to conrm.
5CHANNEL INPUT 1~4 and CHANNEL OUTPUT A~D:
 Matrix mode:
i. Press “Matrix/Dual/Wall” button to switch to Matrix mode and
LED will illuminate constantly.
ii. Press an output from A~D and then press corresponding input
from 1~4. For example: press output A then press input 1,
output A will display input 1’s image. Each output setting must
be made individually.

4
 Dual mode: To combine 2 sources to be presented on each
HDMI output ports (Dual A and Dual B).
i. Press “Matrix/Dual/Wall” button to switch to Dual mode and
LED unilluminate.
ii. Press output A/B and then press corresponding input 1/2. For
example: press output A then press input 1, output A will
display input 1’s image on the left side, then press output B
and then press input 2, output A will display input 2’s image
on the right side. Both output A and B will have identically
image.
iii. Dual A group are output A and B, Dual B group are output C
and D. Each group will output the same image
simultaneously.
iv. Press button A or B for 3 seconds, to switch Dual A channel’s
audio between output A or B.
v. Press button C or D for 3 seconds, to switch Dual B channel’s
audio between output C or D.
TV Wall mode:
i. Press “Matrix/Dual/Wall” button to switch to TV Wall mode
and LED will blink constantly.
ii. Press input 1~4 to select a source to 4 displays (2 by 2 Video
wall). The audio will be on output A only.
6MATRIX/DUAL/WALL:
Press to switch between Matrix mode, Dual mode and TV Wall
mode. When in Matrix mode the LED will illuminate constantly,
when in DUAL mode the LED will unilluminate and when in TV Wall
mode the LED will blink constantly.
7LOCK:
Press once to lock the keypad and remote control, press 3 second
again to release the lock function.
8SAVE:
To save the customized input and output corresponding settings.
 Press “Matrix/Dual/Wall” button to select mode status.
 Press each output channel A~D and then press corresponding
input channel 1~4.
 Press “SAVE”, the input 1~4 LEDs will all illuminate at the same

5
time, then press input 1/2/3 or 4 to save to the system memory.
For example: Select Matrix mode, press output A then press
input 4, then press “SAVE”. This will corresponding to remote
control FAV.1~FAV.4.
9RECALL:
When in the mode status “Matrix, Dual or Wall”, press “RECALL”
and the input channel 1~4 LED will illuminate at the same time,
and select input channel 1/2/3 or 4 to recall the customized
screen settings and this will corresponding to remote control
FAV.1~FAV.4.
6.2 Rear Panel
4321 DCBACONTROL
RS232 DC 12V
USB
SERVICE
ONLY
HDMI IN HDMI OUT
1 2 3 4 5 6
1HDMI IN 1~4:
Connect with HDMI source equipments such as DVD/Blue-ray play-
ers and or PC/Notebook devices.
2HDMI OUT 1~4:
Connect with HDMI TV/Monitor/Recorder for output image display
or saving.
3Control:
Connect to an active network for telnet control (Please refer to 6.5
telnet Commands).
4USB SERVICE ONLY:
This slot is reserved for factory use only.
5RS-232:
Connect from PC/Notebook with D-Sub 15pin cables for RS-232
command sending and controling over the device.
6DC 12V:
Plug the 12V DC power supply into the unit and connect the
adaptor to an AC outlet.

