CYP Elpro Video Labs CDPS-UC4H4HFS User manual

CDPS-UC4H4HFS
4 by 4 HDMI 4Kx2K Matrix with Control System
Operation Manual
Operation Manual

DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2015 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE
VR0 24/09/15 Preliminary release
VR1 17/02/16 releaseRS-232 Command case-
insensitive

CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 2
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Front Panel ........................................3
6.2 Rear Panel.........................................4
6.3 Remote Control................................5
6.4 OLED Menu .......................................6
6.5 IR Cable Pin Assignment................10
6.6 RS-232 Protocol...............................11
6.7 RS-232 and Telnet Commands .....11
6.8 Software Application.....................15
6.9 Telnet Control .................................16
6.10 WebGUI Control ...........................18
6.10.1 Routing Settings...................18
6.10.2 EDID Settings........................19
6.10.3 Macro Settings ....................19
6.10.4 Command Settings.............22
6.10.5 Trigger Settings ....................23
6.10.6 UART Settings .......................23
6.10.7 Network Settings .................24
6.10.8 System Settings....................24
7. Connection Diagram .......................... 25
8. Specications ...................................... 27
8.1 Technical Specications ...............27
8.2 Supported Resolutions...................28
9. Acronyms ............................................. 29

1
1. INTRODUCTION
This 4K2K 4 by 4 Matrix with fast switch and control system allows 4
HDMI signal sources being displayed in 4 connected HDMI displays in
the way you like, fast switching technology can greatly eliminate the
time required by swapping or turning ON/OFF the connected displays.
Control system features support traditional direct control systems like
IR, Relay and DC trigger and indirect control systems like IR Learning,
RS-232, Telnet/WebGUI controls. Allowing user with PC or APP controls
great exibilities over controlling devices. The operation of the system
can be easily managed through software application on PC/Laptop
or APP on mobile devices and moreover, through on-panel buttons, IR
remote, RS-232, Telnet and Ethernet protocols.
2. APPLICATIONS
• Entertainment Room / Home Theater Display and System Controls
• Show Room / Demo Room Display and System Controls
• Lecture Room/Hall Presentation Display and System Control
• Public Commercial Display and System Control
• Information Board Display and System Control
3. PACKAGE CONTENTS
• 1×4 by 4 HDMI 4K UHD Matrix with Fast Switch
• 1×Remote Control with Battery
• 1×Left & Right Rack Ears
• 1×IR Extender Cable
• 1×5 V/3.6 A Power Adaptor
• 1× Power Cord
• 4×Terminal Blocks
• 1×IR Learner Cable
• 4×3.5 mm to 3.5mm IR Cable
• 1×IR Blaster
• 1×Operation Manual

2
4. SYSTEM REQUIREMENTS
• Input source equipment such as Blu-ray/DVD/PS3 player or Set-
Top-Box and output HDMI TV/Display and or audio amplier with
connection cables.
• Control system input devices such as security door/windows,
lights, curtain, or devices like players, sound systems, or any other
controllable device with IR/RS-232 or net service link design with PC/
smart phone to send commands to control the whole system.
5. FEATURES
• HDMI with 3D & 4Kx2K supported, HDCP and DVI compliant
• Support 4 HDMI inputs and 4 HDMI outputs
• Supports HDTV resolutions up to 4Kx2K (3840x2160@24/25/30,
3840x2160@50/60_YUV420 & 4096x2160 @24, 4096x2160 @50/60_
YUV420)
• Supports individual EDID or common EDID
• Supports pass through of audio formats: LPCM 2/5.1/7.1CH, Dolby
Digital 2~5.1CH, DTS 2~5.1CH, Dolby Digital Plus, Dolby TrueHD,
Dolby Atmos and DTS-HD Master Audio
• HDCP 1.4 for 4 HDMI inputs and 4 HDMI outputs.
• Input port HDCP support Standard and Apple mode. The Apple
mode selection to guarantees the use of Apple devices
• Compliant with DVI source (Not support Deep color and Color
space YCbCr 422/444)
• Supports IR Learning function: Allows IR signals to be stored in the
system and used for control
• Supports eight Terminal Block inputs with voltage of 5~15V
• Supports 1 IR Learning port, 8 IR outputs, 8 control inputs, 8 Relay
outputs, 2 COM ports, and 4 Ethernet ports
• Supports Baud rates up to 115,200bps
• Supports 10/100Mbps Ethernet network connection

