CYP CDPS-UA6H2HFS User manual

CDPS-UA6H2HFS
6 x 2 HDMI 4K UHD Matrix with HDCP 2.2
Operation Manual
Operation Manual

DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
- electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise - without express written permission and consent from
Cypress Technology.
© Copyright 2015 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack or install or
operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 01/07/15 Preliminary Release

CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel.........................................4
6.3 Remote Control................................5
6.4 IR Pin Denitions................................6
6.5 OSD Menu.........................................6
6.6 RS-232 Protocols .............................12
6.7 Telnet and RS-232 Commands .....12
6.8 Telnet Control .................................17
6.9 Web GUI Control ............................19
7. Connection Diagram .......................... 22
8. Specications ...................................... 23

1
1. INTRODUCTION
The 6 by 2 HDMI 4K UHD Matrix with HDCP 2.2 and Fast Switch which
allows HDMI signal from any of its 6 sources to be routed to and
displayed on any of its 2 connected HDMI displays simultaneously with
View All Mode and Picture-in-picture (PIP) supported. Fast switching
technology can greatly eliminate the time required by swapping or
turning ON/OFF the connected displays. It supports 4Kx2K, 3D, 30-
bit Deep Color, Hi-Def audio and other features dened by HDMI
specications.
The management of source/sink scenarios can be operated easily
through on-panel buttons, IR remote control, RS-232 or Ethernet
protocol.
2. APPLICATIONS
• Entertainment Room / Home Theater
• Show Room / Demo Room
• Lecture Room/Hall Presentation
• Show Room/Demo Room
• Public Commercial Display
• Information Board
3. PACKAGE CONTENTS
• 6 by 2 HDMI 4K UHD Matrix with HDCP2.2 and Fast Switching
• Remote Control with Battery
• Left & Right Rack Ears
• 5V/2.6A DC Power Adaptor
• IR Receiver Cable
• Operation Manual
4. SYSTEM REQUIREMENTS
Input source equipment such as Blu-ray/DVD/PS3 player or Set-Top-Box
and output HDMI TV/Display and or audio amplier with connection
cables.

2
5. FEATURES
• HDMI with 3D & 4Kx2K supported, HDCP 2.2 and DVI compliant
• Supports 6 HDMI inputs and 2 HDMI outputs
• Displays any of 6 High-Denition sources on 2 HDTV displays
simultaneously with fast switch
• When in Preview mode, the system will be treated as Switcher (2
HDMI output same images at the same time)
• In Preview mode, it support View All (1 Main video source and 5
Sub video sources) and PIP (1 Main video source and 1 Sub video
source). 3D and 4K2K sources inputs are not supported
• Note: View All is TDM (Time Division Multiplexing display)
• 3DTV Pass-Through
• Supports HDTV resolutions up to 4Kx2K (3840x2160@24/25/30 &
4096x2160 @30Hz)
• Supports Optical audio extraction
• Supports Optical audio sampling rate output up to 192kHz
• Supports data rate from 300Mbps to 3Gbps and Deep Color up to
1080p 30-bit
• Supports individual EDID or common EDID
• Supports LPCM 2/5.1/7.1CH, Dolby Digital 2~5.1CH, DTS 2~5.1CH
(Pass through), Dolby TrueHD and DTS-HD Master Audio
• Supports 6 sets of Matrix preset functions for input/output setting
• Input port HDCP support Standard and Apple mode. The Apple
mode selection to guarantees the use of Apple devices
• Compliant with DVI source (Not supporting Deep color and Color
space YCbCr 422/444)
• Supports OSD on output B under Preview Mode

3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
6X2 HDMI MATRIX FAST SWITCH
IN 1IN 2IN 3IN 4IN 5IN 6 MUTE
OUT A OUT B
POWER
TAKE
CANCEL
ENTER
MENU
PRESET
ALL
MODE
LOCK
+
-
1 2 4 5
3
6 7 8 10 14112 115
9 11 13
1Power & LED: Press the Power key to turn on the device and the
LED will illuminated.
2IR Window: IR Receiver receives remote control signal from the
remote control included in the package.
3OUTPUT A ~ B: Press these OUT buttons once along with one IN
buttons to select input source for select output display.
4IN 1~6: Press these IN buttons to select an input from 6 input
sources.
5MUTE: Press to mute audio source.
6TAKE: Press this button to conrm IN and OUT selection.
7CANCEL: Press this button to cancel IN and OUT selection.
8ENTER: Press this button to conrm selection.
9MENU: Press to enter Menu options.
10 +/-: Press to move up / down under menu options.
11 ALL: Press to select all outputs to display with one input source.
12 PRESET: Press this button, the OLED menu will show preset, then
select IN 1~6, press “TAKE” to conrm the selection or press
“CANCEL” to deselect.
13 LOCK: Press to lock all button functions on the panel, press and
hold 5 seconds to rescission lock mode.
14 MODE: Take mode / Real Time mode switch.
15 LCM: Display input and output selection and menu options.