6
6.3 Remote Control
1Power: Press this button to
switch on the device or press
it again to set it to standby
mode.
2Info: Press this button to show
the device’s rmware version.
3Out A~D and In 1~4: Press out-
put A~D and then press input
1~4 to select display input.
For example: press Out A then
press In 1, output A will display
input 1’s image.
4MATRIX/DUAL/WALL: Press to
switch between Matrix mode,
Dual mode and TV Wall
mode.
5Lock: Press once to lock the
keypad and remote control,
press 3 second again to re-
lease the lock function.
6Mute: Press this button to
mute the audio from HDMI
output port.
7▲/▼/←/→/OK: Press these buttons to scroll through the OSD selec-
tion and press OK to enter and conrm the setting.
8Exit: Press this button to exit the OSD menu or the OSD settings.
9Menu: Press this button to enter into the OSD menu.
10 1024x768/720p/1080p: Press these hot keys to switch between
each resolution.
11 AL/AR/BL/BR: When in Dual mode, press these hot keys to switch
the audio channel in Left or Right side for Dual A and Dual B
group.
12 SAVE:To save the customized input and output corresponding
settings.
CR-125
OK
Out AIn 1Matrix
Out B
Info Power
In 2 Dual
Out C In 3 TV Wall
LockOut D In 4
Mute
Exit Menu
Save1024x768 FAV.1
720p 1080p FAV.2
AL AR FAV.3
BL
Dual Audio
BR FAV.4
2
3
6
8
10
11
1
4
5
9
13
7
12

7
 Press “Matrix/Dual/Wall” button to select mode status.
 Press each output channel A~D and then press corresponding
input channel 1~4.
 Press “SAVE”, then input 1~4’s LED will illuminate at the same
time, then press remote control FAV.1~FAV.4 to save to the
system memory.
13 FAV.1~FAV.4:
Press favorite hot keys 1~4 to bring up the customized screen save
settings.
6.3.1 Remote Control Dip Switch
Open Remote control back cover to adjust dip-switch ON/OFF to
match IR address setting in the OSD menu. Factory defualt is on 0.
1 2
ON
0
1 2
ON
1
1 2
ON
2
1 2
ON
3
6.4 RS-232 Protocols
CDPS-44SM
►
◄
Remote Controller(PC)
PIN Assignment PIN Denition
1 NC 1 NC
2TxD 2RxD
3RxD 3TxD
4 NC 4 NC
5GND 5GND
6 NC 6 NC
7 NC 7 NC
8NC 8NC
9 NC 9 NC
Baud Rate: 115200bps
Data Bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1

8
6.5 RS-232 & Telnet Commands
All commands will be not executed unless followed with a carriage
return (0x0D) and commands are case-sensitive.
Command Active CDPS-44SM Return
AUA001 Dual A Audio channel in Left side AUA001
AUA002 Dual A Audio channel in Right side AUA002
AUA999 Check Dual A audio channel status AUA???
AUB001 Dual B Audio channel in Left side AUB001
AUB002 Dual B Audio channel in Right side AUB002
AUB999 Check Dual B audio channel status AUB???
AUD000 Audio output Off AUD000
AUD001 Audio output On AUD001
AUD999 Check audio on/off status AUD???
AUE000 Audio edid is LPCM 2CH AUE000
AUE001 Audio edid is LPCM 6CH AUE001
AUE002 Audio edid is LPCM 8CH AUE002
AUE003 Audio edid is BITSTREAM AUE003
AUE004 Audio edid is HD AUE004
AUE999 Check audio edid setting AUE???
BEZ000 Bezel Correction OFF BEZ000
BEZ001 Bezel Correction ON BEZ001
BEZ999 Check bezel correction on/off status BEZ???
BEH??? Horizontal (H) Bezel correc-
tion???=000 ~ Maximum
BEH???
BEH998 Check the current Horizontal(H) Bezel
correction Maximum value
BEH???
BEH999 Check the current Horizontal(H) Bezel
correction setting value
BEH???
BEV??? Vertical (V) Bezel correction???=000
~ Maximum
BEV???
BEV998 Check the current Vertical(V) Bezel
correction Maximum value
BEV???
BEV999 Check the current Vertical(V) Bezel
correction setting value
BEV???
BRI??? Setting Brightness No response
???=000~100 for matrix mode
???=(000~100)+200*(OUT No.-1) for dual/tv wall mode
For example: OUT B set the Brightness value to 57
=(57)+200*(2-1) = 257
BRI99?Check current Brightness value BRI???
99?=999 for matrix mode
99?=991~994=OUT1~4 for dual/tv wall mode
CAL??? RECALL FAV. ???=001~004=FAV.1~4 CAL???