3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER
IN 1IN 2IN 3IN 4TAKE
OUT AOUT BOUT COUT DCANCEL
ENTER
MENU
PRESET
ALL
MODE
LOCK
+
-
POWER
IN 1IN 2IN 3IN 4TAKE
OUT AOUT BOUT COUT DCANCEL
ENTER
MENU
PRESET
ALL
MODE
LOCK
+
-
4X4 HDMI MATRIX FAST SWITCH
1 2 4 5
3
8 9 13111 114
710 12
6
1POWER: Press this button to turn ON the device and the LED will
illuminated.
2IR WINDOW: This IR Receiver receives the remote control signal
from the package include remote control only.
3OUT A~D: Press OUT button along with an IN buttons to select an
input source for an output display. i.e. OUT A→ IN1→TAKE or OUT
A→OUT B→IN4→TAKE.
4IN 1~4: Press IN button to select input from 4 sources.
5TAKE: Press this button to conrm the selection of an IN and an OUT
button. If this button is not pressed the selection will not execute.
6CANCEL: Press this button to cancel the selection.
7MENU: Press to enter into the menu.
8ENTER: Press to conrm selection.
9+/- : Press to select page up and down under menu select.
10 ALL: Press to select an input into all output.
11 PRESET: Press this button, the OLED will show preset selection then
select from IN 1~4 and press “TAKE” to conrm the selection or
press “CANCEL” to cancel the selection.
12 LOCK: Press to lock on all button functions on the front panel. Press
for 3 seconds to relieve the lock function.
13 MODE: Press this button to switch in between the TAKE mode/Real
Time mode. OLED will show current selection on the top right side,
press TAKE to conrm the switch.
14 OLED: Display input and output selection and menu selection.

4
6.2 Rear Panel
IN OUT
IRL INFRARED OUT COM 1 COM 2 LAN
CONTROLSERVICE RS232 IR IN
DC 5V
HDMI IN HDMI OUT
1234ABCD
1234
12345678
1 2 4 5 7 8
3 6 9 10 11 12 13
1IRL: Connect with IR Receiver included in the package for IR signal
learning. Send the IR signal that is to be learned by press on the
remote control in direct line-of-sight towards the Receiver and use
WebGUI to store and transmit the IR code. Details please refers to
section 6.10.4
Note: Although both IR Extender and IR Learner may look the same
they are however different. IR Extender is designed with more
reddish color whereas IR Learner has a brownish color and a red
dot on the back to be distinguished in between. Please pay extra
attention in connecting and using them.
2INFRARED OUT 1~8: Connect with IR Blaster for IR signal transmitting.
3HDMI IN 1~4: Connect from source equipment such as Blu-ray/
DVD/PS3 players, Set-Top-Box or any HDMI equipped source
device for input signal sending.
4TRIGGER IN 1~8: Connect with event device’s signal lines such as
window security alarm, door switch, and etc… that obtain voltage
from 0~15v For signal trigger sending back to Control System
which works align with Macro setting 1~8 from WebGUI. The upper
row should connect with positive voltage and the lower row are
negative pin, if the lines are miss connected, no signal/action will
be active. For detail connection please referes to below diagram.
5RELAY OUT 1~8: Connect with control device’s power ± line cable
such as DC Power supply to activate the control devices.

5
6HDMI OUT A~D: Connect to HDMI TV/display or HD Amplier for
output image and or audio display.
7COM 1~2: Connect with devices that obtain RS-232 input for
control purpose. Using TELNET client to send command directly to
control the device, set the connected port to 7501 with COM 1
and 7502 with COM2.
8LAN1~4: Connect with devices that obtain RJ-45 input for control
and data transmitting purpose within the connected LAN system.
9SERVICE: This slot is reserved for rmware update use only.
10 CONTROL: Connect from PC/Laptop with active internet service or
Ethernet switch/Hub for WebGUI control and or data transmitting.
11 RS-232: Connect from PC/Laptop for RS-232 command sending to
control the device.
12 IR IN: Connect the IR Receiver included in the package for IR signal
receive from the included remote control. Ensure that remote
being used is within the direct line-of-sight of the IR Extender.
13 DC 5V: Connect the adaptor with power cord included in the
package and connect to AC wall outlet for power supply.
6.3 Remote Control
1POWER: Press this button to switch the
system ON/OFF.
2OUT A~D: Press these buttons once a
time along with an IN buttons to select
an input source for an output display.
3IN 1~4: Press the IN buttons to select an
input from the 4 input sources.
4ALL: Press this button to select all outputs
to display with an input source.
5TAKE: Press this button to conrm the
selection of an IN and an OUT button. If
this button is not pressed the selection
will not execute.
6CANCEL: Press this button to cancel the
selection.
MODEENTER
OUT A
OUT B
OUT C
OUT D PRESET
LOCK
ALL
TAKE
IN 3
IN 4
IN 1
IN 2
CANCEL
-
+
MENU
CR-138
1
2
9
10
3
12
6
4
11
5
7
8