4
6.2 Rear Panel
CONTROLSERVICE
HDMI IN HDMI OUT S/PDIF OUT
AB
123456AB RS232 IR IN DC 5V
1 2 3 4 5 6 7 8
1HDMI IN: Connect from source equipment such as Blu-ray / DVD /
PS3 player, Set-Top Box or any HDMI equipped source device for
input signal sending.
2HDMI OUT: Connect to HDMI TV / display or HD amplier for output
image and audio or audio display.
3S/PDIF OUT: Connect to Audio sound system or Amplier for digital
output sound.
4SERVICE: This is reserved for rmware update use only.
5CONTROL: Connect to PC / Laptop with active internet service for
Telnet / Web GUI control with RJ-45 terminated cable.
6RS232: Connect to PC / Laptop to control the device.
7IR IN: Connect the IR receiver which contented in the package for
receive IR signal from the remote control.
8DC 5V: Connect the adapter with power cord which included in
the package and connect to AC wall outlet for power supply.

5
6.3 Remote Control
1POWER: Press Power key to turn on
the device or set to standby mode.
2OUT A~B: Press these OUT buttons
once then to select an input source
for an output display.
3TAKE: Press this button to conrm IN
and OUT selection.
4MODE: Press to switch to matrix or
preview mode.
Matrix mode: Press OUT A or OUT B
or both then select from INPUT 1~6
or MUTE to select input sources,
press TAKE after selection to conrm
or press CANCEL to undo.
Preview mode: Select VIEW ALL or
PIP mode by entering Menu page.
Select to VIEW ALL: Press from INPUT 1~6 or MUTE to select input
sources for main channel.
Select to PIP mode: Press from OUT A~B then Press from INPUT 1~6
or MUTE to select input as main or sub video sources, press ALL or
SWAP to switch from main or sub video sources.
5PV DISP.: Press to switch Preview display on and off.
6SWAP: While in PIP mode, press to swap main or sub video source.
7MENU: Press to enter Menu options.
8ENTER: Press this button to conrm selection.
9+/-: Press to move up and down under menu options.
10 ALL: Press to select all outputs to display with one input source.
11 IN 1~6: Press these IN buttons to select an input from 6 input
sources.
12 CANCEL: Press this button to cancel IN and OUT selection.
13 PRESET: Press this button, the OLED menu will show preset, then
select IN 1~6, press “TAKE” to conrm the selection or press
“CANCEL” to deselect.
IN 3
IN 5
MUTEENTER -
OUT A
OUT B
MODE
PV DISP. PRESET IN 4
SWAP LOCK
ALLIN 1
TAKE IN 2
CANCEL
+MENU IN 6
CR-136
1
15
12
2
3
4
5
6
7
8
9
13
10
14
11

6
14 LOCK: Press to lock all button functions, press and hold 5 seconds
to rescission lock mode.
15 MUTE: Press to mute audio source.
6.4 IR Pin Denitions
3
1
2
IR Signal
Power
Grounding
IR Receiver
6.5 OSD Menu
Main Menu Sub Menu Description Default
EDID Mode All All Input ports are using
same EDID.
In menu “EDID All”,
can select suitable
EDID.
All
Appoint Each Input port can
select individual EDID.
In menu “EDID IN1~6”
select suitable EDID.
Exit
EDID All Sink A Copy Output A display
EDID
8/2D/
PCM/1080P
Sink B Copy Output B display
EDID
8/2D/
PCM/720P
Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.