9
CON??? Setting Contrast No response
CON999 Command setting same as Bright-
ness(BRI)
CON???
EGW999 RS232 only, check current Ethernet
Gateway Address
aaa.bbb.ccc.ddd
EIP999 RS232 only, check current Ethernet IP
Address
aaa.bbb.ccc.ddd
EMK999 RS232 only, check current Ethernet
Subnet Mask Address
aaa.bbb.ccc.ddd
HUE??? Setting HUE No response
HUE999 Command setting same as Brightness
(BRI)
HUE???
INP??? INPUT selection???=001~004=IN 1~4 INP???
Execute OUT???
INP999 Check current INPUT INP???
LCK000 Un-lock LCK000
LCK001 Lock LCK001
LCK999 Check current Lock/un-lock status LCK???
MNE001 OSD Menu EXIT No response
MND001 OSD Menu DOWN No response
MNL001 OSD Menu LEFT (-) No response
MNO001 OSD Menu OK No response
MNR001 OSD Menu RIGHT (+) No response
MNU001 OSD Menu UP No response
MNX001 OSD Menu No response
MOD001 Matrix mode MOD001
MOD002 Dual mode MOD002
MOD003 TV Wall mode MOD003
MOD999 Check current output mode status MOD???
OUT??? OUTPUT selection???=001~004=OUT
A~D
OUT???
OUT999 Check current OUTPUT OUT???
PWR000 Power Off(Standby) PWR000
PWR001 Power On PWR001
PWR999 Check current power status PWR???
RES??? Output resolution???=001~ ...corre-
sponding osd menu list
RES???
RES999 Check current output resolution RES???
RST001 Factory Reset RST001
RST002 Picture Reset RST002
SAT??? Setting Saturation No response
SAT999 Command setting same as Brightness
(BRI)
SAT???
SAV??? SAVE FAV. ???=001~004=FAV.1~4 SAV???

10
VER999 Check rmware version VER???
Example:
VER110=V1.1
6.6 RS-232 & Telnet control
Using PC software or Hyper terminal to congure the setting. This soft-
ware application can be downloaded from the product webside.
Simply control panel:
Full function control panel:

11
6.7 Telnet Setting
Through TCP/IP protocol, to sent Port 23 for Telnet communication.
From OSD menu or through RS-232 command to check Telnet con-
nection behavior.
6.8 OSD MENU
Main Menu Sub Menu Adjustments Default
PICTURE
(*1)
ALL
CONTRAST 0 ~ 100 50
BRIGHTNESS 0 ~ 100 50
SATURATION 0 ~ 100 50
HUE 0 ~ 100 50
DUAL
DUAL AL
DUAL AR
DUAL BL
DUAL BR
TV WALL
OUT A
OUT B
OUT C
OUT D
D/T
RESET
ALL
RESET ALL
EXIT

12
OUTPUT RESOLUTION 480p, 576p, 720p50,
720p60, 1080i50(*2),
1080i60, 1080p24,
1080p50, 1080p60,
1024x768, 1280x800,
1280x1024,
1366x768, 1440x900,
1600x900, 1600x1200,
1680x1050,
1920x1200
720p60
EXIT
AUDIO EDID
(*3)
LPCM 2CH, LPCM
6CH,
LPCM 8CH, BIT-
STREAM,
HD
LPCM
2CH
EXIT
OSD SETTINGS POSITION LEFT T, RIGHT T,
LEFT B, RIGHT B
LEFT T
H OFFSET 0 ~ 20 10
V OFFSET 0 ~ 20 10
TRANSPARENCY 0 ~ 9 4
MENU TIMEOUT 5 ~ 50, OFF(*4) 8
INFO.TIMEOUT 5 ~ 50, OFF 8
INFO.DISPLAY ON, OFF ON
BRIEF INFO ON, OFF OFF
EXIT
HDCP INPUT(*5) ACCEPT, NOT
ACCEPT
ACCEPT
OUTPUT(*6) FOLLOW INPUT,
ALWAYS ON
FOLLOW
INPUT
EXIT