7
Main Menu Sub Menu Description Default
8/2D/PCM/
AC3/720P
Standard EDID.
Content: deep
color/2D3D/audio/na-
tive resolution.
8/2D/
PCM/1080P
Standard EDID.
Content: deep
color/2D3D/audio/na-
tive resolution.
8/2D/PCM/
AC3/1080P
Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
8/2D/
PCM/4K2K
Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
8/2D/PCM/
AC3/4K2K
Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
8/2D/PCM/
Y420
Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
8/2D/PCM/
AC3/Y420
Standard EDID.
Content: deep
color/2D3D/audio/
native resolution.
Exit
EDID IN1 Same as EDID
All.
Select Input 1 EDID. Same as
EDID All.
EDID IN2 Same as EDID
All.
Select Input 2 EDID. Same as
EDID All.

8
Main Menu Sub Menu Description Default
EDID IN3 Same as EDID
All.
Select Input 3 EDID. Same as
EDID All.
EDID IN4 Same as EDID
All.
Select Input 4 EDID. Same as
EDID All.
EDID IN5 Same as EDID
All.
Select Input 5 EDID. Same as
EDID All.
EDID IN6 Same as EDID
All.
Select Input 6 EDID. Same as
EDID All.
Matrix Preset Preset 1 IN/OUT default No.1. A=1, B=2
Preset 2 IN/OUT default No.2. A=1, B=2
Preset 3 IN/OUT default No.3. A=1, B=2
Preset 4 IN/OUT default No.4. A=1, B=2
Preset 5 IN/OUT default No.5. A=1, B=2
Preset 6 IN/OUT default No.6. A=1, B=2
Exit
HDCP Input IN1 Standard/
Apple
Set IN1 in Standard/
Apple mode.
Standard
IN2 Standard/
Apple
Set IN2 in Standard/
Apple mode.
Standard
IN3 Standard/
Apple
Set IN3 in Standard/
Apple mode.
Standard
IN4 Standard/
Apple
Set IN4 in Standard/
Apple mode.
Standard
IN5 Standard/
Apple
Set IN5 in Standard/
Apple mode.
Standard
IN6 Standard/
Apple
Set IN6 in Standard/
Apple mode.
Standard
Exit

9
Main Menu Sub Menu Description Default
Preview
Mode
View All 1 Main video source
and 5 Sub video
sources.
View All
PIP 1 Main video source
and 1 Sub video
source.
Exit
Preview
Position
View
All
Top Preview 5 Sub screens
position.
Top Left
Right Preview 5 Sub screens
position.
Bottom Preview 5 Sub screens
position.
Left Preview 5 Sub screens
position.
PIP Top
Left
Preview sub screen
position.
Top
Right
Preview sub screen
position.
Bottom
Right
Preview sub screen
position.
Bottom
Left
Preview sub screen
position.
Exit
OSD
Transparency
0~15 Preview OSD
background
transparency.
6
Exit
OSD Timeout OSD Off Preview without OSD
info
OSD Always
On

10
Main Menu Sub Menu Description Default
5~20 Preview with OSD info
show 5~20 Seconds
then disappear
OSD Always
On
Preview with OSD
always on
Exit
Network
Setup
IP Mode DHCP, Static DHCP
IP Setup Static IP.
Mask Setup Static Mask.
Gate Setup Static Gateway
Do Re-Link Re-Link After Setup
Network, the System
need to re-link.
Exit
Network
Status
Link Network Status DHCP,
Static or Not Linked.
IP Get IP
Mask Get Netmask
Gate Get Gateway
MAC System MAC
Exit
Source
Detection
IN1 On/Off,
IN2 On/Off Detect IN1, IN2 source
with/without signal.
IN3 On/Off,
IN4 On/Off Detect IN3, IN4 source
with/without signal.

11
Main Menu Sub Menu Description Default
IN5 On/Off
IN6 On/Off Detect IN5, IN6 source
with/without signal.
Exit
Sink A Info Type, Manuf. Detect and analysis
Output A display’s
EDID.
Content: Type(HDMI/
DIV/VGA),
Manufactory/Model
number.
Native Content: Native
resolution.
Video Format Content: deep color,
2D/3D, 4K2K.
Audio Format Content: PCM,
Bitstream, HBR.
Exit
Sink B Info Same as Sink
A Info.
Detect and analysis
Output B display’s
EDID.
Firmware FW Version Display Model number
& FW Version.
Update FW Update.
Exit
Factory Reset Do Reset Do System Reset.
Exit
Exit