13
BEZEL CORRECTION
(*7)
CORRECTION ON, OFF OFF
H CORRECTION 0 ~ by output
resolution
0
V CORRECTION 0 ~ by output
resolution
0
EXIT
RECALL / SAVE
(*8)
RECALL CANCEL, FAV.1
~ 4
CANCEL
SAVE CANCEL, FAV.1
~ 4
CANCEL
EXIT
ETHERNET IP MODE DHCP, STATIC DHCP
STATIC SET IP, MASK, GATE IP
BYTE1 192
BYTE2 168
BYTE3 5
BYTE4 155
RE-LINK(*9)
TIMEOUT (Min.)(*10) 5~60, OFF 10
EXIT
OTHERS IR ADDRESS(*11) 0 ~ 3 0
EXIT
FACTORY DEFAULT
EXIT
YES, NO NO
EXIT
INFORMATION
(*12)
IN/OUT RESOLUTION,
SOURCE HDCP/AU-
DIO,
OUT MODE, FIRM-
WARE VER
EXIT
EXIT

14
Note:
*1 Picture:
In Matrix mode, four pictures adjust simultaneously.
In Dual/TV Wall mode, each picture can adjust individual and
support individual
last memory feature.
*2 Output:
In Matrix mode only support 1080i@50Hz and 1080i@60Hz
*3 AUDIO EDID:
Embedded input audio EDID contents,
LPCM 2CH = LPCM 2CH
LPCM 6CH = LPCM 2CH/ 6CH
LPCM 8CH = LPCM 2HC/ 6CH/ 8CH
BITSTREAM = LPCM 2CH, AC3, DTS
HD = LPCM 2CH/ 6CH/ 8CH, AC3, DTS, Dolby Digital Plus, DTS-HD
*4 TIMEOUT =OFF means MENU and INFO will continue showing on the
screen
*5 HDCP INPUT:
ACCEPT: Support HDCP source, this is normal source setting
NOT ACCEPT: Not support HDCP source. For example: Apply source.
*6 HDCP OUTPUT:
FOLLOW INPUT: If source with HDCP the output will support HDCP. If
input source without HDCP the output will not support HDCP. When
in Dual mode, one of each side (Left or Right) support HDCP, the
output will support HDCP.
ALWAYS ON: All the TV/Monitor need to support HDCP, to avoid
switching source from non-HDCP to HDCP, the ashing image or no
image.
*7 BEZEL CORRECTION:
Only support in TV Wall mode, after adjustment the system will sup-
port last memory function.
*8 SAVE/RECALL:
To SAVE/RECALL input/ouput setting, the system support last memory
function to save all the setting.
*9 Ethernet RE-LINK:
After the setup, need to RE-LINK the system and re-connect the
system again.
*9 Ethernet TIMEOUT:
Select OFF to end the time out function or when telnet is under idol
without sending commands within the time out setting the telnet

15
system will be terminated.
*10 IR ADDRESS:
This setting is to match the IR remote control dip switch. Please ref-
ered to 6.31.
*11 INFORMATION:
To show Input/Output/Audio/Mode/Firmware information.
7. CONNECTION DIAGRAM
4321 DCBACONTROL
RS232 DC 12V
USB
SERVICE
ONLY
HDMI IN HDMI OUT
AB
CD
A
ABAB
CDCD
Set-top Box HDMI Video signal
HDMI
Cable
TV/Display TV/Display
HDMI
Cable
HDMI
Cable
HDMI
Cable
HDMI
Cable
HDMI
Cable
RJ45
Cable
D-Sub 9pin
Cable
PC