12
6.6 RS-232 Protocols
Matrix
►
◄
Remote Control
PIN Denition PIN Denition
1 NC 1 NC
2 Tx 2 Rx
3 Rx 3 Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 115200bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
6.7 Telnet and RS-232 Commands
Command
Name Description Description of parameter
P0 Power Off (Standby) NONE
P1 Power On NONE
IPCONFIG Display The Current
IP Congure
NONE
SIPADDR
X.X.X.X
Set Ethernet IP
Address
X=0~255
SNETMASK
X.X.X.X
Set Ethernet Net
Mask
X=0~255
SGATEWAY
X.X.X.X
Set Ethernet
Gateway
X=0~255

13
Command
Name Description Description of parameter
HTTPPORT N1 Set Http Port Number N1=0~65535
TELNETPORT
N1
Set Telnet port
number
N1=0~65535
RSTIP IP Conguration Set
To <DHCP>
NONE
A N1 Set Output A Source
to input N1
N1=1~6
B N1 Set Output BSource
to input N1
N1=1~6
I N1 Set All Outputs
Source to input N1
N1=1~6
EDIDMODE Show EDID Mode NONE
EDIDMODE N1 Set EDID Mode N1=0(Appoint), 1(All)
EDIDALL Show EDID Mode
Source for All
NONE
EDIDALL N1 Set EDID Mode
Source for All
N1=0(Sink A), 1(Sink B),
2(8/2D/PCM/720p), 3(8/2D/
PCM/AC3/720p), 4(8/2D/
PCM/1080p), 5(8/2D/
PCM/AC3/1080p), 6(8/2D/
PCM/4K2K), 7(8/2D/PCM/
AC3/4K2K), 8(8/2D/PCM/
Y420), 9(8/2D/PCM/AC3/
Y420)
EDIDIN Show Input EDID
Source
NONE
EDIDIN N1 Show Input N1 EDID
Source
N1=1~6

14
Command
Name Description Description of parameter
EDIDIN N1 N2 Set Input N1 EDID
Source
N1=1~6
N2=0(Sink A), 1(Sink B),
2(8/2D/PCM/720p), 3(8/2D/
PCM/AC3/720p), 4(8/2D/
PCM/1080p), 5(8/2D/
PCM/AC3/1080p), 6(8/2D/
PCM/4K2K), 7(8/2D/PCM/
AC3/4K2K), 8(8/2D/PCM/
Y420), 9(8/2D/PCM/AC3/
Y420)
HDCPIN Show All Input HDCP
Status
NONE
HDCPIN N1 Show Input N1 HDCP
Status
N1=1~6
HDCPIN N1 N2 Set Input N1 HDCP
ON/OFF
N1=1~6
N2=0(OFF), 1(ON)
PRESET Show All Preset
Congure
NONE
PRESET N1 Set Preset N1 Source
to Outputs
N1=1~6
PRESET N1 N2 Set Preset N1
Congure N2
N1=1~6
N2=AXBX (X=1~6)
PVMODE Show preview mode NONE
PVMODE N1 Set preview mode to
N1
N1=0(View all), 1(PIP)
PVPOS Show preview mode
position
NONE

15
Command
Name Description Description of parameter
PVPOS N1 Set preview mode to
N1
In view all mode:
N1=0(Top), 1(Right),
2(Bottom), 3(Left)
In PIP mode:
N1=0(Top), 1(Top right),
2(Bottom Right), 3(Bottom
Left)
PVSRC Show preview mode
source select
None
PVSRC N1 In VIEWALL mode:
Set Main Screen
Source To Input N1
In PIP mode:
Show N1 screen
source select
In VIEWALL mode:
N1=1~6
In PIP mode:
N1=0(Main), 1(Sub)
PVSRC N1 N2 Set PIP mode main/
sub screen source to
input N2
N1=0(Main), 1(Sub)
N2=1~6
OSDTRANS Show OSD
transparency
NONE
OSDTRANS N1 Set OSD
transparency
N1=0~15
OSDTO Show OSD time out NONE
OSDTO N1 Set OSD time out N1=0(OSD off), 1~16(5~20),
17(OSD always on)
SOURCEDET Show All Input Signal NONE
SOURCEDET
N1
Show Input N1 Signal N1=1~6
SINKINFO Show All Output
Information
NONE